-
Anonymous users2024-02-152. After the mobile hard disk system disk is made, the system has a partition software and DOS toolbox, and there are several special partition programs to choose from, provided that the BIOS must set the U disk to start first.
3. To install the system with the user's hard disk, you need to partition it before you can install the system, that is, open the system disk first, select the partition tool to partition, and then go back to the PE disk for system installation. I don't want to make a portable hard disk system disk after partitioning.
-
Anonymous users2024-02-14The production method is the same as the U disk, and there is a tutorial on the official website of U Dangjia.
-
Anonymous users2024-02-13Usually, just follow the prompts. The following takes Xingyu Liyun's PE production software as an example:
2. The following are installation tips, confirm it.
3. Automatically call ghost to install PE and wait for ghost to finish.
4. After the ghost is completed, it will prompt success.
5. Click "Boot Test" to test whether the hard disk can boot.
-
Anonymous users2024-02-121。That tool (like other portable hard drive boot makers on the web) is "Format the entire portable hard drive"!
2.Please be sure to back up the i-disk before you can do it.
-
Anonymous users2024-02-11First use the Windows 7 system into the disk management to move the hard disk two areas or three partitions, the first one is formatted as FAT32. The others are NTFS. Then set that FAT32 partition to active.
Finally open the ISO file with Winrar. Copy all the files inside to the disk where the FAT32 partition is located. Win7PE is recommended
This is the PE of the win7 kernel.
-
Anonymous users2024-02-10Let me talk about my method: I am from the speed of the forum ** of the system installation disk, is *ISO file,Boot with PE inside,Open this file with ultraiso software,You can remove the system installation file inside (I use the ghost version,Put the largest *.
gho file deletion), then select "Start", then select "Write Hard Drive Image", and then select your Chunhong's mobile hard disk (it is best to choose to format it first), provided that your mobile hard disk is empty, because after this write, the hard disk partition and files are all gone. After doing it, use the PE of the mobile hard disk to start the computer, and under the PE system, you can adjust the partition of the mobile hard loss disk without loss, the PE partition occupies about 200-300MB, and you can keep this area larger.
-
Anonymous users2024-02-09One trick to learn to use a USB flash drive as a system boot disk PE
There will be a lot of trouble with your own matching, and there is no after-sales service, it is better to buy an original, the best is Seagate and Hitachi, about 600-800 yuan, it is not bad to buy a Lenovo, about 500-600 yuan (the Olympic commemorative version also sends a bird's nest and the water cube medallion, very cost-effective, ** in 599, very beautiful), Newman's is about 500 yuan. >>>More
Minimum configuration. RAM: 512MB
Graphics card: Support 128M onboard graphics card. >>>More
The most reasonable partition.
120GC disk, 20GB, FAT32 (reason is good for system rate) D disk, 30G, NTFS (put some programs, games, etc., most of them are installed in this disk) E disk, 50G, NTFS (put some large files, movies and songs, etc., NTFS is good for the file system). >>>More
Take out the hard disk in the hard disk box, directly connect it to the serial port board to do the disk, boot to the system, see if you can recognize it, I estimate that there may be abnormal plugging and unplugging The partition table is wrong, if you can recognize it in the system, you can change the hard disk box, you can't recognize it, just start it to DOS Check it with MHDD, it's just a problem with the hard disk partition, you can re-partition the hard disk, and the data inside can be retrieved with easyrecovery or Ender data recovery.
At least at 2g. Isn't he automatically assigned into the system?。。 But your 2G of RAM is enough. >>>More