How to thaw the washing machine, what to do if the washing machine at home freezes

1.When the water pressure is normal, please check the inlet valve filter for foreign matter?

The cleaning method of the inlet valve filter is as follows:1. Turn off the faucet, turn on the power, press the Start pause button to drain all the water from the hose.

Then after turning off the power, unplug it. 2。Unscrew the end of the water inlet pipe connected to the washing machine, and gently remove the water inlet valve filter inside the water inlet with small tweezers or small pliers with a needle-nosed tip.

3。Put the removed filter in running water, use a toothbrush to remove foreign matter such as rust and iron filings from the filter screen, install it, install the water inlet hose, and check whether the water can enter the filter.

2.Is the faucet on?

If the water level does not reach a certain level for a long time during washing, an IE error will be displayed**, and if the faucet is closed, turn it on.

3.Is the water pressure low?

If the water pressure is low, the flow of water into the washing machine will be smaller, and the time to receive water will be longer, and the washing time will be longer. If the water pressure in the user's home is significantly low, and the minimum water level is not reached for 8 minutes or the water level set after perception for 25 minutes, please repair the water pipe and connect a booster pump.

4.Is the washing machine used in external spaces such as balconies during the cold winter months?

In cold weather, if the washing machine is installed outside the house, the water in the inlet hose will freeze and it will not be able to enter the water. How to thaw the inlet hose Pour warm water of about 50 degrees Celsius on the faucet and connector to thaw it, and unplug the inlet hose. Remove the inlet hose from the washing machine and thaw it in warm water.

There will also be residual moisture on the filter screen of the inlet valve inside the washing machine, so use a hot towel or hair dryer (15cm distance) to thaw the inlet of the water inlet. Then install it and try again to see if the water inlet is normal.

de washing + spinning light flashing.

The folding lid is faulty, is the folding lid covered?

1.Please check that the folded lid is properly coveredIs there something caught in the fold of the lid 3Check whether the magnet in the middle of the fold lid is missing.

Washing machine failure**:

F1: Poor contact with the water level sensor.

E1: When the drainage is overtimed, check whether the drainage pipe is blocked.

E2: The lid is not properly covered.

E3: Unbalanced dehydration, shake the clothes back up and dehydrate again.

E4: When the water inlet is overtime, check the water pressure and whether the water inlet valve is dirty and blocked.

E5: The water temperature is over 50 degrees.

Hello, just pour some hot water and go down.

It's the fastest to use boiling water, I've tried it, and you can shake the water when you thaw it!

1. Cut off the power of the washing machine. The first thing you should check is that the power supply of the washing machine has been disconnected to prevent accidental electric shock during the thawing process. After all, personal safety is the most important thing.

2. Cut off the water inlet pipe, and open the water outlet pipe at the same time to drain the remaining water in the washing machine. At the same time, if there is crushed ice in the washing machine, it should be removed as much as possible.

3. Move the washing machine to a place with a higher temperature, such as a balcony or a warmer place with stronger sunlight. If it is not urgent, it can be left for a longer period of time to allow the ice inside to melt naturally. This method generally does not cause damage to the components.

4. You can also take the method of rapid thawing, first close the outlet valve, and then pour boiling water into the frozen place to make the ice cubes melt quickly. Although this method is simple, it must be noted that you must be cautious when pouring boiling water to avoid a large amount of boiling water causing the tank to rupture due to rapid expansion.

Start by cutting off the power to the washing machine. Check that the power supply of the washing machine has been disconnected to prevent electric shock during the thawing process;

Cut off the water inlet pipe. At the same time, open the water outlet pipe to drain the remaining water from the washing machine. At the same time, if there is crushed ice in the washing machine, it should be discharged;

Carry the washing machine to a place with a higher temperature. For example, put it on a balcony or a warmer, sunny place. Leave it for a longer period of time for the ice inside to melt naturally.

It is also possible to take the method of rapid thawing, first close the outlet valve, and then pour boiling water into the frozen place to make the ice cubes melt quickly. When pouring boiling water, pour it slowly to avoid a large amount of boiling water causing the box to rupture due to rapid expansion; When the water cools, open the departure valve and drain the cold water.

Washing machine:

Washing machine is a cleaning appliance that uses electrical energy to produce mechanical action to wash clothes, and is divided into two categories according to its rated washing capacity: household and collective.

China stipulates that the washing capacity of less than 6 kg belongs to the household washing machine: the household washing machine is mainly composed of a box, a washing and dehydration bucket (some washing and dewatering buckets are separated), transmission and control systems, etc., and some are also equipped with heating devices.

Washing machines generally refer to the use of water as the main cleaning liquid, as opposed to the use of special cleaning solutions, and the dry cleaning that is usually carried out by a dedicated person.

Washing machine cleaning method:

Ask professional maintenance workers to disassemble the washing machine tank for cleaning, which is more expensive and troublesome;

Use a professional washing machine tank cleaner with high sterilization rate for cleaning, decontamination and sterilization are completed in one step, and the operation is simple and effective.

Where is the washing machine frozen?

Is the water not drained after washing or is it an inlet pipe?

You can add warm water below 50 degrees Celsius to the washing machine and soak it.

The following methods can be used:

1. Add some hot water to the washing machine, turn on the drain function, and it will melt after a while.

2. Turn on the electric heaters and other heat dissipation devices in the room where the washing machine is placed. After the room temperature rises, it will thaw over a period of time.

3. After soaking the scrubbing cloth in hot water, cover it on the frozen drain pipe and thaw it after a while.