If the local network cable is unplugged, the proe cannot be used

When the network is connected, start--run--cmd--type'ipconfig/all',Check your MAC address,Then unplug the network cable,Repeat the previous step,You will find that the MAC address is not the same,In general, your computer may have two network cards,Or only one,But there is a virtual one,When the network cable is unplugged,Your default network card is replaced,So when you start proe,When proe goes to read the license, you will find that the network card number in the license is different from the network card number of the current computer,So the license is illegal。 So proe is not available.

This situation has been encountered, the most stupid way, 1, if you use a virtual network card, then cancel, use the local network card. 2. Conversely, if you don't use a virtual network card, then install a virtual network card.

Then run the installation directory under . Bin can be repaired again, and the repair process only takes a few minutes.

Are you disabled for local connections. Then the problem you said would arise.

Because the MAC address is detected when proe is turned on.

Unplugging the network cable should have no problem.

This is because the system can't detect the physical address of your network card when you are not connected to the Internet, you go to the settings of the network connection, add everything that is not added in the IP protocol, and it's OK.

You are not a user of genuine proe.

You can use a virtual NIC instead of a physical NIC instead.

This problem may be a problem with the license, reset the license file (it is best to write down your physical address accurately, method: start - run -cmd - OK - enter ipconfig -all enter, you can see the physical address), and then open the directory file bin folder that proe is installed in, double-click, and go through it again, the time is very short!

Server Edition?

Installing pirate can effectively solve this problem.

The reason is that you plugged in a network cable when you installed it. The IP is automatically assigned, and if you don't have a network cable, you can't find the IP, if you often want to block the network cable, it's best to install a virtual network card. Then use the upstairs method to change the IP to the IP of the virtual network card, so that the network cable will not be closed with you in the future!!

I also had this issue, but it was resolved.

The network connection you have when you install proe must not be disabled during the uninstallation of proe after proe is installed, you can disconnect the network (unplug the network cable), but you can't disable it! Also, if your computer has several different network connection states, remember to disable all but the one you installed on Proe. I hope my method helps you.

Proe, are you sure you misspelled it? It's a **... If you use a network cable to access the Internet, if you unplug it, the communication will be interrupted, and the data packets will not be received, so you will naturally not be able to open.

If the Pro E is unplugged after booting up, it will not be turned on and an error will occur.

To install the proe service program.

Because PROE operation requires network card support, the specific principle is unknown.

You can install a virtual network card.

proe is supported by a network card, you install proe is to unplug the network cable, the license file is locked on a single machine (should be the third option), follow the prompts to complete.

1. Use the server version.

2. Self-installed piracy, without locking the license file on the stand-alone machine.

License lost,That's what I'm genuine for.,Break the network and cut off proe,There's no way around this.,If you're not genuine, it's recommended to change to a stand-alone version or reinstall it may be able to solve your problem.。

Your pore is using network resources, and it won't start if you unplug the network cable, so try setting it to stand-alone mode.

To connect to the network, the wireless network is also OK, and you must also connect to the network when using the software, but the network does not have to have traffic generation, that is, there is no need to have a fee, like a mobile phone in arrears, it is necessary to connect to the network service, but there is no real service, so that proe can identify your network card, each network card is unique to each computer, so as to generate a matching license.

Your NIC number will appear in the bottom left corner when installing, and use it to generate your license.

You don't need to add a license directly locally, but you need to enable a local connection, you don't need to connect to the Internet!!

You don't need to connect to the network, as long as the network card is installed with the network card driver, and if you don't have a network card, you can install a virtual one.

You uninstall the network card first, and then reinstall it.

If it's a desktop, as long as you have a network card, you'll be fine. If you have a laptop, you need to plug in a network cable, otherwise you can install a virtual network card.

You don't have to have a network card, you don't have to go online.

As long as your computer has a network card, if you don't have a network card, you can set a virtual network card in the segment.

It is installed as a stand-alone machine! No plugins required! Does the landlord have a new version?

No, it can be installed on a stand-alone machine

As long as your computer has a network card, there is no virtual network network, which card can be set up with a virtual network card.

Stand-alone installation must also let the computer know that you have a network card, so you have to set up a virtual network card or an ordinary network card, but now computers have integrated network cards, generally don't worry.