What to do if the skateboard is dirty, how to clean the skateboard

Wash? Don't wash? Never let your plate come into contact with any liquids, including alcohol

If you really want to clean it, use a brush.

Use an eraser to clay and then brush off the eraser residue with a brush.

There are special sandpaper erasers abroad.

It doesn't seem to have been sold in the country.

Just use a plain hard eraser.

The bigger the block, the better.

Changing the sandpaper will do it Ordinary 20 30 sheets.

Actually, it's nothing to be dirty, and it's not so important to step on.

The even drip board has always been dirty and old When I first learned, in order to look like I had been playing for a long time, I deliberately made the skateboard dirty and old

Preparation of cleaning supplies:

1. Prepare a small wire brush first (an old toothbrush is fine, but the cleaning effect is not so good).

2. A clean rag.

3. A basin of water.

4. A piece of natural rubber.

5. (A hair dryer).

Steps: 1. Use a brush to stick some water, and brush the dirty area of the sandpaper repeatedly until the dirty things are brushed out.

2. Use a clean rag to wipe the area you just brushed.

3. Use a hair dryer to blow dry the sandpaper (the sandpaper that has not been dried is dark black, but the sandpaper after drying is light black with a little gray).

Fourth, use natural rubber to polish up and down on the sandpaper you just cleaned (the sandpaper washed each time is cleaner, and the friction and stickiness are stronger, but it is still not as good as the new one).

Please pay attention to the following points when using and storing the skateboard:

1. Do not sprinkle water on the board surface or place it in a wet place, the board surface, sand and shaft are very taboo water and moisture.

2. Try to practice in an open, flat and less crowded place when using, as violent impact will cause great damage to the board and people.

If the skateboard is only slightly dusty on the surface, you can wipe it directly with a rag, and the skateboard on the matte surface can be brushed a few times after being dipped in water, and then blotted dry with a rag, repeating several times to clean the dust on the surface.

If there are sticker marks on the surface of the skateboard, you can use gasoline and tar to easily remove the sticky marks from the tape, and then wash the surface with dish soap until there is no greasy feeling.

When cleaning the bracket, it is best to use a damp towel to wipe it, especially the metal screws need to use a dry paper towel to absorb water after wiping to avoid rust.

Bearings and wheels need to be serviced after cleaning, preferably with a layer of lubricating oil before attaching the wheels to them.

Novices are advised to choose a more stable one when buying a skateboard, at least the board surface can accommodate their feet, because the board surface of the skateboard is not stable when you first start skateboarding, so you should choose it in line with your actual situation.

When choosing a skateboard bracket, it is best to choose aluminum alloy, which is relatively strong and not easy to break.

It is best to choose a soft pulley, the soft pulley is quiet when gliding on the ground, and there is a cushioning effect when encountering stones.

1. Wheels. When selecting materials, it is necessary to consider that they are suitable for different site pavements, such as floor pavement, cement pavement, asphalt pavement, etc. No matter what road surface you are sliding on, the wheels must have good elasticity, wear resistance, and moderate hardness, and ensure that the wheels have enough friction coefficient for the road surface.

2. Cushion.

It mainly plays the role of cushioning and shock absorption. One is to play a role in shock absorption when the road surface is uneven; the second is to protect parts when there is a large amount of movement; The third pure type is leather pants, which play a role in keeping the body balanced.

3. a board surface. Generally, Canadian maple multi-layer board is used to compress into burning rock, and the compression process is divided into cold pressing and hot pressing, and cold pressing is to compress the wood chips directly without adding glue, which is more advanced and has better performance. The board surface has high impact toughness and good elasticity, which ensures that the pedal is not damaged when jumping on the skateboard at a certain height.

4. a bracket. The bracket, which we call "bridge" for short, is the skateboard accessory that bears the most torque, the most squeezing, and the most friction in the entire skateboard. Bridges are generally cast in alloys, and the craftsmanship and design vary from brand to brand.

Bridges are available in high, medium and low levels, and the length of the central axis of the bridge also matches the width of the deck.