Do you need to use carbon deposits to clean the engine oil during the run in period of the motorcycl

No, just change it.

If you don't need to change the oil, the cleaning of carbon deposits will not affect the oil. Remove the engine trim cover, remove the throttle valve, wash it with carburetor cleaner, dry it with a cotton cloth and install it. The throttle cleaning interval is 20,000 km.

Precautions for cleaning internal carbon deposits.

Open the oil cap, pour the whole tank of cleaner (mixed with old engine oil), close the oil cap, idle for 10 minutes, and then turn off the ignition. Cleaning the carbon deposits inside the engine, the detergent dissolves the sediments such as sludge, gum, moisture and metal debris inside the engine, and can reduce the pollution of new engine oil and prolong the service life of the engine.

The cleaning method of carbon deposits inside the engine is also very simple, only need to add a bottle of engine internal cleaning agent to the oil port before maintenance, and idle for about 10 minutes, and then immediately maintain and replace the oil filter.

Engine carbon cleaning does not require oil changes, and cleaning carbon does not affect the oil, so there is no need to change it. There are several ways to remove carbon deposits from a car, and here's how:

1. Hang the bottle in the car, hang a bottle-shaped tool above the engine, then pour the detergent into the bottle-shaped tool, and introduce it into the engine through the conduit to facilitate the cleaning of carbon deposits;

2. Machine washing, inject the cleaning agent into the machine, and then use the pressure of the machine to contact the combustion chamber to dissolve the cleaning agent and carbon deposit, and then discharge the waste liquid;

3. Engine dismantling and cleaning, this method should be the most effective, directly remove the entire engine, and use detergents, ultrasonic and other means to completely remove carbon deposits on parts.

The impact of engine carbon deposition on the car is still quite large, first of all, to reduce the engine power, that is, to make the power output uneven and gradually decay, in other words, more and more powerless. The second is to increase fuel consumption and increase your financial burden. The third is the difficulty of cold start, that is, the difficulty of ignition, and it is not easy to get on the car.

Finally, serious carbon deposition in the combustion chamber will also cause cylinder detonation, and there will be a sound of low-speed acceleration, which will cause damage to the piston and crankshaft, thus seriously affecting the safety of the car. Then there is the excessive discharge, which not only fails the annual inspection and inspection, but also directly aggravates the harm of polluting the environment. The specific principle is that if you do not pay attention to the oil and driving habits for a long time, the wax and gum in the gasoline will accumulate thicker and thicker, and carbon deposits will be formed when they harden after repeated heating.

If the engine burns oil, or if the gasoline is of poor quality and has more impurities, the valve carbon deposits are more serious and form faster. Because the structure of carbon deposition is similar to that of a sponge, when the valve forms carbon deposition, a part of the fuel injected into the cylinder will be adsorbed, which makes the concentration of the mixture that really enters the cylinder thinner, resulting in poor engine work, and abnormal phenomena such as difficult starting, unstable idling, poor acceleration, urgent refueling and tempering, excessive exhaust gas, and increased fuel consumption. If it is serious, it will cause the valve to be closed loosely, so that there is no cylinder pressure in the cylinder and it will not work completely, and even adhere to the valve to prevent it from returning.

At this point, the valve and piston will interfere with the movement, which will eventually damage the engine.

Hello, you don't need to change the engine oil to clean carbon deposits, such as: throttle, fuel injector, intake tract, three-way catalysis, if you clean engine sludge, you need to change the oil, I hope my answer can help you.

To clean the carbon deposits inside the engine, cleaning agents are generally added to the old engine oil, and the carbon deposits are discharged together with the old oil after running the car for a period of time.

It mainly depends on the area you are cleaning and the type of cleaning agent you are using.

No, the combustion system and the lubrication system are not connected.

It shouldn't matter what method you use to clean it.

Motorcycle oil can be changed as much as possible when the car is hot to be clean.

In the case of a hot car (the hot car oil is thin and easy to control), control it for a while, and shake it from side to side.

You can also use kerosene to flush, put the oil clean and pour kerosene, slowly step on 2-3 feet, don't hit, just release it slowly.

Engine oil, that is, engine lubricating oil, is known as the "blood" of the car, which can lubricate, clean, cool, seal, reduce wear, prevent rust and corrosion of the engine.

Steps to change the oil in a hot car of a motorcycle:

1. Unscrew the oil drain plug, under the engine, 17 nuts.

2. Unscrew the oil dipstick and remove it to facilitate the release of oil, 3. Wait, and finally you can tilt and shake the body until the oil is exhausted, and you can wash it with kerosene if conditions permit.

4. Tighten the oil drain plug, pay attention to the strainer and sealing ring on the nut.

5. Add new engine oil. If it is winter, pay attention to changing to antifreeze engine oil.

Try to put the oil bolts as clean, but they will not be absolutely clean, and there will always be a small part of the residue.

1. Practice has proved that after the old oil is released by the normal oil opening bolt, new oil will be added, and there will be no engine overheating, power decline, driving weakness, incomplete clutch separation, oil seal leakage and other failures.

2. After a small amount of residual old oil is mixed with the new engine oil, it will not seriously deteriorate the new engine oil.

3. Whether it is a motorcycle or a car, it is impossible to completely clean the original old oil in the oil change process, so there is no absoluteness in anything, and the oil is changed regularly as required, and the life of the motorcycle will not be too harmful.

The practical experience answers hope you are satisfied.

After the car is warmed, the main bracket is erected on the flat ground, the oil drain screw plug is opened, and the body can be gently shaken left and right until no oil flows after the car is released. There are some small compartments at the bottom of the engine, which cannot be completely cleaned anyway, so this is enough. If there are small impurities during running-in, they will precipitate at the oil drain screw, which will be discharged with the old engine oil, and there will not be as many dirty things as imagined, so there is no need to clean, just add an appropriate amount of new oil after putting the old oil.

It is not recommended to use gasoline or diesel for cleaning, first, it is not necessary, and secondly, the residual gasoline and diesel will destroy the oil quality of the new engine oil and affect the lubrication effect. The oil drain screws are all at the lowest point of the engine, which can completely drain the old oil that needs to be replaced.

The first oil change for all Qingqi Suzuki products is 1000 kilometers, because there is a special running-in agent in the engine oil that leaves the factory, and it is in vain to change it in advance. After the first 1000 km change, every 2000 km after that. In addition to the regular air cleaning on the line, there is no excessive maintenance content, the superhuman air filter inlet is under the seat cushion, relatively clean, and the filter element is not easy to get dirty.

It is best to warm up for a few minutes when starting the cool car, because after leaving it overnight, the oil sinks to the bottom of the engine, and increasing the throttle immediately after starting will cause the engine to wear due to inadequate oil lubrication. Moreover, the cool car is a large gap between the parts, and driving immediately without preheating will also have a negative impact on the life of the engine.

You said that you added new engine oil without putting the original engine oil, this is impossible, it may be that you didn't pay attention to the oil they put it.

When changing the engine oil of the motorcycle, use the main bracket to support the car on the flat ground, remove the oil drain screw to release the oil, and slightly tilt to the left and right sides respectively, you can put the oil clean, do not step on the starting lever, do not start the engine, do not pour gasoline or other liquid into the engine to clean, so that you can put the oil clean.

Summary. Hello, the first oil change of a new motorcycle is best 300 kilometers, because during the run-in period, there will be a lot of metal iron filings mixed in the oil, the oil machine filter can not filter it, it is randomly oil pumped on the surface of each friction, accelerating the wear of the friction surface. It is to change the oil and let it drain along with the oil.

The second oil change was 600 kilometers, and a small amount of iron filings could be seen in the oil changed the second time, but it was much less than the first time. The third oil change is at 1000 km, and the motorcycle oil selection precautions If the vehicle belongs to the state of high use frequency and has been out of the run-in period, it is recommended to choose a fully synthetic lubricating oil.

How many kilometers to change the oil during the run-in period of the new motorcycle.

Hello, the first oil change of a new motorcycle is best 300 kilometers, because during the run-in period, there will be a lot of metal iron filings mixed in the oil, the oil machine filter can not filter it, it is randomly oil pumped on the surface of each friction, accelerating the wear of the friction surface. It is to change the oil and let it drain along with the oil. The second oil change was 600 kilometers, and a small amount of iron filings could be seen in the oil changed the second time, but it was much less than the first time.

The third oil change is at 1000 km, and the motorcycle oil selection precautions If the vehicle belongs to the state of high use frequency and has been out of the run-in period, it is recommended to choose a fully synthetic lubricating oil.

Pro, motorcycle oil change is 1000 kilometers before the new car during the run-in period is the standard is incremental replacement. After that, it can be changed according to the number of kilometers traveled and the time limit of the use date, and whichever arrives first will change the oil. After using mineral oil, it should be changed every 1,500 km, and if full synthesis is used, it can be extended to about 3,000 km.

The functions of engine oil are: to relieve friction and high temperature; Reduce gas leakage and prevent external pollutants; Prevent contact between water, air, acidic and harmful gases and parts; Cushion the rise of engine cylinder port pressure; Rinse the dirt generated on the work surface of the part.