What is the reason why the electrostatic precipitator still shows an open circuit after it is replac

Updated on technology 2024-08-13
18 answers
  1. Anonymous users2024-02-16

    After the electrostatic precipitator is replaced, it still shows an open circuit, and the explanation is not the main reason for its problem, it should be that the line of your machine is faulty, that is, it is not closed. So you should use a multimeter to straighten out their lines.

  2. Anonymous users2024-02-15

    The reason why the electrostatic precipitator still shows an open circuit after replacing it may be because it is not the reason after you replace it, even if you replace it, it will still show this, probably because it is a problem with the motherboard.

  3. Anonymous users2024-02-14

    The vacuum cleaner vibrates very badly, and it shows an open circuit after replacement, because connecting the power cord will not cause this prompt to appear. ,。

  4. Anonymous users2024-02-13

    According to your description, the reason for this is that after the equipment is replaced, the circuit is guaranteed to be unblocked.

    We need to check the wiring, and there should be a line connected to the switch.

  5. Anonymous users2024-02-12

    Someone really hit a seven-fold discount or a hand-controlled change after the head is displayed, what is the reason for the open road? It could be that the contact is not good, or it is the cause of the malfunction that causes this condition.

  6. Anonymous users2024-02-11

    It becomes a device to hit seven, and it still shows an open circuit after replacement, if there is a reason, you can install it specifically, and there is a certain error that will lead to this situation.

  7. Anonymous users2024-02-10

    After the dissuasion dust rapper is replaced, it still shows an open circuit, what is the reason why his display is open may be that he did not convert it, and he did not turn a converter.

  8. Anonymous users2024-02-09

    The electric pump of the electric car or the sound of the mobile phone is that the contact between them is not good, and it will be better to reconnect it if there is a problem.

  9. Anonymous users2024-02-08

    It is not a problem with the rapper, it is necessary to check the inside of the electric field after a power failure.

  10. Anonymous users2024-02-07

    It shows that the open circuit should be ignored as long as it works properly.

  11. Anonymous users2024-02-06

    Electromagnetic rapping controller, electromagnetic rapper, hammer, rapping rod, high-voltage isolation switch, damping resistor, high-voltage porcelain bottle, pressure-bearing insulator, conical insulated shaft,

  12. Anonymous users2024-02-05

    What is the reason why the line diagram vibrator still shows an open circuit after being replaced? You should ask a professional to take a look and find out.

  13. Anonymous users2024-02-04

    This suggestion is that you specifically search for the specific question you want to ask, there is a specific explanation above, you have the relevant ** for you to choose and reference, if it still can't be solved, you can play this. The after-sales service of the product can also be consulted by the manual customer service, and you can also get the corresponding maintenance and after-sales service points to deal with it.

  14. Anonymous users2024-02-03

    The shop rented into a vibrator after the replacement still shows an open circuit, what is the reason, I think this reason is the reason for the motherboard.

  15. Anonymous users2024-02-02

    If the rapper of the electrostatic precipitator still shows an open circuit after being replaced, I think this reason is very obvious and must be done again.

  16. Anonymous users2024-02-01

    His follow-up number may be because his original route was not so good and could be started.

  17. Anonymous users2024-01-31

    It's usually a hardware failure.

    It is recommended to go to the official after-sales inspection and repair.

  18. Anonymous users2024-01-30

    Maintenance measures for the rapping device of the electrostatic precipitator:

    1. Check the radial deviation of each rapping system, and adjust the position of the bearing seat, rapping motor and reducer accordingly according to the specified conditions.

    2. Check the rapping bearing seat, replace the friction wearing parts, and calibrate the level and center of each bearing seat of the same transmission shaft, and adjust it if it exceeds the standard.

    3. Disc or open the rapping device to check each axis, and adjust or replace the shaft if it is beating or stuck.

    4. Check the centerline of each axis of rotation.

    5. Check the vibrating universal coupling, flange, connecting bolts, spring washers, and replace damaged parts.

    6. Check the U-shaped screw of the hammer and replace it when it is seriously worn.

    7. Check the connection of the rotating arm of the rotating hammer.

    8. Check the vibrating hammer head and replace the vibrating hammer that cannot be repaired.

    9. After reloading, observe the rotation of the crank.

    10. Inspect and replace the rapping fuse or pin.

    Ten. 1. Check the part where the rapping shaft penetrates the wall and replace the seal with serious air leakage.

Related questions
11 answers2024-08-13

Principle: Dusty gases pass through a high-voltage electrostatic field. >>>More

8 answers2024-08-13

Compared with other dust removal equipment, the <> electrostatic precipitator has less energy consumption and high dust removal efficiency, which is suitable for removing 0 01-50 m dust in the flue gas, and can be used in the occasion of high flue gas temperature and high pressure. Practice has shown that the larger the amount of flue gas processed, the more economical the investment and operating costs of using the electrostatic precipitator.

9 answers2024-08-13

Dust collector equipment can be divided into two categories: Dry dust collector equipment: inertial dust collector, electrostatic precipitator, bag dust collector, cyclone dust collector. >>>More

4 answers2024-08-13

From the description, electrostatic precipitators are often used in exhaust gas treatment equipment, and their principle is to use the principle of electrostatic action to capture dust equipment. It has the characteristics of wide application range, high dust removal effect, low equipment resistance and low energy consumption, and can handle large air volume flue gas. In the actual exhaust gas treatment process, the dust removal effect of the electrostatic precipitator will decrease, so that the exhaust gas discharged cannot meet the standard, so what is the reason? >>>More

5 answers2024-08-13

1. Reasons for the reduction of dust removal effect:

1.The anode plate is spaced, the discharge field is small, the dust collection efficiency is low, the exhaust gas resistance is large, and the third electric field is cut off during operation. >>>More