Does the CBR1000 after 08 have the problem of burning engine oil?

Reasons for oil stains around the CBR1000 oil cap:

1. The sealing of the oil cap is not good, which may be caused by the aging of the sealing strip or man-made damage.

2. When adding engine oil, the engine oil is sprinkled around the oil cap, which is not cleaned, and if it is wiped clean, it must be cleaned at least three times with washing oil or gasoline.

For the oil cap with oil stains, if it is the oil stain formed by the aging of the sealing strip in the oil cap, this is abnormal, and replacing the sealing strip is conducive to preventing the oil in the oil tank from overflowing. If the oil stains are normal, the owner only needs to wipe it clean and check whether the oil cap is tight.

The owner must check the oil level of the socks brigade in the oil tank before driving, add or replace the oil in time, and tighten the oil cap in time after checking the oil to prevent the oil from overflowing the oil tank after boiling, resulting in less oil in the oil tank, which will also cause the smoothing effect of the auto parts to decline, and the heat generated can not be dissipated in time, so as to further heat and ablate the oil. It is recommended that car owners must pay attention to the maintenance of car oil and regularly check the oil level and quality.

Dear, if your Honda CB1300 burns engine oil, there may be the following reasons: 1Piston ring wear:

Wear of the piston rings can lead to a poor seal of the piston to the cylinder wall, which can cause the oil to enter the combustion chamber and burn out. 2.Valve guide wear:

Wear and tear on the valve guide can lead to poor valve stem sealing, which can also cause oil to enter the combustion chamber and burn off. 3.Water cooling system failure:

If the water cooling system is not working properly, the engine temperature will also be too high, which will cause the oil to burn off. 4.Cylinder wear:

Wear or damage to the engine block can also cause the oil to enter the combustion chamber and burn off. 5.Oil system failure:

There is a problem with the oil system, which causes oil and air to mix, which can also cause the oil to burn off. Solution: It is recommended that you go to a regular repair site for inspection and repair.

The engine is inspected by the maintenance personnel to identify the problem and replace the appropriate parts to prevent the oil from entering the combustion chamber and burning out. At the same time, the oil and filter should be changed regularly to ensure the normal operation of the engine.

The oil itself is consumed to a certain extent. If you consume too much, there is a problem of burning engine oil. Burning engine oil is caused by the following factors, as long as the following problems are solved, burning engine oil can be solved.

There are many factors that affect the burning of engine oil, such as: fuel quality, driving conditions, driving habits, maintenance habits, etc., the above reasons will aggravate the oil consumption and lead to the burning of engine oil, making the vehicle appear:

1. Carbon deposition occurs in the combustion chamber, which makes the gas ring of the piston ring stuck, and the sealing is poor.

2. Oil sludge is generated in the lubrication system, and the oil sludge blocks the oil return hole of the oil ring and weakens the oil scraping performance.

3. Wear occurs between the piston and the cylinder wall.

4. The valve seal is corroded and aging, and the sealing performance fails.

5. For vehicles with turbochargers, the sealing ring of the turbocharger is poorly sealed.

In addition, cars now have crankcase ventilation systems (exhaust valves), which can also exacerbate oil consumption if there is a problem. In the past, the problem of burning engine oil could only be solved by dismantling and repairing, but now there is a plan to solve the problem of burning engine oil without dismantling and repairing.

Burning engine oil, one is not anti-wear, and the other is assembly problems. The noise is loud because the oil is worn out and is not wear-resistant. The assembly is not good, the oil is burned, or the oil is not wear-resistant, worn, and the seal is not good.

These oils are average, and no one is better than the other. You need to use a good anti-wear oil to protect the car. Burning engine oil means that the engine oil is not anti-wear, and the wear particles are too large, resulting in poor sealing before burning engine oil.

Use super eutectic lubricating oil with good anti-wear performance to repair the slight burning of engine oil. And it's not expensive. It is not normal to burn engine oil, either there is a problem with the assembly, or the oil is not wear-resistant.

The oil used is not good and does not play an anti-wear role. Wear and carbon build-up are generated, resulting in louder noise. Remove carbon deposits, enhance power, eliminate exhaust gases, save fuel and reduce fuel consumption.

The use of ultra-American eutectic lubricating oil, close to zero wear, no oil burning.