Telecom optical broadband line does not use dial up broadband Oh, wireless router wifi how to set 10

Telecom Optical Broadband Line Broadband Router Setup Without Dial-up:

1. Enter the router address, connect the wireless router, enter the address you see on the router in the browser, generally of course, if your home is using ** online network, then you need to prepare an additional modem, commonly known as "cat").

2. Enter the corresponding password, and after entering, you will see that you have entered the corresponding account and password.

3. Select the Setup Wizard, and then enter the operation interface, you will see a Setup Wizard on the left, and enter (generally pop up automatically).

4. Enter the Internet mode setting and set the interface of the wizard.

5. Click Next, enter the Internet access method settings, we can see that there are three Internet access options, if your home is dial-up, then use PPPOE. Dynamic IP can be used by plugging the computer directly into the network, and there is a DHCP server on the upper layer. The static IP is generally a private line or something, or it may be a cell bandwidth, etc., and the upper layer does not have a DHCP server, or wants to fix the IP.

I chose PPPoE because I dialed.

6. Enter the password, choose PPPOE dial-up Internet access to fill in the Internet account and password, this should be understood by everyone, there will be an account number to open broadband, fill in it OK.

7. Set the password of the router, and then enter the wireless settings after the next step, we can see the channel, mode, security options, SSID, etc., generally SSID is a name, you can fill it in casually, and then the mode mostly uses 11BGNFor wireless security options, we need to choose WPA-PSK WPA2-PSK, which is so safe that it will not be hacked and rubbed by the network.

8. The next step is to set it up successfully.

9. Click Done, the router will automatically restart, at this time you should wait patiently. The interface that appears after success.

10. How to connect the mobile phone to wifi is simpler, when your router is set up, click the menu key of the mobile phone, and then enter the mobile phone settings, the first item is wifi, and then you set it to on, click to enter the wifi list, select the wireless network name set in the router before you, and enter the password set before to connect.

Directly connect the line from the optical modem to the WAN port of the wireless router, and then connect the route according to the requirements of the wireless router's manual, generally the first time you connect, a prompt will pop up to set it, or directly enter the router settings in the address bar, click the setup wizard, step by step, select automatic selection when selecting the Internet mode, select dynamic IP in the WAN port settings, and then the others are default. You try first, and then come to me if you have questions.

According to your description: Don't set up the light modem, that one can only be used if it is cracked. You can buy a wireless router and connect it as follows.

After connecting, set it up according to the manual, and if yours is an optical network, set it to a static IP address.

If you have any questions, you can consult the staff in the online business hall of Anhui Telecom, and Anhui Telecom has officially opened 4G services. You can go to the online business hall to check the details, I wish you a happy life!

Many users who use telecom modems feel that it is too troublesome to dial up all the time, and want to change the way to access the Internet in a simpler way. I have sorted out for you the setting method of the telecom optical modem without dial-up Internet access for your reference and reading!

How to set up a telecom optical modem that does not need to dial up to access the Internet

1: The optical modem LAN port 1 network cable is connected to the router WAN port, and the computer LAN port network cable is connected to any one of the router LAN port 1234, and then the power is turned on and the computer is turned on.

1. Before setting, the first thing is to connect the data cables of the broadband router, first connect the optical fiber interface, then the ** interface, then the back 3 network cable interfaces, and then the power cable interface.

2. After connecting, open your computer, open the browser web page, and then enter the IP address, by default, you can check the IP address of the computer network. Right-click on the wireless network, click to open the Network and Sharing Center, find the wireless network, and then click on the details, and you can see the IP address.

3. After opening, on the pop-up interface, enter the username and password: telecomadmin password: ne7ja%5m. Once inside, click on Broadband - Internet.

4. Then click Network, Broadband Settings, click New on the right, select Route mode, remove all the checks in the binding options, fill in your broadband and password, and confirm to save.

5. Finally, click WLAN settings, set the WiFi name, WiFi password, security encryption method, as shown in the figure, after setting, click Save, wait for the router to restart, and then you can connect to the Internet.

The telecom optical modem is connected to the wireless router, and the router is dialed up, so that the router is set up and installed

1. Plug in the wireless router and don't pick up the cat first.

2. Connect the computer to any LAN port of the wireless router.

3. Enter the gateway address of the router (on the label behind the router) in the address bar of the browser to enter the settings page.

4. Set it according to PPPoE (ADSL virtual dialing).

5. Set the SSID, encryption method and password again.

6. Save and restart.

7. After setting, connect the network cable from the cat LAN port to the WAN port of the wireless router.

After connecting, log in to the home page of the router,,The username and password are admin by default,Just set the dial in the home page,The second or third item is set to dial。

It must be set up by the telecommunications office, because the fiber will use static IP and dynamic IP

It's the kind that you have to check the frame list of the telecommunications bureau to know, and you don't know how to make it yourself. Ask them to help you get it.

Directly set a fixed IP address to surf the Internet, as long as the optical fiber is not dial-up, there is a fixed IP address.

The router is also dialed to the optical modem, and it must not be without the optical modem.

Since you don't need to use a broadband connection to access the Internet, it means that your cat is a cat with a route, if you connect to the wireless router, you need to choose a dynamic IP mode to get the IP, if the router address is the same as the cat, then you need to change the router LAN port IP, you can change it to, if there is no automatic refresh after the change, you need to log in again with the new address, turn on DHCP, and set the wireless name and password. If you are connected to the LAN port of the router, then enter the router settings first, turn off the DHCP, set the wireless name and password, so that the setting is complete, and then you connect the network cable to the LAN port of the router, you must set it up and then connect the network cable, otherwise you enter the cat instead of the router.

Fiber-to-the-home without dial-up, how to connect the optical modem to the wireless router:

1.Connect the WAN port of the router to the LAN port of the optical modem with a network cable, and when the WAN port light of the router flashes, the connection is normal.

How to configure a wireless router:

1.The system is connected to the router.

Turn on the wifi of the computer, search for the default wifi name of the router (the nameplate on the back of the router is written), and connect to the wifi network. The first time you use the router, you generally don't need to enter the wifi password.

2.Go to the gateway page.

Open a computer browser and enter the gateway IP address of the nameplate on the back of the router (generally, enter the gateway configuration interface. (This interface will pop up automatically for new routes).

3.Set up a way to access the Internet.

Go to the WAN port settings in Advanced settings. Select DHCP Auto Acquisition.

4.Set the wifi name and password.

Go to Wireless Security in the Wireless Settings and select WPA2-PSK mode for Security Mode. Select AES for WPA encryption rule. Set up a wireless network key. The router will automatically restart after setting, please enter a new wifi password to connect.

Hello, Anhui Telecom will answer for you.

Hopefully, the following will be helpful to you.

1.Connect the devices as shown in the following figure.

2.Go to the router and set the routing IP address to This is done in order to stagger the same IP range as the modem.

3.Set the username and password for routing dialing, enable the wireless function, set the wireless password, and enable the DHCP function.

We will inform you of the latest preferential activities through Anhui Telecom's online business hall and official Weibo as soon as possible.

Hope mine can get yours.

If you don't connect the modem, you can directly enter the route, set the routing gateway to, and then use this gateway to enter the route again, clone the network card MAC, and then connect the telecom line to the WAN port of the route.

Whether a telecom optical fiber installation router needs to dial up depends on what kind of equipment the optical fiber is connected to.

1: The optical fiber is connected to an ordinary cat, and the network cable is directly connected to the computer, and the computer dial-up connection is required

Set the router WAN port parameters to PPPoE dial-up mode, and enter the broadband account and password, and set other settings according to the router manual or according to the router setup wizard. After the settings are complete, use a network cable to connect the modem to the WAN port of the router.

2: The optical fiber connection device is a GPON device integrated with the cat and the router, and the computer directly connects the cat without dial-up connection from the computer, and the computer can be connected to the Internet by automatically obtaining the IP

Set the WAN port parameter of the router to dynamic IP, and pay attention to modify the IP address of the LAN port, so as not to be in the same IP segment as the IP address of the modem to avoid IP conflicts. For example, if the IP address of the cat is changed to the first three digits of the LAN port of the router, at least one of them cannot be the same as the first three digits).

Other settings can be set according to the router manual or according to the router setup wizard. After the settings are complete, use a network cable to connect the modem to the WAN port of the router.

3: Fixed IP Fiber Optic Transceiver Case:

Connect the computer network cable to the LAN port of the router, log in to the router settings interface, and set it according to the router manual or the setup wizard. Note: Set the static IP of the router WAN port (some routers have a fixed IP), and enter the IP, subnet mask, gateway, DNS and other relevant information given by the operator when applying for broadband.

After the setup is complete, connect the optical transceiver to the WAN port of the router with a network cable.

Actually, you just change the router settings. The router dynamically obtains the IP address instead. That's it.

First of all, your wireless router is a level 2 router, I encountered your problem before, here are the steps, I will send you the **.

Wireless router settings.

1. First, connect the network cable to the WAN port of the router according to the manual, and then connect the LAN port of the router with the computer with the network cable. Turn on the computer, open the Internet Explorer, enter or, enter the username and password admin in the address bar (both are the same).

2. After entering the route, select the setup wizard, then select ADSL connection, enter your account and password at the router WAN port, if it is a static IP of telecommunications, select static connection, which is generally given to the account and password; Then save! After the router restarts, go to Routing, select Wireless Network Settings--- Turn on Wireless, Turn on Broadcast--- then Wireless Security Settings --- you select the frequency band WEP, WAP WAP2, WAP-PSK WAP2-PSKIn any of these mid-bands--- just enter your own password!

Save --- restart routes! Get!

3. Note that your window7 wireless connection must match the frequency band you choose, otherwise you won't be able to access the network even if you connect!

1. After the installation of the fiber broadband router, you need to set up the router immediately.

2. The setting method is: turn on the router power after connecting the router. Then open the IE browser of the computer, enter in the search bar and press the enter key, you can enter the router settings page. Press Next all the way to finish.

3. It is worth noting that the page for entering the account needs to enter the default admin. The next page is the username and password, which should be given by the dealer and must be entered accurately. to complete the setup process.

4. After the setting is completed, you can log in to the broadband normally. The first time you log in to broadband, you need to enter your username and password once. There will be no need for this process in the future.

Hello, welcome to use China Telecom products, 1 first determine whether the uneasy wireless network is normal, if it is not normal, call 10000 to report for repair normally into the second step.

2. Whether the wireless router interface is connected correctly. And make sure that the wireless router device is normal.

3. Check whether the computer has obtained the IP address and DNS normally.

It is recommended that you restart all your devices and test them again.

If there is anything you don't understand, you can log in to China Telecom's online business hall** or call 10000 to wish you a happy life.

Dear Telecom Users:

You need to connect the modem first, and then connect the wireless router.