Is there a difference between Fanuc 0i mate MD and Oi MD?

The differences between Fanuc 0i-mate-MD and OI-MD are: different processing speeds, different number of reads, and different flexibility.

First, the processing speed is different.

1. Fanuc 0i-mate-md: For denser and shorter line segments, Fanuc 0i-mate-md processing speed is slower than Fanuc OI-md.

2. Fanuc OI-MD: For denser and shorter line segments, Fanuc OI-MD is faster than Fanuc 0i-mate-MD processing speed.

Second, the number of pre-read paragraphs is different.

1. Fanuc 0i-mate-md: The number of preread segments of AICC in Fanuc 0i-mate-md is longer, which is 40 segments.

2. Fanuc OI-MD: The number of pre-read segments of AICC in Fanuc OI-MD is shorter, which is 16 segments.

Third, the flexibility is different.

1. Fanuc 0i-mate-md: Fanuc 0i-mate-md has better flexibility, and cannot frequently perform acceleration, deceleration, and cornering actions.

2. Fanuc OI-MD: Fanuc OI-MD has better flexibility and can frequently perform acceleration, deceleration and cornering actions.

The OI MD is available in two configurations: A and B.

Configuration A: Motor. High precision and low horsepower. It is suitable for precision molds, and the multi-surface molding effect is good.

Configuration B: Motor. Slightly worse accuracy High horsepower. It is about 20,000 cheaper than configuration A. Suitable for mold parts processing slightly worse than a but not obvious.

Mate: It is the low-end product of the FAUNC version of the system, 0I-MATE-MD is the reduced version of the OI-MD using a motor, and the computing hardware of the system is also relatively poor, which is only suitable for simple parts processing within 3 axes.

In fact, the most important thing to ensure the accuracy of the machine tool is the hardware quality of the machine tool itself.

There are only a few points to help you understand it simply:

1.The two generations of cost-effective series of products, pure substitution relationship, the market direction is exactly the same - economic machining center and boring machine, in most cases there is no competition, just like WinXP replaced Win2000;

2.0i mate-mc and 0i-mc and fs18i are products of the same era, from about 2003-2008,; 0i-mate MD is the same era as 0i-MD and FS31i, and has the functions of nano-interpolation and other functions that can only be found in the FANUC system in that era.

Other new features in mate-md:

a.4 feed axes can be controlled optionally, and 5 can be controlled next year;

b.Maximum feed speed: 240m min).

c.Macro actuator, fanucpicture - interface development function;

d.Chinese alarm display function;

To sum up: there must be improvements, but you may not use all of these differences. If you're introducing it to a user, then it's enough to talk about these points; If you choose a system, you basically can't buy the former; If you choose a machine tool, you don't need to pay too much attention, but be careful of the warranty date of the MC, and because of the nano interpolation, the smoothness of the MD processing may be a little better.

There are only a few points to help you understand it simply:

1.The two generations of cost-effective series products, pure substitution relationship, the market direction is exactly the same - economic machining center and.

Boring machine. In most cases, there is no competition, just like WinXP replaced Win2000;

0i mate-mc and 0i-mc and fs18i are products of the same era, from about 2003-2008,; 0i-mate

MD is the same era as 0i-md and FS31i, and has this era.

FANUC system.

Only then did the nano.

Imputation. and other functions;

Other new features:

a.4 feed axes can be controlled optionally, and 5 can be controlled next year;

b.Maximum feed speed: 240m min).

c.Macro. Actuators.

FanucPicture - interface development function;

d.Chinese alarm display function;

To sum up: there must be improvements, but you may not use all of these differences. If you're introducing it to a user, then it's enough to talk about these points; If you choose a system, you basically can't buy the former; If you choose a machine tool, you don't need it.

I care too much. However, beware of the warranty date of the MC, and because of the nano interpolation, the smoothness of the MD processing may be a little better.

There are only a few points to help you understand it simply:

1.The two generations of cost-effective series of products, pure substitution relationship, the market direction is exactly the same - economic machining center and boring machine, in most cases there is no competition, just like WinXP replaced Win2000;

0i mate-mc and 0i-mc and fs18i are products of the same era, from about 2003-2008,; 0i-mate

MD is the same era as 0i-MD and FS31i, and has the functions of nano-interpolation and other functions that can only be found in the FANUC system in that era;

Other new features:

a.4 feed axes can be controlled optionally, and 5 can be controlled next year;

b.Maximum feed speed: 240m min).

c.Macro actuator, fanucpicture - interface development function;

d.Chinese alarm display function;

To sum up: there must be improvements, but you may not use all of these differences. If you're introducing it to a user, then it's enough to talk about these points; If you choose a system, you basically can't buy the former; If you choose a machine tool, you don't need to pay too much attention, but be careful of the warranty date of the MC, and because of the nano interpolation, the smoothness of the MD processing may be a little better.

There are only a few points to help you understand it simply:

1.The two generations of cost-effective series of products, pure substitution relationship, the market direction is exactly the same - economic machining center and boring machine, in most cases there is no competition, just like WinXP replaced Win2000;

2.0i mate-mc and 0i-mc and fs18i are products of the same era, from about 2003-2008,; 0i-mate MD is the same era as 0i-MD and FS31i, and has the functions of nano-interpolation and other functions that can only be found in the FANUC system in that era.

Other new features in mate-md:

a.4 feed axes can be controlled optionally, and 5 can be controlled next year;

b.Maximum feed speed: 240m min).

c.Macro actuator, fanucpicture - interface development function;

d.Chinese alarm display function;

To sum up: there must be improvements, but you may not use all of these differences. If you're introducing it to a user, then it's enough to talk about these points; If you choose a system, you basically can't buy the former; If you choose a machine tool, you don't need to pay too much attention, but be careful of the warranty date of the MC, and because of the nano interpolation, the smoothness of the MD processing may be a little better.