What s going on with the washing machine?

It should be a problem with the door switch, the dehydration display e2, directly short the door switch, if there is no problem, it is the door switch is broken, if it still doesn't work, it may be a problem with the line or computer board.

1.The laundry is in an unbalanced state when washing. Elimination method: You can put a small amount of clothes before washing clothes, and don't stuff too much at once, so as not to cause imbalance during washing. And the effect of dehydration is not good.

2.The safety switch on the top cover of the washing machine is damaged. Try not to open the top cover during the dehydration process to avoid damage to the top linkage switch.

3.The washing machine drain system is clogged. Elimination method: Remove the drain filter and clean, rinse the drain with water and remove the debris in the drain valve.

4.The water level switch cannot be reset. Solution: Contact the after-sales point.

5.Due to a faulty motor, the washing machine cannot be dehydrated. Exclusion Method:

You can try opening the back cover of the washing machine and moving the pulley by hand if there is no jamming. If the motor does not rotate when the power is turned on, it means that the motor is short-circuited or damaged between turns, or the capacitor is not connected to the motor circuit. At this time, the power supply should be cut off, and the motor belt should be removed and restarted.

If the motor still does not rotate or the speed is low, it is a motor failure and the motor should be repaired or replaced.

6.The washing machine cannot be dehydrated due to the damage of the solenoid valve: The washing and dewatering of the automatic washing machine is completed by converting the gear at the bottom of the solenoid valve, and the damage of the solenoid valve will also make the dehydration unable to operate normally!

7.The motor plug is loose and the washing machine cannot be dehydrated: Troubleshooting: It should be plugged back in and tied with a strapping wire to prevent it from falling off again.

8.The computer control board is faulty and the washing machine cannot be dehydrated: troubleshooting: The brain control board can only be replaced, because the control board is covered with glue in order to be waterproof, and it is quite inconvenient to repair!

9.The action of the electric motor thermal protector causes the washing machine to not be dehydrated. Exclusion method: At this time, it can be used as long as the thermal protector is reset.

10.Some models are equipped with a non-dehydration button, and the washing machine is not dehydrated. Troubleshooting should first check if the non-dehydration key is pressed. If this button is pressed, the washing machine has an anti-wrinkle function and does not dehydrate the laundry. As long as the non-dehydration button is raised, the washing machine can be dehydrated.

1. Stop the water inflow before the water level is reached. This failure is likely to be caused by the poor performance of the water pressure switch, because the air pressure is not enough to promote the contact to close in advance, which can be adjusted by controlling the amount of spring pre-compression, only need to screw in the adjusting screw, if the water level control spring loses elasticity, it needs to be replaced, and the wear of the groove on the water pressure switch cam will also lead to the cessation of water ingress, which also needs to be replaced.

2. In the washing state, the motor rotates normally but the wave wheel does not rotate. The mechanical transmission part between the motor and the wave wheel is prone to this kind of failure, generally because of the fastening screw Wang Socks loose, slippery, broken and other reasons, as long as tightened, replace the screw, serious to the wave wheel square hole rounded, you need to replace the wave wheel, in addition to the good song may be because of the V-belt slippage, falling off, or clutch deceleration mechanism parts wear and tear, all need to be replaced.

3. The dehydration bucket rotates at the same time in the washing state. This kind of fault is generally divided into clockwise direction and counterclockwise direction at the same time, mainly because of the brake belt loose, serious wear and other reasons, need to reinstall the brake belt, or rotate the adjustment screw to deal with.

4. Drainage timeout. The normal drainage time of the washing machine will not exceed 4 minutes, if it exceeds this time and still does not reach the empty water level, it may be because the drain pipe is not put down, foreign objects block the drain port or the drain valve is not opened to cause sleepiness, or it may be caused by the bending of the drain pipe, this fault is more common and is basically easy to solve.

There are many types of faults, and it is necessary to explain what kind of fault it is so that it can be dealt with.

Turn on the power supply, the indicator light is not on, and the reason for the failure of the whole machine is that the whole machine does not respond, and the power outage. The fuse blew, the air switch tripped, and the power outlet was damaged. Check each of the above items one by one, and if everything is normal, then check the washing machine.

The power cord is soldered or the wire is broken, resulting in the power cord being blocked. Use a multimeter to measure and detect, and replace the three-pin plug or power trace after determining the open circuit.

The DC power supply circuit is faulty. Disassemble the cover plate of the washing machine, remove the computer board, detect the power transformer of the DC power supply, rectify the hungry flow diode, filter capacitor, three-stage voltage regulator, etc., if any damaged components are found, they can be replaced with new parts of the same specification and model.

If the motor, water inlet valve, and drain valve are not working, it means that several bidirectional thyristors that control the load parts are not working.

If it is a semi-automatic washing machine, there may be a problem with the timer power connection; If it's a fully self-washing machine, there may be a problem with the control circuit board. It is also possible that the washing machine motor overheats due to the external environment and excessive washing of clothes, and the motor thermal protector automatically disconnects the circuit to stop the washing machine; The location of the washing machine is not well ventilated, or the ventilation hole at the bottom of the washing machine is blocked, and the heat dissipation is poor; Check if the voltage is normal, when the voltage is too high or too low, the washing machine may also have the above situation. The solution to the washing machine in a state of washing all the time:

1. Turn on the drain pump first and clean up the dirt inside. 2. Check whether the drain pipe is blocked, it is recommended to clean it up. 3. Check whether the drain pump plug-in wire is loose, whether the drain pump has been damaged, and whether there is a voltage channel drain pump.

4. If there is no voltage to the drainage pump, focus on checking the program controller or computer board. 5. Check whether the laundry washed in the washing machine is excessive, if it is excessive, please take out part of the laundry before washing. 6. Check whether the belt is loose and adjust the belt.

7. Check whether the motor is in poor contact, repair or replace. 8. The washing machine wheel is stuck, disassemble and clean up, and pay attention to power off for cleaning. 9. If the timing switch of the washing machine is damaged, it shall be repaired or replaced.

The common faults of washing machines are as follows:

The power switch cannot cut off the power of the washing machine, please ask the company's maintenance personnel to repair it.

Abnormal water pressure makes the water inflow too small, so try to increase the water inflow.

If there is no drain within the specified time, the drain is not lowered or the drain system is blocked, lower the drain or clear the blockage.

After the appointment started, the door lid was not closed.

Set the washed laundry aside and place it evenly around the bucket.

The undervoltage protection voltage rises and starts, and everything returns to normal.

The appointment time is not enough to increase the appointment time.