How to set up D Link Dir 616

1. Log in to the router configuration page.

Open the browser and enter it in the address bar, the default user name of D-Link is admin, and the password is empty.

2. After logging in, choose to manually set up the Internet connection, according to your network access type to set up, there are generally three kinds, 1) DHCP: that is, the operator only provides you with the line, no other information, plug the network cable into the computer to access the Internet, in this case, the access mode is DHCP, and then click Save;

2) Static IP: Static IP, that is, the operator provides you with IP address, subnet mask, gateway and DNS address, then you need to choose the static IP method, and then fill in the above information into the router to save;

3) PPPoE: This is more commonly used, most of them are ADSL, that is, the operator provides you with a username and password, dial-up Internet access, then you need to choose the PPPoe method in the router, and then fill in the username and password into the router, and the following connection method selection is always.

As of now, the router can be connected to the Internet, of course, you must also check whether the physical wiring is correct, and the incoming cable given to you by the operator should be plugged into the WAN (Internet) interface of the router.

3. Set up wireless.

In the wireless settings, you need to change the SSID (wireless network name), and then encrypt it, and it is recommended to use WPA WPA for encryption, and the password is 8 digits or more digits or more digits or letters.

If it is the first time to set up, you must first connect it with a network cable to the computer.

The steps are here.

How to set up the dlink616 router:

Home Network Environment Cabling]:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoE Dialing] (some are ADSL dialing), enter the username and password (provided by the network service provider) according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

1. First of all, it is recommended to try the initial default password of the router, the default account password of most routers is: admin, part is: guest, if you are not clear, you can read the label or instruction manual on the back of the router.

2. If the password is incorrect. Then reset the router. There is a small port on the side of the network cable port of the router, which is the reset button.

The reset button needs to be pressed with a toothpick, needle or refill and other slender things, keep holding the reset button for more than 8 seconds, and then you will see all the indicators flash at the same time, indicating that the reset is successful. After the reset, all the settings of the router are restored to the default values, and the login password of the router becomes the initial password.

Account admin

Password admin or empty password.

Hello! Here's how to set up the D-Link DIR-868L wireless router

1. Connect the power supply of the router, and then plug one end of a network cable into the network port of the computer, and the other end into the LAN port of the router.

2. Open the browser of the computer, enter the IP of the router in the address bar, click the enter key to enter the settings page of the router, the user name is admin, the password is blank, click to log in, and enter the settings home page of the router.

3. After logging in to the homepage, select Manual Settings. Then select Manual Internet Settings, and Home Dial-up users select the PPPoE connection type. In the username and user, enter the username and password given by the ISP provider (Netcom, Great Wall, Telecom, Tietong, Cable, etc.) correctly.

The connection mode selection is always filled in with the mtu value of 1492. The save is done.

4. The wireless router also has a wireless encryption to ensure the user's wireless security. Select the wireless settings on the main page of the router's settings, select an encryption method in the security mode, any one of WEP, WPA, or WPA2, and then enter 8 or more Chinese characters or numbers as the wireless password in the security key, and the router settings will be completed after saving the settings.

5. After the setting is completed, the router will automatically restart, and the external network cable can be used by connecting the external network cable to the WAN port of the router.

If you want to use wifi, restart the router first, then log in and enter the account password, and then set the routing password and the routing will automatically restart, and you can use it after a while.

I can search but can't get on the Internet because I am connected to the route, and the route is not dialed.