Can Telecom Broadband Directly Connect to a Router Without Optical Modems?

No. Telecom broadband connection, installation of wireless routers.

There are three main reasons for not being able to access the Internet: 1. Broadband itself 2, user setting problem 3, router problem Network operators will give a fiber optic cat when installing fiber broadband, and the configuration inside is preset by the staff, and this optical modem.

It also has the function of automatic dialing, so the optical fiber modem of Telecom does not need to dial, but if we need to use dial-up to connect to broadband, how to set it up. Before the operation: 1. The super super of the fiber modem and the password (which will be discussed below).

2. Need to know the model of the cat (you can check it by logging in). 1. Preparation conditions 1: First of all, you need to know what the model of your fiber optic modem is, and you can directly log in to the back of the fiber modem and view it with the password. 2. After knowing the model of the cat, you need to obtain the super and password of the cat.

Because you only use the back of the optical modem and the password to log in, you can't get the set belief information at all.3. Acquisition of super password: After finding out the model of the optical modem, you can directly obtain it. 4. Log in to the modem through the above and password, and after the login is completed, you can find the broadband settings under the network.

Hello, no, fiber broadband needs to use the fiber modem, connect the home fiber to the fiber modem, and then use the network cable to connect the router and the fiber modem. The above information is for reference only, Anhui Telecom online business hall for you to serve.

Telecom optical modem. After cracking, it can be used as a wifi router.

If the optical modem of China Telecom has a wireless routing function, it can be used as a router, and if the optical modem does not have a wireless routing function, then it can be directly used as an external router.

As a relay transmission equipment for the local network, the optical modem is suitable for optical fiber terminal transmission equipment and leased line equipment of base stations. For multi-port optical transceivers, they are generally called "optical transceivers", and for single-port optical transceivers.

It is generally suitable for the user side and works similarly to the commonly used WAN.

The baseband modem used for private line (circuit) networking is called "optical modem" and "optical modem".

Extended Information: A router that connects to more than two separate networks. Being at the intersection of two or more networks allows packets (a form of organization of data) to be passed between them.

Routers and switches overlap in concept, but they are also different: a switch is a data relay device that operates at any network level (although it mostly refers to bridges, while routers are more focused on the network layer).

The difference between a router and a switch is that a router belongs to OSI Layer 3 products, and switches belong to OSI Layer 2 products. The second layer of the product function is to add the MAC addresses of each computer on the network.

Recorded in the MAC address table, when the computers in the local area network want to exchange and transmit data through the switch, the information in the MAC address table on the switch is queried, and the data packet is sent to the specified computer, instead of being sent by every computer in the network like the first-layer products (such as hubs).

OK. However, you need to tell the installer to turn on the router function. You can't set it up yourself. It is recommended to install a separate router. The bandwidth and wifi signal are better.

The optical modem cannot be used as wifi, and the optical modem is used to receive the broadband of telecommunications, so it cannot be used as a wifi to send signals.

The telecom optical modem can be used as a wifi router, and we can connect it.

They said that you are a little bad, and the girls who chase you are very sad, but I will never chase me, I want you to keep your charm charmed, and you will be far away and close to the end of your life.

Yes, the wireless signal of the optical modem is turned on, and the wireless coverage of the optical modem is relatively small, about 30 square meters. The effect of penetrating the wall is not good, if you are a large room, it is recommended that you install a router.

You can connect the cat port to the router port by performing the following steps:

1.First of all: pay attention to the connection port, do not connect the connection port incorrectly. Generally, the connection port will be marked. Note: The network cable that comes out of the Telecom modem interface is connected to the WLAN port of the wireless router.

<>2.The other ports of the wireless router are connected to the computer with a network cable, and the wireless router has four outgoing interfaces, one of which can be connected to the computer.

3.After the network cable is connected to the computer, look at the back of the router, you can find the login and setting method of the route, is:, the default password is:admin, as shown in the figure below:

4.Enter and enter the password on the web page on your computer to open the router's settings screen. As shown in the figure below:

5.After the login is completed, we directly choose to get it automatically, as shown in the following figure:

6.If the automatic acquisition option is unsuccessful, you can go to the advanced settings. Check the WLAN setting status and set it according to the following figure

Note: The default gateway of this telecom fiber modem is:

7.Since the telecom fiber modem does not need broadband and password, it can also be set up for static IP. As shown in the figure below:

Telecom broadband modems are not supported when used by routers.

The telecom modem itself does not support automatic dialing, so the routing function cannot be implemented. If you want to use a router, you need to connect to the router to transmit a network signal.

It doesn't make sense.

This is often the case when there is an error in the connection or settings;

The computer accesses the Internet through the router and directly connects to the modem to access the Internet, and the settings of the computer and the modem are different;

According to the manual of the optical modem, you should be able to access the Internet if you reset it.

Different optical modem settings are different, the following is the setting of Zhonglian Unicom products. The actual operation is subject to the manual

Install the modem, connect the cable, connect the power, start the modem, and wait for 5 minutes to start normally.

Connect the network cable of the computer to the first LAN port of the modem and the network port of the computer. And set the IP address of the computer as, mask, open the Internet Explorer, enter ** in the address bar, and press Enter to enter the login page.

Enter the username and password (the default web login username and password are admin and admin, respectively) on the login page, and you can enter the web configuration page of the modem.

Click "Advanced Configuration" --ONU Settings", configure the user's SN information in the SN position, and click "Apply" - Save Configuration. (For SN information, see the operator's installation ticket), and finally click "System Management" -- restart the modem.