Samsung S6 how to set up mobile network

If your phone needs to use mobile data to surf the Internet, here's how:

Pull down the top curtain of your phone, tap [Mobile Data] and [Data Connection] to make it green to indicate that it is on.

If you are unable to access the Internet with data data, we recommend that you try the following steps:

1. Check whether the SIM card is enabled for GPRS Internet service or temporarily closed.

To use the mobile phone data Internet function, the ** card needs to activate the data data Internet service. You can contact the local network provider of **card** to open the data traffic Internet service.

2. Check whether the "Mobile Data" switch is turned on.

Slide your finger down on the top curtain of the screen and turn the "Mobile Data" dot green.

3. Please try to replace it with another ** card.

4. You can also try again in a different time period or network environment.

5. Back up your phone's data (**book, SMS, **, etc.) and restore your phone to factory settings.

If the fault persists, it is recommended to send the phone to the nearest Samsung service center for testing and repair.

1. Check whether the SIM card has opened GPRS Internet service or has been temporarily closed, use the mobile phone data Internet function, ** card needs to open data traffic Internet service, you can contact ** card's local network * business to open data traffic Internet service.

2. Check whether the mobile data switch is turned on, slide down the top curtain of the screen with your finger, and turn the mobile data point green.

3. Please try to change other ** cards, or try again in a different time period or network environment.

1. The first inspection state first determines that the mobile phone is not in arrears, and the data function of the mobile phone cannot be used in the case of arrears.

2. Make sure to turn on the data function of the phone, pull down or go to the settings to find the mobile data, and turn on the electrodes.

3. Make sure that the location is covered by mobile data network and has a strong signal strength, if the signal is poor or there is no network, the data network function cannot be used.

1. S6 includes G9200, G9208, and G9209: G9209 does not support VoLTE service;

2. G9208 and G9200 need to be upgraded to the latest version to support VoLTE service;

3. Turn on the Volate function, find the call of Volate on the mobile network in the phone settings, and check it.

Specifics of the Samsung Galaxy S8:

1. Samsung Galaxy S8 is a new generation of smartphone products launched by South Korea's Samsung, which was unveiled at the MWC exhibition in February 2017.

2. Equipped with 10nm Snapdragon 835 and Exynos 8895 processors, there are two sail versions: inch and inch. Full Netcom, fingerprint recognition, dual-band WiFi, Qualcomm Snapdragon, GPS navigation.

3. On the evening of March 29, 2017, Beijing time, Samsung released the 2017 flagship mobile phone sedan Galaxy S8 in New York, and the first sail opened for pre-order on March 30, 2017.

2. Access point information liquid.

3. Finally, press the menu button, and then press Save to save.

WAP is the name of the access point used by mobile phones to access the Internet. Only WAP** celery can be accessed through CMWAP. CMWAP uses the HTTP** protocol and the WAP gateway protocol to access the Internet.

S6: To set up the network switch between 2G 3G and 4G, you can turn on Settings - Connect - Mobile Network - Network Mode SIM1 SIM2-4G 3G 2G (Auto Connection) or 3G 2G (Auto Connect).

Note: Two cards cannot use 3G or 4G network at the same time, if one card is set to 4G 3G 2G (auto-connect) or 3G 2G (auto-connect), then the other card will automatically change to 2G network only.

In the earlier versions of the G9200, only card slot 1 supported CDMA cards, and after upgrading to the latest version, card slot 2 can also use telecom cards. If one card slot is inserted into a telecom card, the network mode cannot be switched, and the other card slot only supports 2G network.

Only when using a mobile card, it supports changing the network mode, and China Unicom card only supports 2G network;

Network mode switching is not supported, and slot 2 only supports 2G networks.