-
The first cause of hollowing of wall tiles is the problem of the base layer of the wall. Because all our tiles are glued to the walls. The wall base is basically plastered, if the strength of the plastering layer wall is not high, there is a phenomenon of sand falling sand, or there is a hollow drum in the plastering layer, then the result at this time is that the tiles will also be hollow after pasting.
-
Maybe it's because the master doesn't care. The master didn't do a good job when he pasted that wall, so it caused the drum to be hollow. It may also be because there is a problem with the base layer of the wall built by the developer, so this phenomenon is caused.
-
1. The coating of cement should be uniform and full, just falling to the sinking and solidifying, it is often easy to appear hollowing, which will help the caulk will not turn black immediately in the later stage.
2. Measure the horizontality and verticality of the tiles. Especially when paving wall tiles, it is best to measure each layer of paving. Cement mortar should fill the gaps on the four sides!
Special attention should be paid to the fact that when the back of the tile is full of mortar, it should be plastered into a hypotenuse on the four periphery of the tile, leaving some gaps in the middle, so that when pressing, tapping the tile, full, the most important part is often the four sides of the brick The paving method of the tile is actually very simple, and whether it is empty or not depends entirely on it.
3. The cement mortar should be wiped evenly! But the simpler it is, the more detailed it is, the more problems will arise. After the wall tiles are pasted on the wall Tongfan Lao, it takes some time for the cement to solidify.
4. The ceramic tile paving method is actually very simple, there will be sinking and solidification, so the key link is at the upper end of the wall tile. However, the details of paving are often easy to be overlooked, and the cement is evenly applied at the upper end of the brick to avoid hollowing. On the question of caulk, it is best to pave a piece of masonry and let it wipe the cement mortar of the brick joint immediately to keep it neat and beautiful.
5. Wipe the cement mortar of the brick joint clean to avoid adding the grout to black, which often makes many people too negligent, and the four sides of the tile groove should be filled with cement to saturate.
-
What is the problem of empty wall tiles and walls: the reasons for the empty wall tiles and walls are as follows: construction technology. Before paving the wall tiles, it is necessary to use cement mortar to climb and then compact, and then to pick up the bricks and fill them with cement oil.
However, due to carelessness, some masters did not beat the cement in the process of climbing and compacting the environment and season. Due to the change of seasons, the ambient temperature drops sharply, and if the paved wall tiles are not completely dried in the cement slurry, the water in the mortar will be completely drenched.
-
Why is the wall tile pasted by the master not empty on three walls, and one wall is completely empty? When decorating, my home tiling master has not finished pasting"Strikes"Why is there an empty row on the wall, and it is not pasted in one go? I don't think that whether you paint or tile the wall, you should finish the whole wall together?
How can there be a reason to decorate the wall without painting or tiling!
The master who put the brick looked at me quietly and said, and finally I used Song Xiaobao's words"Please give me a perfect explanation"!The master laughed when he heard this, and explained that there was a hidden doorway here. At first, I thought it was a wall tile that had to be cut, but it was missed.
It turned out that I had misunderstood, if an insider took a look, he would definitely know that this was an invitation to the master, and the brick master deliberately left it blank.
When I decided with the designer to determine the decoration plan, I chose to lay wooden floors on the ground at home, and the master said that he had an empty strip under the wall that was not pasted mainly because of the wooden floor (considering the humidity of the bathroom, the bathroom used wood grain bricks instead of wooden floors, so that the integrity of the ground is still unified)!
Because wood flooring and ceramic tiles are two completely different decoration materials, but wall tiles and wooden floors must always be connected. The master said that in order to close and connect the two materials better and more beautifully, this is the time to paste the wall tiles, deliberately vacate a row, and then lay the wooden floor first, and then cover the wall tiles on the floor, and then close the edge with a baseboard.
Actually, this can be said to belong"The wall is pressed to the ground"The way of laying. This method has relatively high requirements for the tiling master, and the process is relatively complex and time-consuming, but in this way, the gap between the wall and the ground is very small, and it is more beautiful. If the bathroom walls and floor tiles are laid in this way, the waterproof effect is also better.
I didn't expect my family to invite a master, stealing fun! If you also decide to put tiles on the walls of the new house and lay wooden floors on the ground, you must pay attention to whether the master leaves a row of tiles under the wall first!
-
It may be that there is a problem with the base layer of the wall built by the developer, so this phenomenon is caused.
-
It may be that if you stick it this way, you can make the gap between the wall tiles smaller.
-
Because the master doesn't care. The master didn't do a good job when he pasted that wall, so it caused the drum to be hollow.
There are many reasons for the hollowing of ceramic tiles, decoration and pasting tiles, high requirements for auxiliary materials, pasting ceramic tile auxiliary materials, not suitable for ceramic tile materials, low indoor temperature, non-standard operation of workers, and not pasting tiles in accordance with the process order, all of which may cause the tile hollowing to fall off. The hollowing is caused by the presence of air in the original masonry and the plaster layer. Hollow drum mostly appears in one or more of the four corners of the tile, we are very simple when checking, only need to use a small hammer or hard object to knock the plastering layer and leveling layer, listen to the sound to distinguish, you can knock on the middle or four corners, can determine whether the hollow drum. >>>More
There is no inevitable relationship between waterproofing and tiling, so there is no need to say that waterproofing tiles will be more stable. If you want the tile to be more stable, you still need to start with the material of the tile. >>>More
Personally, I think the horizontal stickers look better.
The bricklayer master said that the balcony tiles cost labor and bricks, and other alternatives are to change the anticorrosive wood to make the balcony more beautiful. The ground covered with antiseptic wood will be much warmer and closer to nature. When friends come to the house to party and play, they feel comfortable. >>>More
It can last for three to five years;
Its practical adhesive tiles are faster than cement tiles, and firmer than cement tiles; >>>More