How to adjust the surface of the skateboard to shake from side to side?

Skateboard shaking is normal, the key is to control the operation of the skateboard by training yourself to master balance skills.

When skateboarding, you should practice skating, focus on the pivot foot when skating, lean forward slightly, and drag the foot to support the ground rhythmically. If you want to stop, you can use methods such as directly lowering the board, pressing the board down, or turning and taxiing laterally. After walking and stopping, you can practice turning, use the force of your feet to make the skateboard tilt, and then cooperate with the rotation of your hands, waist and other parts of the body to control the size of the turning angle.

Once you've mastered these basic moves, you'll be able to play a variety of tricks.

Here are a few basic actions:

Practice skating first: Put your weight on the foot that is not moving, lean forward slightly when you slide the ground, and there is no trick to slipping more.

Turning: Usually which foot to use to support the ground to slide, put that foot on the tail of the board and apply pressure, while the other foot is slightly raised, and the board will be tilted at this time. Then use your hands and body (especially your waist) to do proper rotation (which is also a trick that can be grasped with regular practice).

The force of the body rotation is used to control the angle of the turn.

Stop: The most common way is to go down and pick up the board, or rub the ground with the root of the foot that usually slides the ground to slow down; You can also use the back foot to press down the uplift so that the board is 45 degrees and it will stop quickly, but I don't encourage you to use the brake method, and the end of the bottom of the board will wear out very much. If it's more difficult, jump up and catch the board, or use the foot you don't move to pedal the front of the board, lift the other foot a little bit, and use the turning method to make the board quickly slide sideways forward (the body should lean back), and then stop.

The board that the landlord bought is a children's board, right? How did it come up with the name "Skywalk"? Children's boards are generally relatively shaky, and the specific reasons are not clear, anyway, the wheels often rub the bottom of the board.

It is recommended that the landlord go to the skateboard store to buy.

If it is too shaky, you can tighten the big screw in the middle of the shaft, or unscrew the screw, put a kind of annular hard spacer (find it in the hardware store) and then screw the screw.

Also, skateboards can shake. You see**, after the master finishes the action, the board will also be tilted, different people have different requirements for the degree of swing of the board, but it is rarely said that the board will not be shaken, because the shaking of the board can buffer the impact after the jump, and the hard one will be easily injured; Small turns on the skateboard are also sometimes made by the shaking of the board.

If you really shake it, you should adjust it slowly, don't complain about the problem of the board at the beginning, and ask yourself to find a good balance and find the feeling of the board. Skateboarding really needs to be practiced, there is no other way.

** I've seen the connection.

It's a toy board, no off-road wheels, no regular skateboard.

In addition, the thing of this product** is completely different from the skateboard promotional photos in it.

It is recommended that you buy a starter board, a box that contains all the accessories for the skateboard, which can be assembled by the store owner or can be installed by himself.

300 500, look at the brand is still bad, there are more people who use the domestic boiling point novice board, about 300.

If you are new to it, learn more about skateboarding, find it on the Internet, study it, and take a look at skateboard stickers, skateboard tires can enhance your understanding of skateboarding as a sport and skateboard hardware.

Let's take it

Skywalk"? lz, you bought a toy board, right? . . The shaky deck is for you because the bridge is too loose, so you can tighten the main screws of the bridge a little with a tool.

Skateboarding left and right is a matter of center of gravity and foot position.

1.I don't know if the skateboard you're playing is a double rocker, a small fish board, or a longboard. Of course, no matter what kind of board it is, it has to do with the position of the feet and the center of gravity of the body.

2.In fact, the first thing you should know is what kind of foot you are used to skateboarding? Generally, I unconsciously find someone to push from behind, and whichever foot takes the first step is that foot.

3.Confirmation of foot position, generally the front foot step on the four screws of the slide board foot slightly inclined to the head of the board, the back foot horizontally placed at the back four screws, and after the slide to adjust the direction, the front foot can also be placed horizontally.

To sum up, as long as the foot position is good, that is, the foundation is laid, the center of gravity will naturally not sway from side to side. Another way is to keep your upper body as straight as possible, but bend your knees slightly to lower your center of gravity and improve stability.

Skateboard.

The skateboard is not flexible, and it can be changed by adjusting the tightness of the nut on the skateboard bridge.

Loosen the nut, the skateboard rotates left and right more flexibly, the turning is smoother, and it is suitable for skaters with better skateboard skills;

Tighten the nut, the left and right rotation of the skateboard is limited, it is not easy to turn, and it is more suitable for novices to practice skateboarding; It is also suitable for high-speed driving and rolling disadvantages, but the electric skateboard on the straight road.

This phenomenon is very common for several reasons:

1.The bridge is deformed, e.g. into an airplane bridge. It's just that the two ends of the bridge are inconsistent.

It is recommended to change the sleeve bridge] 2The main bridge nail is loose, so it's weird. 【Tighten it】Caused by uneven wear or cracking, including the small cushion in the shape of a cup.

As soon as this problem goes wrong, the safety hazards of skateboarding increase. [Change the set of PU pads, then adjust them, and tighten the main bridge nails] - more common.

4.The four wheels are not worn to the same degree. [Skateboarding should have been played for a while, pay attention to the protection of the wheels].

If you don't know how to ask, you must reply.

1. Take your time when sticking sand, don't let the air inside.

2. When there are bubbles, use a sharp knife to burst them.

3. Use a screwdriver to grind hard at both ends of the sandpaper to make the sand fit the board surface completely, which is for cutting.

4. Cut the knife and the plate at 45 degrees, with a sharp knife.

5. The order of installing bridge nails should be obliquely diagonal to avoid broken plates caused by uneven force application in the same straight line.

6. The board surface must not be damp or water, and the board surface that enters the water will not be brittle and will be scrapped soon. Remember, remember. Generally, the board surface is more difficult to damage, except for the board surface that has been exposed to water.

7. The bearing is fast without a cover but is afraid of ash, and the covered one is easy to explode, and the fish and bear paws are not available.

8. The bridgehead nut and screw should be on the same surface to avoid scribbling.

9. The front axle is loose, and the back foot is tight, so that it is easy to move.

10. The bridge PU should not be too tight, and it is easy to explode if it is too tight.

11. Domestic goods are generally not as good as foreign ones. Because domestic material science is not as good as foreign ones, this is not something that can catch up in a short period of time.

12. It's best to buy skateboard accessories, poor skateboarding will affect your technical progress, just as you are uncomfortable wearing poor shoes at the same time, it will have a bad impact on your feet, and poor skateboarding affects the speed of your technological progress.

13. When changing the board surface, the sandpaper and the board surface should be changed together. Don't tear the sand off and replace it with new sand. Not necessarily.

It's up to you to buy a T-tool specifically for removing or adjusting the skateboard.

Buy a T-tool or a wrench and hexagonal as well.

**Not adjusted**.

1) The anti-slip sand has a self-adhesive coating on the back, which can be automatically glued to the skateboard surface. Have your tools ready: a screwdriver and a razor. Remove the self-adhesive protective layer on the back.

2) Take the board surface out of the plastic package, lay it flat on the table or floor, and then start from one end, stick the sand on the board surface, press the bubbles while sticking, and pay attention to press all the bubbles out. Pay attention to the work surface to cover some old newspapers to protect the pattern on the bottom of the board.

3) Press firmly to flatten.

4) Use a screwdriver to scrape along the edge of the board surface for cutting. The purpose of this procedure is to remove the quartz sand from the cutting line to facilitate knife walking, while also allowing the sand to stick firmly to the edge of the plate. The scraped sand particles should be removed in time to avoid scratching the board surface.

5) Use the blade to cut off the excess along the edge of the board surface. Place the scraped sanded surface on a small stool and cut it with a white mark along the scraped edge of the blade. The blade should be tilted at an angle in the direction of the plate surface, about 45 degrees.

In this way, it can not only not hurt the surface of the board, but also cut it cleanly.

6) The cutting is finished and the sand has been pasted. During the operation, be careful not to let the falling sand particles scratch the board pattern.