What should I do if I reinstall the system 0xc000000f?

0xc000000f error will directly fail to boot, you can't enter the system, and if you don't fix it, the computer will be paralyzed. So what is the cause of this 0xc000000f error, there are three main reasons:

1. The system boot file is corrupted.

2. The MBR boot is damaged or missing.

3. The partition table is lost and the boot cannot be booted.

Solution: 1. Make a USB flash drive boot disk through Xiaobai's one-click reinstall system tool, and the specific tutorial can be found in [Xiaobai System Official Website].

2. Use the U disk to boot into PE, and open the Diskgenius partition tool on the desktop. We select our computer's hard drive and click on "Rebuild Master Boot Record."

MBR)", and then wait a few moments to fix the system.

Method 2: For partition loss.

Method 3: Fix the boot.

We open the Xiaobai installation tool on the PE desktop, click on the boot repair in the upper function bar, and click "Repair" in the pop-up boot repair tool.

After repairing the system boot, we restart the computer and see if we can fix the black screen.

Issue. If you can't, choose to reinstall the system again.

Hello, here's why:

If the system installation fails, you can directly reinstall the system with a verified system disk, so that you can automatically and smoothly solve the problem of system installation failure and failure to start. These are possible with a USB flash drive or hard disk, and the installation speed is very fast. But the key is:

It is necessary to have a system disk that is compatible with IDE, ACHI, and RAID mode installation and can be automatically and permanently activated, and can automatically install the machine hardware driver sequence, so that the system can be automatically and smoothly reinstalled throughout the process.

1. Error**0xc00001 usually means that there is some problem with your device or that the boot file is corrupted.

2. It is also possible that there is a problem with the related software, so you can try to uninstall the problematic software at this time.

3. Restart the computer first, and press and hold "shift+F8" at startup to open the recovery interface.

4. Then select Advanced Options - Troubleshooting - Startup Settings - Restart in the interface.

5. After waiting for the computer to restart, enter the startup settings menu, and select "Safe Mode" at this time.

Just start it. 6. Finally, select Settings in the start menu in the lower left corner, select "Apps & Functions", uninstall the recently installed software, and then restart it.

Method Steps:

1. First of all, after this situation, we need to re-enter the Douhe Yudan into the PE system, in the PE system, press the combination key Win+R to open the running window, enter cmd and press enter to bring up the command prompt, as shown in the figure:

2. Then execute the following commands in turn:

c:cd c:\windows\system32\bcdedit /set osdevice bootbcdedit /set device bootbcdedit /set detecthal 1<>

3. Restart the computer to see if it can enter the system normally, if the problem persists, repartition and reinstall the system again.

Summary. How to solve the 0xc0000098 when the reinstallation system occurs? Hello dear, go into the PE system and replace that file if it won't you can 1Reboot,Press F8 without stopping during startup (no need to put win7 disc)

2.Select "Repair Computer" (the same meaning is immediate, I don't remember much about the specific project name).

4.Fix the interface and select Command Prompt

5.Type bootrec rebuildbcd (note the spaces).

6.If Bootrec runs successfully, you will see the system installation path, in this case, select the system into BCD.

7.If bootrec is not successful, the next step is to delete and rebuild the BCD.

Again, enter the following commands in the interface.

bcdedit export c: bcd backup enter.

ren c: boot bcd enter.

bootrec rebuildbcd enter.

8.Reboot and see the effect.

How to solve the 0xc0000098 when the reinstallation system occurs?

I've seen your question and I'm sorting it out, so please wait a while. <>

How to solve the 0xc0000098 when the reinstallation system occurs? Hello dear, go into the PE system and replace that file if it won't you can 1Restart, keep pressing F8 during startup (no need to put in win7 disc)2

Select "Repair Computer" (the meaning is the same immediately, I don't remember the specific project name) 3Select the language and keyboard (the fix below starts an automatic search for the system you have installed), select the system you want to repair4Fix the interface and select Command Prompt5

Type bootrec rebuildbcd (note the spaces)6If bootrec runs successfully, you will see the system installation path, at this time, select the system into bcd 7If bootrec is not successful, the next step is to delete and rebuild the bcd, also enter the following command bcdedit export c:

bcd backup return ren c: boot bcd return bootrec rebuildbcd enter 8Reboot and see the effect.

If my answer is helpful to you, please give a thumbs up (in the lower left corner), I look forward to your like, your efforts are very important to me, and your support is also the motivation for my progress. If you feel that my answer is still satisfactory, you can click on my avatar for one-on-one consultation. Finally, I wish you good health and a good mood!