How to solve the failure of Midea s health pot E1

Generally, the health pot shows that E1 may be a sensor open circuit, and the sensor open circuit includes leads, plugs and sockets, etc. Therefore, it is necessary to check whether the socket and lead wire are normal.

Fault. 1. The temperature sensor of the pot.

Damage (thermistor.)

bad); 2. The main control IC is broken;

3. The oscillating crystal oscillator inside the pot.

Damage; Solutions to the above problems:

1. Replace the temperature sensor, and the resistance value is about 100K;

2. Replace the main control IC, if it is written with a program, you must contact the manufacturer to purchase;

3. The damage straightness of the crystal oscillator is replaced according to the original model, generally 8m crystal oscillator;

If there is a failure of 11 in the health pot of Midea**, it is recommended to contact the after-sales service of the product directly and let the professionals test and repair it.

How to solve the meaning failure of the beauty health pot? You can ask the after-sales customer service or after-sales maintenance personnel, and they will tell you how to solve it, and under normal circumstances, it is best to get after-sales service to solve it.

<>1. The health pot shows that the E1 is faulty** because the sensor is broken.

2. Sensor disconnection: It may be that the sensor is disconnected, including leads, plugs and sockets. The weather is too cold, and the resistance value of the sensor liquid is too high, causing the health pot to display the **. Because its material is high borosilicate glass front glass.

The temperature resistance is low, the temperature is too high and it will break, and the power is generally small, generally around 400w, so the heating time is long.

3. Solution: It is recommended to find after-sales maintenance treatment.

<>1. The health pot shows that the E1 is faulty** because the sensor is broken.

2. Sensor disconnection: It may be that the sensor is disconnected, including leads, plugs and sockets, etc. The space-based talk gas is too cold, and the sensor resistance is too high, causing the health pot to display the ** cover.

Because its material is high borosilicate glass, the temperature resistance is low, the temperature is too high will break, and the power is generally small, generally around 400W, so the heating time is long.

3. Solution: It is recommended to find after-sales maintenance treatment.

The health pot shows that the E1 is faulty** because the sensor banquet device is disconnected.

Sensor Break:

1. It is possible that the sensor is broken, including leads, plugs and sockets, etc.

2. The weather is too cold, and the sensor resistance is too high, causing the health pot to display the **.

Because it is made of high borosilicate glass.

The temperature resistance is low, the temperature is too high and it will break, and the power is generally small, generally around 400W, so the heating time is long.

Solution: It is recommended to find after-sales maintenance treatment.

E1, E2, F2, E6 and other displays appear: this is a fault**, indicating that the electrical appliance is faulty and the approximate location cannot work normally. Since the faults of each appliance are different, you can take a look at the manual first.

There is generally a fault ** table in it to see if there is such a fault and the corresponding fault prompt. If you can't find it, or there is no manual, you can contact the after-sales service. If the warranty period has passed, or you do not have professional maintenance knowledge, and you do not have the same accessories, you can ask the electrical repair shop to check and repair it.

FYI.

The e2 failure method is as follows:

1. During the heating process of the water heater, the safety valve.

There are water droplets dripping out of the holes. Close the water inlet valve and change the knob of the mixing valve to a high temperature to avoid the leakage of the single-flush bidirectional safety valve, so that the water drips out of the shower. If the mixing valve is not installed, the hot water ball valve can be opened a little to relieve the pressure of the flowing water, which can also avoid the leakage of the one-way safety valve.

2. Leakage of electricity during the use of the water heater. Adjust the air pressure switch to the appropriate position. Adjust the suction nozzle. Plug in or replace the silicone tubing. Replace the air pressure switch. Replace the pulse.

3. The heating indicator light is not lit and cannot be heated. Check for exclusions. Replace the thermostat.

E2 is because the electronic water inlet valve of the health pot is broken, for the health pot of Dan Zhizhi, E2 is a dry mold sensitive burning, it is recommended that the user take the health pot away from the base, unplug the power supply, and then refill the water after the pot body cools down.

After excluding the above factors, it is recommended that users contact the after-sales service in time for relevant testing.

E2 is the phenomenon of dry boiling, you can take the pot body away from the base, unplug the power supply, until the pot body cools down, and reuse it with water.