-
1. After the car is pasted, avoid raising and lowering the window within 3-7 days, 2. Do not wash the car within a week, and do not rinse the high-pressure water gun against the film;
3. In winter, the rear gear can not be opened within one month to avoid blistering due to the addition of **;
4. Always have a microfiber wiping cloth with high adsorption capacity in the car for daily wiping. Keep the film clean and clean;
5. Do not stick toys and ornaments on the film;
6. It is best to use wet towels, paper towels dipped in water or cotton cloth with dish soap to clean.
In fact, brands like Opas will have professionals to inform these film maintenance details to avoid damage to the film caused by human misoperation. "
-
The car film is not so squeamish, and you can wash and wax everything normally.
-
When you want to remove the stickers or window grilles on the glass, it is more difficult to clean them up in general, especially the stickers that have been used for a long time, either leaving stains or sticky gum that are not clean. Today I will tell you an easy and quick way.
First of all, use a knife to pick out a corner of the film, never use a knife to scrape the film, this will only leave more gum on the back of the film. After picking it up, you can tear the film directly, and the glue left on the glass will be relatively less.
Then, use the transparent glue with a relatively large adhesive line to glue off the remaining spots, and both hands can press the transparent glue vigorously at the same time, and then quickly remove it, so that the glue on the film will be removed.
-
1.Do not directly clean the windows with water within 7 days after the car film is applied, so as not to cause the car film to fall off due to the moisture not drying; Try not to open the rear window defogging line within two weeks (winter), and it is easy to have a negative impact on the defogging line before the moisture dries; When the car film is installed, wipe the film surface with a wet towel, sponge or soft cloth;
2.If the film is accidentally loosened during the car wash, then we must return to the professional sticker shop for you in time to let the professional construction personnel for you'Automotive membranes are repositioned to ensure effectiveness and durability. After 30 days of filming, you can use the usual household cleaning methods to clean the car.
3.It is recommended that you try not to stick or hang things directly on the car window after applying the film, so as not to open the gap of the film when the suction cup or paste is pulled up.
4.Rational use of glass water, now there are many kinds of glass water in the domestic market, but there are mainly three types: glass water for summer, antifreeze glass water for winter and special effect antifreeze glass water.
Among them, the glass water used in summer is mainly used to remove the residue of flying insects on the mirror surface; The anti-freeze glass water in winter is mainly to ensure that when the temperature is lower than minus 20, the parts of the car will not be frozen; The special antifreeze type glass water is mainly used in the particularly cold areas of the north to ensure that the car does not freeze at minus 40.
1.Car owners think that the film is better in the summer than in the winter. In fact, this is not true, some people even if they buy a car in winter, they have to wait until summer, this is not necessary, when to choose a film has nothing to do with the season, it is best to apply the film when you are in a new car.
2.The film generally chooses a sunny day, once it rains, few people choose this kind of weather, in fact, this idea of empty rolling is also incorrect, rainy days can still be filmed, mainly in an indoor closed environment, and the air in rainy days is better, there will be little dust, so no matter what weather can be carried out.
3.The darker the color of the heat insulation film, the more heat insulation, in fact, it is wrong, its heat insulation effect does not depend on the color, or on the function of heat absorption and the effect of reflection.
4.The higher the car film, the better, this is not true, although it is said that a penny is a penny, but many criminals will take the bad as good, or to see if it is a real film.
1.Generally speaking, it takes 5-7 days for the car film to be firmly attached to the car window. During this period, try not to lift or lower the glass to avoid the displacement of the car film that has not been fully bonded.
2.Newly applied car films are prone to fogging and other conditions, which is a normal phenomenon in the drying process of solar films. Generally, it is normal for this situation to occur in about a week to half a month, and you only need to wait for it to disappear slowly, and you must not wipe it.
3.After the car is applied, do not use sharp, coarse and hard sharp tools to scrape. Because if the owner does not pay attention, after the car film is scraped with a sharp and hard sharp weapon, the light transmittance of the car film will be greatly reduced.
Therefore, Haiqiao Century car film technician reminds the majority of car owners to wipe the film surface with soft cloth such as wet towels as much as possible when washing the car after the car film, and to avoid using corrosive chemical solvents to wipe the car film surface.
-
Generally, junior technicians can only apply film to the side windows, while only intermediate and senior technicians can apply film to the front windshield with a large curvature.
Before the film, it is necessary to check whether the installation of the window glass is intact and the integrity of the car glass to ensure that the subsequent film work can operate normally.
Be sure to cover the necessary parts of the car before applying the film to prevent liquid from penetrating. Sprayed cleaning fluids and lubricating fluids can affect trim parts such as automotive electronics and interior seats.
Wash the interior and exterior surfaces of the windows before applying the film (focusing on the interior surfaces and glass sealant areas). This is mainly to eliminate the dirt or other object construction quality problems between the film and the window glass after the film, and ensure that the film and glass can be perfectly combined.
The membrane is pre-cut. Use a ruler to measure the size of the front and rear windshields, and cut the film according to the measured size. (The professional rubber film mechanism is through the computer, and the computer is tailored according to the model).
Spray the installation fluid. Dust spots can be avoided and corrosion at the edges can be reduced, resulting in the desired viscosity and better application results.
Dry roasting, wet roasting shaping. The film is dry-roasted first so that the film can be fully pre-shrunk. In order to further improve the adhesion of the heat insulation film, it is also necessary to wet bake and shape the heat insulation film.
Extrusion of the installation fluid: In the process of using the wiper to remove the installation fluid, try to scrape the installation fluid between the heat insulation film and the window glass, which can reduce the drying time of the heat insulation film and obtain a better bonding effect, overall performance and visual effect.
Check after sticking. "Three looks and one attention": look at the entire heat insulation film to see if there is any dust and bubbles, see whether the corners are firmly glued, and sit in the car to see if there are any places that affect the line of sight (especially the front windshield and side windshield). After the film, it is recommended not to raise or lower the glass arbitrarily within 48 hours.
The most important thing to pay attention to when applying the film is the use of hair dryer, if you blow this place for a long time, it will cause the glass to crack due to uneven heating. Therefore, the film should find those professional authorized stores, so that the quality of the film will be ***, and the danger of glass cracking can be avoided.
Also, the car film is best in rainy weather, and when it is pasted on rainy days, there is very little dust in the air, which has certain benefits for aesthetics.
-
<> "Car Film Maintenance Method.
Nowadays, almost all car owners will apply film for their cars, but how to maintain the car film has become a big problem. To this end, relevant experts said: try to avoid washing the car within three days after the film, so as not to cause the film to fall off before the moisture dries.
Try not to open the rear window defogging line within a week, and it is easy to have a negative impact on the defogging line if the moisture is not dry. After attaching, you can wipe the film surface with a damp towel, sponge or soft cloth. In addition, some time after applying the film, you will notice that there is a foggy water vapor inside.
This is a normal phenomenon in the process of drying the solar film, and it will slowly disappear after a while.
It takes 5-7 days for the sun film to be firmly attached to the window, so the film is easy to grind and curl during the hail process of the window opening and closing, and the film that has not been fully bonded is also prone to displacement. High-quality car film usually has good wear resistance, the film layer is used between the use of special high-performance resin glue, the adhesion is very outstanding, can achieve the film edge and the glass edge is only 2 mm difference is still not easy to wear, and the anti-scratch coating makes it have a strong anti-scratch performance, and the life is long and easy to maintain. On weekdays, lifting windows is also easy to wear the film surface, and the inferior film will be scratched after one or two months, and choosing a high-quality car film can avoid this situation.
If you accidentally loosen the film during the car wash, you should go back to a professional film shop and have it re-fixed by a professional to ensure the effect and durability. If there is a stain on the surface of the film, do not wipe it with chemical Libi solvent, it is best to use a wet towel for cleaning, a paper towel dipped in water or a cotton cloth with dish soap, or you can use a rubber wiper to clean it. However, avoid using abrasive items and tools that can scratch or damage the film to avoid damaging the solar film.
In addition, experts suggest that after the vehicle is filmed, try not to paste or hang things directly on the window, so as not to open the gap between the film when pulling up the suction cup and paste.
-
When there are stains on the surface of the film, many people will habitually pick up the glass cleaner, spray it, and wipe it with a rag.
As everyone knows, this will have a great impact on the life of the explosion-proof heat insulation film, because most of the explosion-proof heat insulation film contains metal components, and corrosive chemical cleaning agents will react with these metals, resulting in fading, deformation, and blistering. However, wiping it with a rough rag will scratch the insulating film and produce scratches.
So how to properly maintain the dirty car film?
In fact, under normal circumstances, if you find that there are stains on the car film, as long as you use a soft rag in time and gently wipe it with some warm water. Fingerprints, oil stains, and stains on the heat insulation film can be wiped clean.
In addition, it is better not to put jewelry on the car film. For the sake of aesthetics, many people will stick some decorations on the car film, or adsorb it through a suction cup, which can easily cause the car film to fall off.
The above is all the content of how to maintain the car film introduced by Bian Xiao. You should know how to maintain the car film.
-
Car film is our common car maintenance content, which can prevent the car from being scratched, so what are the precautions after car film?
Keep the offcuts in the film! Pick up two pieces of film scraps when applying the film, and then ask the clerk to staple it on the warranty card and sign or stamp it when you check out after the construction. to prove that the membrane was sold from the store.
Reminder: The warranty card and leftovers are particularly important, there have been riders who have pasted a fake 3M film, just because there is no 3M electronic warranty card, 3M company does not provide a test certificate, and the result can not continue to protect rights. Another important point is that you must buy the sticker at the local authorized store, if it is an online delivery OEM, even if there is a warranty card, because it is a cross-shipment, 3M official does not recognize.
Precautions for maintenance after car filming
1. It is best not to wash the car within two days after the film is applied, so as not to cause the film to bubble before the moisture dries. Try not to use the rear window defogging function within a week, and it is easy to have a negative impact on the defogging line if the moisture is not dry. After attaching, you can wipe the film surface with a damp towel, sponge or soft cloth.
2. Within 5 days after the film, you should rent a file and try to avoid lifting and lowering the windows, especially for new cars that have just finished pasting the film. It takes 3-5 days for the solar film to be firmly attached to the window, and the newly attached film edge is easy to curl during the window opening and closing, and the film that has not been fully bonded is also prone to displacement. A good quality car film usually has a good one.
Abrasion resistance, the film layer is used with special high-performance resin glue, the adhesion is very outstanding, can achieve the film edge and the glass edge is only 2 mm difference is not easy to wear when the film is still not easy to warp, and the patented anti-scratch coating makes it have strong anti-scratch performance, and long life is easy to maintain. On weekdays, lifting windows is also prone to abrasion to the membrane surface. Scratches will appear after a month or two of inferior film, and choosing a high-quality car film can avoid this.
3. After applying the film, do not wipe it with chemical solvents, it is best to use a wet towel for cleaning, a paper towel dipped in water or a cotton cloth with dish soap, or you can use a rubber wiper to clean it. However, avoid using abrasive items and hard tools that can scratch or damage the film to avoid damaging the solar film.
4. Many car owners like to hang small ornaments on the windows. In fact, whether the suction cup is still sleepy, it is an item that is directly attached to the solar film, which may cause damage to the solar film. It is recommended that the vehicle should try not to paste or hang things directly on the film within 15 days after the film is applied, so as not to open the gap of the film when the suction cup and paste are pulled up.
I suggest: in order to ensure the best results, the above four precautions must be restrained for a few days after applying the film.
-
1.If you have a sunroof for less than three days, do not open the sunroof when driving, especially at high speeds.
2.After the car is filmed, it is necessary to prevent the windows from being lifted within three days.
3.If the edges of the film are blistered, it should be repaired at the construction site within 24 hours. If the time is exceeded, the glue around the bubble has dried out, and the perimeter of the film cannot be moved, and creases will occur during processing.
4.Don't wash your car for three days.
5.After applying the film in winter, the professional master of the car beauty shop recommends that you do not lift the windows and do not wash the car for a week. It takes about a month for the front and rear gears to dry.
The finch has no Zen to bask in the sun during the day. The most important thing to note is that the backshield electric heating line cannot be opened within a month, because if the dust electric heating line is opened after the film is applied in winter, air bubbles will be generated near the electric heating line, which cannot be repaired, which will lead to unnecessary losses and troubles.
6.It is forbidden to directly apply the super glue label to the film within one month after the film is applied, so as to avoid the separation of the film mask from the glass part.
Car film is applied to car glass to control sunlight and ensure safety. >>>More
1. The practice of combining wet and dry stereotype:
1) The combination of dry and wet setting method is a method used when it is impossible to determine whether the consistency of the film and the curvature of the glass is consistent after dry baking. >>>More
Choose a professional school for learning film, welcome to consult, generally a few thousand dollars can be used to ensure the amount of practical training every day, until you learn. Hope.
Car wrap tool preparation
Explosion-proof film pasting tools mainly include glass cleaning brushes, wipers, wipers, shaping scrapers, utility knives, watering cans, hot air blowers, etc. >>>More
Guangzhou film craftsman auto supplies company, can make dragon film.