What to do if the heating pipe is clogged 100

1. Hair constitutes sewer blockage: After the sewer is used for a period of time, the hair that usually takes a bath will hang on the pipe wall and accumulate too much, which will constitute a blockage, and the hair will usually constitute a blockage of the toilet floor drain, washbasin blockage, bathtub blockage, and shower room blockage. Therefore, when using it, it is necessary to cover the floor drain cover and other protective equipment, and if there is hair, you can pick it up and throw it into the trash.

2. Oil scale blockage: Oil scale blocking the sewer usually appears in the kitchen, this blockage is usually the scaling of the inner wall of the pipeline, and the sewer is not dredged after the severe scaling of the pipeline. With a simple dredging method can not be handled, there will be just dredged and blocked, blocked, blocked, blocked, such is a vicious circle, to thoroughly deal with the only way is to use a high-pressure water truck to clean the inner wall of the pipeline, or replace the pipeline.

Relatively speaking, the use of high-pressure cleaning vehicles for dredging is more economical.

3. Pipeline collapse and pipeline dislocation: This kind of blockage usually occurs on the ground floor and outdoor sewers. There is no good way to deal with it: only find the location of the dislocation of the collapse, dig up and replace the pipe, and use the pipeline TV (pipeline detector) to identify.

The heating pipe is directly blocked, what should I do? Don't worry, the master will teach you a trick to fix it easily!

First drain the water for a long time to see if it can be flushed away, if not, bless the blocked pipe is not underground.

If it's definitely underground, and it's a good thing for you, it proves that it's not your responsibility to change the radiator.

There are two reasons why the radiator is clogged:1The long service life of the radiator leads to rust and corrosion inside the radiator, and impurities make the radiator clog. 2.The use of radiators will cause some limescale, which will then block the radiators.

Radiator unclogging method:

The inlet and outlet valves must be closed, the plug must be unscrewed, and the action should be careful.

Open the valve to flush the radiator, you can see the impurities inside flow out with the water flow until the water is clean, then close the valve, then change to another valve, repeat the above actions, and then close the valve and tighten the plug.

In this process, there will be more or less some air entering the radiator, so it is necessary to vent the radiator after dredging.

Unscrew the running air until the gas is exhausted and the water is out, which proves that the air has been discharged, and then tighten the running air.

In this way, the heating can be restored to its previous smooth state.

In a few steps:

1. Touch the radiator farthest from the boiler, the upper part of the radiator is cold, and the lower part is hot, indicating the lack of water. Hydrate as directed.

2. If it is not hot up and down, it is blocked by debris or needs to be deflated. It is best to find a professional to clean up, about 200 yuan;

3. The above-mentioned simple treatment still has no effect, or the service life is more than 10 years, and professional treatment is required, including the above-mentioned treatment and boiler cleaning. Or, it's closer to changing the boiler.

2, the main thing is not to be fooled, to prevent simple processing of overcharges.

It's good to find a professional to unclog the pipes.

The heating pipe is clogged, we can use the home's cleaning method first. Generally speaking, one end of the pipeline to the other end, respectively, is the structure of the inlet and outlet, so we can add some internal dirt removal solution from the end of the inlet water, here if there are friends with economic conditions, it is best to use special personnel to provide door-to-door service, they not only have a professional solution, but also have a professional equipment to clean up the blockage, which can help us to meet the cleaning requirements with minimal damage to the pipeline. In addition, if you plan to operate it yourself, you should at least buy a professional solution to remove dirt, because the dirt inside is basically limescale, or blockage caused by rust, so we can buy cleaning agents in these two directions.

In addition, if we want to use some more household cleaning methods, we can also prepare some baking soda cola, or white vinegar, these items will react with calcified ingredients, which can achieve a relatively good effect of glass calcifications.

1. First of all, you need to close all the valves of the water collector.

2. Use a wrench to remove the nut on the right side of the drain pipe of the water collector.

3. Put on the basin to prepare to receive water, and then blindly open the main grinding valve of the water inlet pipe, and then open the water inlet valve of the water distribution pipe and the outlet valve of the corresponding water distribution pipe.

4. Discharge water to each water distribution pipe in turn, until the outlet of each water distribution pipe of the water collector has heat to end the water discharge, and the nut can be screwed on after the most He Ling.

Summary. Pro-<>

Hello, the pipe blockage under the heating The solution is as follows: 1. When the pipe is blocked under the heating at home, it is caused by the air, we need to open the exhaust valve and let go of the air in the heating. 2. The pipe blockage under the heating is because the gas pipeline is blocked by the scale that has not been cleaned for a long time, you can ask professional dredging personnel to come to dredge the plumbing, and the heating pipe at home is accidentally welded to death, you can ask the plumbing construction worker to replace the heating pipe. 3. The room is relatively dry, you can use a humidifier with floor heating, and you must open the window properly for ventilation, otherwise the radiator at home will be blocked.

And the water of the installed radiator can not be discharged at will, if it is discharged at will, it will not only affect the indoor heating effect, but also damage the radiator. Pro-<>

What to do if the pipes are clogged under the heating <>.

Clogged plumbing pipes under the heating.

A small piece of toilet paper leaks into the water inlet.

Hello dear <> The solution is as follows: 1. When the heating pipe at home is clogged, it is caused by the air, and we need to open the exhaust valve and release the air in the heating. 2. The heating section knows that the pipe is blocked because the scale has not been cleaned for a long time, and the gas pipeline is blocked, you can ask professional dredging personnel to come to dredge the plumbing, and the heating pipe at home is accidentally welded to death, you can ask the plumbing construction worker to replace the heating pipe. 3. The room is relatively dry, you can use a humidifier with floor heating, and you must open the window properly for ventilation, otherwise the radiator at home will be blocked.

And the water of the installed radiator can not be discharged at will, if it is discharged at will, it will not only affect the indoor heating effect, but also damage the radiator. Pro-<>

<> a piece of toilet paper plugged the sewer pipe.

Hello <> the water connection of the pipe under the heating leaks into a small piece of toilet paper, and the smile ridge is high, you can pour hot water into the water pipe to speed up the decay rate of the raw paper.

Good. There are no drugs that corrode toilet paper.

Hello <> 84 disinfectant can corrode toilet paper,

Nowadays, many people will install radiators at home, so that in the cold winter, you can turn on the radiators at home for heating, but after a period of use, there may be a situation where the heating pipes are blocked, so what should I do if the heating pipes are blocked? How to prevent scaling and corrosion of heating pipes? Let's take a look!

1. What should I do if the heating pipe is blocked?

In the case of blockage of the heating pipe caused by scale, you can ask a professional to clean the radiator pipe to remove the scale and stains in the heating pipe, if it is blocked due to the corrosion of the heating pipe, you need to remove the corroded heating pipe and replace it with a new heating pipe, the process is more complicated, so you must not disassemble the heating pipe without authorization.

2. How to prevent scaling and corrosion of heating pipes.

1. To prevent the scaling of the radiator, you can use the radiator antiscalant, because the composition of the antiscalant is organic matter and alkaline substance, and the antiscalant is poured into the heating pipeline, which can convert the calcium and magnesium ions in the water into water slag, so as to avoid the scaling of the heating pipeline, and at the same time promote the discharge of water slag.

2. Increasing the number of groups and pieces of radiators can also prevent scaling of heating pipes, because through this method, the hot water temperature of heating pipes can be reduced, thereby reducing the production of magnesium carbonate and calcium carbonate and other substances, and preventing the phenomenon of scaling in heating pipes.

3. During the non-heating period, the heating pipe needs to be filled with water, which can not only isolate the space, but also avoid the corrosion of the heating pipe.

Summary: What to do if the heating pipe is blocked, the relevant content is introduced here, the heating pipe blockage is a common problem in the use of radiators, so we must know how to prevent the heating pipe blockage when using, so as not to affect the normal use of heating equipment. If you want to know more about decoration, you can pay attention to the relevant information of Qeeka Home.

1. First of all, close all the valves of the water collector.

2. Use a wrench to remove the nut on the right side of the drain pipe of the water collector.

3. Put the basin ready to receive water, then open the main valve of the water inlet pipe, and then open the water inlet valve of a water distribution pipe and the outlet valve of the corresponding water distribution pipe.

4. Drain water to each water distribution pipe in turn, until the outlet of each water distribution pipe of the water collector has heat to end the water discharge, and finally screw the nut on.

The heating pipe blockage is unblocked and unclogged as follows:

At first, turn off each valve of the water collector and unscrew the nut on the side of the water collector drain pipe with a tool; Take the basin to receive water, then open the main valve of the water inlet pipe, and then open the water outlet valve of the water distribution pipe and the corresponding water distribution pipe; Discharge water to all water distribution pipes in order, and complete the water discharge when all the water distribution pipe outlets of the water collector are hot; Finally, tighten the nut tightly.

Precautions for the installation of heating pipes

1. When the pipe penetrates the floor and wall, it is necessary to install iron sheets or steel bars to cover the pipe. In this process, the casing needs to meet the following conditions: the casing installed in the wall needs to be flush with the wall finish on both sides, so as to ensure that the pipe is not disturbed when it is expanded or contracted.

In addition, if there is water accumulation on the ground, it will not flow to the lower layer; The bottom of the casing installed in the floor slab should be on the same plane as the bottom of the floor slab, and the top should be 15 to 20 cm above the ground.

2. When installing radiators in the room, the original heating pipes should not be changed as much as possible, if the heating pipes need to be changed, it is important to pay attention to the inner diameter of the pipes should not be smaller than the original, so as to avoid the problem that the radiators are not hot and the heating effect is not obvious when using.

3. The device of the radiator branch pipe should be installed after the radiator and riser are installed, or the device should be installed together with the riser. When the radiator branch pipe passes through the wall, in addition to adding a casing, it is also necessary to pay attention to the fact that the branch pipe should not have a joint in the wall.

When installing a valve on the branch pipe, the radiator side should be connected with the detachable type unloading, and when the radiator branch pipe is installed, the steel pipe must be adjusted appropriately before meeting, so as to prevent the branch and riser from tilting.

The weather in northern families is cold, and the homes will be heated in the form of a grind. However, due to poor water quality or more impurities in the water, the heating pipe will be blocked, resulting in the heating pipe not being hot. So how to unblock a blocked heating pipe?

What to do if the pipe is leaking? Let's learn about it right away.

1. How to dredge the blockage of heating pipes.

There are two causes of clogged heating pipes, which are gas blockage and impurity blockage. The reason for the air blockage is that part of the air runs into the heating pipe, just use a screwdriver to loosen the exhaust valve on the heat sink, and the air will automatically run out. If the heating pipe has not been cleaned for a long time, there are too many impurities such as scale in the pipe, which will cause the heating to be not hot.

2. How to deal with the leakage of heating pipes.

1. Do not open and close the heating pipe valve arbitrarily.

After the end of the heating period, there will be a certain amount of air and impurities in the pipeline, and the heating unit will test the water for the user's home during the heating shutdown, reach the appropriate position of the valve, open the air valve, and squeeze out the air in the radiator. Once commissioned, the user should not open and close the valve at will.

2. Don't change the pipeline within a week.

After the heating is stopped, the user should not drain the water in the radiator and pipes without permission. Since this is softened water, it has undergone anti-corrosion treatment to isolate the corrosion of the pipeline by air and prolong the service life. In addition, within a week after the heating is stopped, do not disassemble and install the heating line without permission, because there will generally be residual water left in the pipeline, in case of water leakage, not only to yourself but also to bring unnecessary trouble to neighbors.

Conclusion: The causes and treatment methods of heating pipe blockage are introduced here, and it is recommended that friends pay attention to the process of using heating: generally ordinary heating should be cleaned once for more than 3 years, so that the radiator can "prolong life".