Turning on the computer monitor has an effect, but it will soon be gone, yes

Updated on number 2024-08-09
10 answers
  1. Anonymous users2024-02-15

    With the continuous improvement of living standards, some families will have a computer in the family, but many friends have such an experience, that is, the computer at home has been put for a long time, and the monitor will not be able to display. So what should I do if the computer is left for a long time and the monitor cannot be displayed?

    1. First of all, check whether the power supply of the monitor is plugged in well, if the power switch of your monitor is a light touch switch, when you power on the monitor, you should hear a slight one"Crackling"sound, at this time, it can be judged that the switching power supply circuit of the display is good. Is the power switch on the remonitor turned on? Is the monitor's power indicator on?

    When approaching the monitor screen with your hand and slowly move it to see if there is"Sizzle"The sound of the hairs on the hands at the same time.

    There is a feeling of being sucked up, which is checking whether the display high voltage circuit is working properly.

    2. If you are sure that the monitor has been powered on and there is a high voltage generated, continue to check whether the data cable connector of the display is in good contact with the signal output interface of the graphics card and whether it is loose. Unplug it again and check if there is any bent or broken needle or a lot of dirt in the D-connector. This is a problem that many users often encounter, when connecting the D-type socket, the force is uneven, or forgetting to tighten the fixing screw of the interface, so that the interface is loose and causes poor contact, or due to improper installation method or excessive force, there are broken needles or bent needles in the D-type interface, resulting in poor contact.

    3. Finally, check whether the power-on highlight source indicator and the hard disk indicator on the panel are flashing. Because if the host power supply is not working or the motherboard is not powered, the display will not have an image display when it does not receive a signal.

    The above computer has been put on for a long time, and the display can not be called to display the content of the content is introduced, and friends who will not solve it may wish to refer to the methods introduced above.

  2. Anonymous users2024-02-14

    It may be that the monitor is damp and the humidity in the home is too high.

    It was the same when my family first moved, and the screen couldn't see anything for a long time after it was turned on, and it was okay after a while.

  3. Anonymous users2024-02-13

    If it is flat, it may be that the picture tube is aging. LCD to see if it is a response time.

  4. Anonymous users2024-02-12

    Turn the case on and see if the fan turns! If you do, check the signal cable connected to the monitor! Replug, if it doesn't work, pull up the memory, clean the brush, and reinsert! Graphics cards too! Of course, all this after turning off the power!

  5. Anonymous users2024-02-11

    As the problem is described, it is indeed a problem with the display, and now you need to look at two situations to judge the problem, 1 is the display indicator after the black screen, green or yellow and red? 2 is the screen after the screen is black, can you see the faint characters when you look at the screen from the side? If the indicator light is black, there is a problem with the power strip, if it is a green light, and the screen can see faint characters, there is a problem with the high voltage board.

    The maintenance cost of these two kinds of faults is not high, and it can be solved for dozens of dollars.

  6. Anonymous users2024-02-10

    Do you have this kind of problem with your computer and display fully open? That means you're all open, but nothing shows up until the desktop rings? If so, it's the problem of the motherboard It's not very clear if it's a discrete graphics card, if it's this kind of problem, you can enter the motherboard modulation panel when you boot it up, and it should be able to be adjusted, but I don't know too much about the specifics, because it doesn't delay use, and I haven't dealt with this problem.

  7. Anonymous users2024-02-09

    It could be that the boot is slow, which is an issue with the speed of the host

    There is also a kind of thing that is always black, and it slowly lights up and you can see what is displayed, which is the cause of aging, and sometimes the environment is damp

  8. Anonymous users2024-02-08

    It cannot be arbitrarily judged that the computer is broken.

    There are generally several reasons why a computer monitor doesn't show up on your desktop that long after it's turned on:

    1. There are too many system startup items.

    2. Poisoning. 3. The system garbage has not been cleaned up for a long time.

    4. The memory is too low.

  9. Anonymous users2024-02-07

    There is a problem with the software configuration of the computer.

  10. Anonymous users2024-02-06

    Fold the monitor, unplug the wiring and clean it, and plug it back in.

    If you can, you can change the monitor.

Related questions
2 answers2024-08-09

Analysis: There are two situations when the monitor cannot be turned on: the screen is not powered on (the power indicator is not on) or the screen is powered on but there is no signal or "nosighal", the former means that the power is not on or the connection is poor, and the latter is generally the memory module is not in contact or the graphics card is damaged. >>>More

8 answers2024-08-09

Sometimes unintentional operations on the computer desktop. >>>More

4 answers2024-08-09

The internal temperature of the case is too high, the graphics card, the memory, the power supply - will cause a blue screen, crash, the following is a little experience that individuals have summarized in the repair process, you can take a look at the control check treatment. --You can check, clean, replace, memory, hard disk data cable first. >>>More

6 answers2024-08-09

After replacing the computer with a new monitor, the display is blurry and the resolution cannot be adjusted? >>>More

14 answers2024-08-09

This situation has been encountered before, if you uninstall the host, you will find that there is a small red light flashing, this is why a certain hardware in the host is installed, check it yourself. After-sales service**.