How to remove the screws of the whole house custom cabinet of Quanyou Home

All-friends wardrobe 106306 disassembled.

Preparation: A large Phillips screwdriver.

Two sturdy stools that can stand people.

Disassembling and assembling furniture requires the cooperation of two powerful adults. There is a need for top cabinets.

Remove the top cabinet; Remove the door panel. There are latches on the top of the door, hold down the metal post on the latch panel, and pull down at the same time, the door will leave the chute, and there are two latches on each door. While lifting the door up, lift the bottom edge of the door out of the chute and remove the door panel.

Unpack the inner drawer. Pull the drawer out while pressing up on one of the plastic levers in the slides on either side of the drawer, pulling the drawer out as you press. Pull out the thick pad on the side of the drawer to reveal the eccentric screw holes in the upper panel of the drawer.

Remove the side panels. First remove the partition under the drawer, there are four tension bolts below, loosen the front two first, lift the front of the partition to facilitate the observation and loosen the back two (the first two are high and then low during installation, and the first two are flattened after tightening), and then the first two are tightened), and the partition is removed. Place the top and bottom plates close to the side panels of the four eccentric wheels.

The nuts are loosened to the end. The eccentric nuts under the upper panel of the drawer are loosened. The eccentric nuts on the back of the cabinet are loosened near the side panels.

Tap the side panel from the inside of the cabinet to see that the side panel is leaving, and you can't do without it, check the adjacent eccentric nut and loosen it with a screwdriver. Pay attention to translation, the upper and lower rear three sides are separated at the same time, if the house is moved, the bolts do not need to be removed, and they remain in place. Remove the panel on the other side, note that there are five tension bolts in the middle partition to loosen, and remove the left panel after removing the partition wrench.

Remove the top plate. Loosen the eccentric wheel at the top of the back riser and the upper end of the wardrobe center. The two of them lifted the top plate at the same time and moved it out. Be careful not to touch the bolts on the top plate.

Remove the drawer on the cover. Loosen the 4 eccentric nuts under the cover plate on the drawer, lift the outside, pull out the fixing bolts of the cover plate and the partition plate in the drawer, pull it outward, and detach it from the neutral plate.

Dismantle the back panel of the drawer side cabinet. Loosen the connecting nut between the back plate and the bottom plate, lift it, and disassemble the second piece, pay attention to the connection point between the back plate of the drawer and the partition plate of the drawer, take it out after loosening, and loosen the connection between the center plate of the drawer and the bottom plate with the eccentric nut, and take it out.

Dismantle the wardrobe neutral panel. Loosen the eccentric nut with the bottom plate and lift.

Continue to remove the back panel.

Lift the base plate to the target room, leaving 50 cm of installation space around it. Assemble it back in the reverse order when dismantling, pay attention to the bolt insertion when installing, install it in place after alignment, and tighten the corresponding eccentric nut.

Once the installation is complete, push the bottom to move the wardrobe into place.

In the front two corners of the wardrobe, the pads are leveled to reduce shaking.

Be careful not to touch the connecting bolts. When dismantling, one person dismantles and one person supports.

If you want to move over a long distance, you need to take out the connecting bolts and eccentric nuts and wrap them, install and tighten the bolts first, and the eccentric nuts should not be installed first, but be installed and screwed at the back to facilitate the alignment of the notch.

Mark the order and direction before dismantling.

The general whole house custom furniture is fixed with an eccentric lock structure, and you can find the keyhole and directly unscrew it with the plum blossom taper to remove it, which is very simple, in fact, you can also install it yourself.

Hello The general whole house custom furniture is fixed with an eccentric lock structure, and you can find the keyhole directly with the plum blossom taper to unscrew it down, which is very simple, in fact, you can also install it

This kind of screw is now a common connector for panel furniture. To put it simply; It can be understood as a column link, as long as you turn the screw left, it can be easily disassembled, you try it.

You're talking about the one inside? You have to pull the plank out to unscrew it.

3-in-1 Lock: If you look closely at his cross fork, there is a horn that is a little longer and a little sharper.

Lock clockwise and release counterclockwise.

Preferred tool flat screwdriver (keys these are also available).

Regardless of the current direction of the tip, as long as you ensure that you tighten it counterclockwise, screw it to another plate connected by the tip in the direction of the tip, and all the screws can be removed after loosening the plate.

Disassemble with a screwdriver.

Common furniture screws are large flat heads, round heads, flat heads, hexagonal heads, and large flat heads. Large flathead screws, the removal tool is a flathead screwdriver. Round-head screws, removal tool Phillips screwdriver or six-pointed star key.

Flathead screws, removal tools, six-pointed star spoons and Phillips screwdrivers. Hexagonal head screws, removal tool wrenches or hexagonal star keys. Large flat head screws, removal tool flathead screwdriver or Phillips screwdriver.

Since there are many types of furniture screws, the method of disassembly is basically the same, as long as you choose the right tool, you can remove it.

For slippery wire or broken screws, you can use the wire retractor to remove, and you need to operate with a hand drill when dismantling, and the speed should be slow, not too high or suddenly accelerated, and the whole process needs to be reversed. Take one end to open the hole first, and then take the other end out. The specific steps are as follows:

1. Install one end of the wire retractor on the hand drill;

2. Reverse and drill a small hole in the top of the worn or broken screw;

3. Install the other end of the wire retractor on the hand drill;

4. Reverse and take out the screws.

This is a bayonet, you just need to look in the opposite direction to turn, to turn a flat one, the board will fall off as soon as you pull it

Turn 90 degrees to the left. Remove the planks and you're good to go.

This is a lock, not a screw, and it opens when you twist it in one direction.

Is there a cross-shaped screwdriver, turn it a little bit to separate it from the other board, and then insert a chopstick into the hole on the side, and slowly get it out.

1. Cross.

There is generally an arrow on the screw, and there is a protruding screw on another wooden board that is inserted in the special Phillips screw, and then knock it outward, and the arrow is aimed at another wooden board perpendicular to it without taking the screw cap.

2. The screwdriver bit should be selected correctly, not to look almost on, but to try to fit accurately, it is better to use a T-shaped or curved handle style, it is easier to obtain axial force than a straight handle, and of course, it is the fastest to use an electric screwdriver.

The three-in-one connection reduces the use of adhesives, but there is also a problem that is instability, which needs to be nailed to the back panel of the furniture to be stable.

In order to achieve the effect of concealment without leaving gaps, it is necessary to completely knock the embedded parts into the board, so that the three-in-one connector cannot be seen from the outer surface, and it is not easy to have gaps.

The screws of the transverse plate of this kind of cabinet are directly screwed inside the plug and then dragged down.

Question: It is a three-in-one screw, and there is a horizontal section in the cabinet Answer: 1. According to the size of the three-in-one screw, choose the appropriate Phillips screwdriver; 2. Hold the Phillips screwdriver against the eccentric wheel of the 3-in-1 screw, and rotate 90 degrees counterclockwise; 3. After the screw is loosened, remove the eccentric wheel; 4. After removing the plate on the screw, the connecting rod can be removed.

The disassembly process and the installation process can be reversed, but all nuts on the same side must be loosened before they can be removed.

It can be removed directly with a small flat screwdriver.

Isn't it enough to use a Phillips screwdriver?

Summary: How do you disassemble a cabinet fixed to the wall?

To remove the cabinet fixed on the wall, it takes 2 people to cooperate, and one person to lift the corner of the cabinet, the specific operation steps are as follows:

1. A person lifts up a corner of the cabinet with great force.

2. The other person uses a screwdriver to unscrew the screw in the lower left corner.

3. Unscrew the screws in the upper right corner and the lower right corner.

4. Finally, unscrew the screw in the upper left corner, and when screwing, you should also lift the lower left corner of the cabinet to prevent the cabinet from falling.

5. You can remove the cabinet on the wall.

How to remove the cabinet on the wall during renovation?

How do you remove a cabinet fixed to the wall? To remove the cabinet fixed on the wall, it takes 2 people to cooperate, and one person to lift the corner of the cabinet, the specific operation steps are as follows: 1. One person lifts the corner of the cabinet hard.

2. The other person uses a screwdriver to unscrew the screw in the lower left corner. 3. Unscrew the screws in the upper right corner and the lower right corner. 4. Finally, unscrew the screw in the upper left corner, and when screwing, you should also lift the lower left corner of the cabinet to prevent the cabinet from falling.

5. You can remove the cabinet on the wall.

Can my home decoration wine cabinet be dismantled like this?

Yes, as long as it is mounted on the wall, you can use the same method.

But if you look around the wine cooler and you can't find any screws or anything like that, what do you use to fix it? It should be fixed with something, and that is the place where the force is to be borrowed.