Apple s iPhone gets into the water, can it still be repaired if it can t be turned on?

1. If the mobile phone gets into the water, it is recommended not to turn it on immediately, and use a hair dryer to blow the water inlet down first.

2. Then put it in a shutdown state for about two days, and then try to turn it on.

3. If it can't be turned on, it is recommended to send it to the Apple after-sales center to help you detect what the fault is.

1. Do not shake the fuselage when it is turned on.

Once your iPhone gets water, it should be turned off immediately. Keeping the computer on in the case of water ingress will form eddy currents, cause short circuits, and the motherboard will burn out. So never turn it on.

2. The first thing to do after shutting down.

After shutting down, first wipe off the water on your phone's case with a towel. Then quickly unplug the SIM card and keep it somewhere else. Next, use a paper towel to suck up the water from the headphones, dock and SIM card slots.

3. Use a damp towel to wipe off stains that are difficult to remove.

There are many situations in which the iPhone 6 is flooded or flooded, for example, in addition to fresh water, there are muddy water, sea water, juice, etc. If fresh water enters the phone, you can wipe off the water with a towel after turning it off. If water enters the interface of the mobile phone, it can be removed with a paper towel or cotton swab.

Go to Apple after-sales and ask.

If the iPhone gets into the water, it should be powered off immediately.

There are also the following methods:

1. Don't try to turn it on, try whether the phone can be used. After powering on, it will directly cause a short circuit on the mobile phone motherboard, and there is a possibility of burning the mobile phone motherboard.

2. Place the phone screen facing down. After the phone enters the water, put the phone screen down with the back cover of the phone facing up, and then lay it flat. This minimizes the possibility of water entering the motherboard of the phone.

iphone：

As of September 2022, AppleInc) has released 37 mobile phone products; The mute button of the iPhone is on the left side of the front of the device; Models before iPhone 5 use a 30pin (i.e. 30 pin) interface, and products after iPhone 5 (included) use a Lightning interface. Models before iPhoneX are equipped with the home button; iPhoneX (included) after (except iPhonese.

The second and third generations) models have canceled the physical home button. <>

How to deal with the water after the iPhone is ingressive.

1.Turn off the phone as soon as possible, cut off the power, and do not try to turn it on again to avoid causing a short circuit in the motherboard.

2.Remove the SIM card and use a tissue or cloth to remove water from the outside and crevices of the phone.

3.If there is light water ingress, you can wrap the phone with a paper towel, put it in a bag and put it in a small bag of desiccant.

4.The mobile phone cannot be turned on after entering the water, most of the chips such as the motherboard and CPU are short-circuited and burned, and it is recommended to send it to the after-sales service center for repair immediately.

Don't try the following wrong methods after your phone gets into water.

1.Don't shake your phone too hard. Because under the constant shaking, the liquid will swim inside the machine, and the moisture may enter deeper and burn the internal chip of the machine.

2.Don't use the hot air of a hair dryer to dry your phone for a long time. iPhones are now all metal bodies, and metal conducts heat easily, which will blow off the solder joints of the motherboard inside the machine, causing the motherboard to malfunction.

3.Do not attempt to charge a phone that has been flooded. An iPhone that gets into the water may have water stains inside, which can burn out the motherboard when it is powered on and cause a more serious failure.

4.Do not leave your phone in water for a long time. In the case that it cannot be used normally after two or three days after general treatment, it should be sent for repair immediately, and long-term placement will cause the motherboard to be corroded, or even unable to be repaired.

1. Easy to get liquid?

There are the most openings on the iPhone body, and the easiest thing to get into the liquid is the bottom, which has the "headphone hole", "tail jack", "phone MIC", "speaker hole", and then the card slot. The easiest thing to get into the front is the earpiece.

2. How to deal with it urgently after liquid ingress?

Water reacts electrochemically with many metals, especially when energized and the water contains complex ions, which can lead to more complex corrosion, much like this.

Nowadays, the mobile phone motherboard is highly integrated, the circuit is complex, and the mobile phone is likely to be open or short-circuited after it cannot be turned on by water, which may cause permanent damage in other places, and it can be rescued if handled properly.

1. Power off immediately.

If the battery can be removed, remove the battery immediately; If the battery is not removable and the mobile phone is still working, turn off immediately, and you can disassemble and disassemble the battery if you have the ability to do it; If the mobile phone can't be turned on when the water is in the water, look directly at the next step.

2. Correct placement.

After disconnecting the power supply, according to the different positions of the liquid intake, throw it out vigorously in the direction of the opening, and then follow the correct method, find a ventilated and dry place, and leave it for a period of time to dry, the purpose is to keep the liquid entering the fuselage from flowing to the motherboard as much as possible. This can only damage the screen, handset, or tail plug, minimizing the damage.

If the entire fuselage is soaked in water, it doesn't matter what self-help, the longer the motherboard corrosion, the more serious the corrosion of the motherboard. Find a reliable third-party repair shop as soon as possible to disassemble and clean up.

If it is part of the liquid ingress, according to the above practice to preserve the mobile phone, the functions are normal, at this time do not have a fluke mentality, should immediately find a reliable repair service provider to disassemble the machine for a comprehensive cleaning, with washing water and pure alcohol to treat the inside of the mobile phone is a complete strategy, the cost is only a few dozen yuan.

Twist the screws, disassemble the screen, disconnect the battery board, dry it with a hair dryer, and if it looks good, take it to after-sales maintenance.

iphone6 water does not turn on, pick up a leak, fortune small capacitor is here again!

Reasons why the Apple phone can't turn on:

1. There is no electricity. If you use up all the battery power, the charge needs to be charged to 5% before it can be turned on normally. So in this case, please let the phone charge for a while before trying to turn it on.

2. Software malfunction. If you are sure that the current battery of your phone is sufficient, but it cannot be turned on normally, there may be a problem with the software system of your phone. At this time, we can try to press the home button + power button on the home screen of the mobile phone at the same time until the screen is lit up and there is a display.

3. System crash. If none of the above solutions work, and you see an iTunes connection screen on your iPhone's screen, it means that your phone has entered recovery mode at this time. When this happens, the only way to do this is to restore the system for your phone.

Connect your phone with the computer with a data cable, press and hold the home button and the power button at the same time for 10 seconds, then release the power button and continue to press and hold the home button for 5 seconds, if you see the connection to iTunes, it is a failure, and you have to start again. If the screen doesn't light up after these 2 steps, you will enter DFU recovery mode, and then you can use iTunes to restore your iPhone, or use a third-party flashing software to reflash your iPhone.

In response to your question: let's talk about how to deal with it first, the first water ingress must be turned off first to prevent burning the motherboard;

The second is to dry the mobile phone from beginning to end, use a cotton swab to get the gap in and absorb it, and the third is to put a paper towel or bag in the rice jar and seal it for 2 days to let the moisture absorb dry.

The above three steps are what Xiaobai should do, after all, Apple is a whole machine and can't remove the battery by itself, so it can only do this.

But what happens after 2 days?

If it is not serious, it can be used normally, but if it is serious, it will have a blurred screen, a black screen, and various small problems.

In fact, regardless of whether it is used normally or not, there is still water inside our mobile phones, and this water will definitely not be absorbed by rice so easily. Even if it is displayed normally now, the mobile phone is working with illness, and it may crash or even be scrapped at any time.

Because the water enters the circuit of the motherboard, if you don't disassemble the machine and do an internal cleaning with plate washing water and ultra-green wave, it will slowly oxidize and rust, and wait until a certain time, so many lines only need a short circuit, the entire motherboard will be wasted, and it is irreparable. Because by that time, all the lines would be almost rusty.

Therefore, we must take the water inlet machine to disassemble and clean it as soon as possible, and the other thing is that the water inlet machine apple is not guaranteed, which is artificial. And there are some labels in the Apple phone, as long as the water enters, those labels will turn red. Apple will not have a warranty after sale.

It can only be repaired by a mechanic master. Because it is very annoying to do the whole machine cleaning process, the internal fine parts need to be dismantled by professional equipment to clean and dry, and many places are troublesome, only a few large pieces are cleaned up, and the fine cleaning can not be done. And basically there are no ultrasonic instruments to remove water in those places.

There are so many tiny parts, just by a hair dryer to blow, it is useless. So why there will be problems after a while after many water inlet machines have been cleaned, this is also the reason.

If the screen goes black, most of them are broken by the power supply of the motherboard or the baseband of the CPU hard disk. This can only be repaired by experienced masters. Most small shops can give you a replacement part, after all, it is only a disassembly and assembly, which is relatively easy, but to repair at the chip level, it is a headache, and most of the answers are that it cannot be repaired or returned to the factory.

Their so-called factories are factory stores with equipment and machines on our side.

Repaired **, I'll talk about it too. It depends on the severity, cleaning up ** is not expensive, about 100 yuan is OK, the key is that if you design to repair large pieces, iphone6 is basically hundreds to thousands.

Step 1: Get your phone back. du

If your phone falls into the bucket or the bottom of the bath, don't be stunned and get it out.

Step 2: Remove the capacitor cell. Don't press any keys, and you don't need to turn it off, just open the back case of the phone and remove the battery. What if it's a phone like an iPhone that can't pry open the back cover to remove the battery? Then be careful to turn off the phone as soon as possible and cut off the power to prevent the phone from short-circuiting.

Step 3: Remove moisture. Remember, don't use a hair dryer to dry or bake on the stove, as the heat from the outside can damage the delicate electronics inside the phone. The correct way to do this is to wipe it quickly with a clean towel to make sure that water does not run into the charging port, headphone jack, etc.

If you find that the water has flowed down the connector or through the gap into the phone, carefully blow the water out with compressed air, and never blow deeper and deeper.

Step 4: Drying. Many people leave their phones in dry rice bags for 24 to 36 hours, or even longer. To be on the safe side, make sure to wrap your phone loosely in a paper towel before putting it in the rice.

The probability of repairing it for a long time is not very large, and it can still be repaired when it is taken out of the water as soon as it is dropped, but it will not work for too long, and the electronic components inside will burn out and oxidize.

If you fix it yourself, you can only wipe it clean with wet paper and remove it carefully, there is no better way. Of course, the specialty shop can, but I don't know if it's ruthless to slaughter, relying on luck.

The apple can't turn on when it gets into the water, and there may be the following reasons:

1. Apple has a water ingress protection mechanism, and it is recommended not to turn on the machine and put it in the rice bag to continue to absorb water, and wait for it to dry completely before turning it on.

2. The motherboard has burned out, too much water may cause the motherboard to burn out, for this case, it is recommended to send it to the mobile phone store to replace the motherboard.

Turn off the machine immediately after entering the water, then wipe it with a dry paper towel, and then use a hair dryer to dry the water, but don't rush to turn it on. It should be no problem to turn on the computer after a day.

It can be repaired, first wipe it clean with a towel, then blow it with a hair dryer for a few hours, and then see if it can be turned on, if not, it can be repaired at the mobile phone store.

It is not easy to repair the mobile phone if it is flooded, because the circuit board inside the mobile phone has accumulated water and has burned out.

When entering the water, you must not turn on the machine immediately, you must blow it with a hair dryer first, and if possible, you can put the mobile phone in a fresh-keeping bag and then put it in a rice jar, and try it overnight.

If the mobile phone gets into the water, it is generally blown by blowing first, and then the mobile phone is buried in the rice tank for a while and then taken out to try, if it still doesn't work, it can only be repaired.

Can be repaired immediately disassemble with a hair dryer to dry or dry, after the end of the check hardware for damage, and then try to turn on, if it has not been turned on, that is, the hardware is broken to replace it.

During the maintenance period, the official can be repaired, but it is not free of charge, and the water will be repaired.

If you can repair it, first dry the water with an electric hair dryer on your mobile phone, and then take it to a designated maintenance station for maintenance.

If this circuit version is short-circuited, it cannot be repaired and will be scrapped! Let's let the professional repair check take a look!

It can be repaired, but it may be expensive, mainly depending on what is broken, and there is no need to repair the motherboard if it is burned.

If the Apple mobile phone can't be turned on, it's better not to repair it, the cost is too great, everyone knows that the Apple mobile phone costs seven or eight hundred to change a screen, and if the motherboard is broken, the least is more than 1000.

It can be repaired, but it is of little significance, the machine with water is easy to corrode, and the maintenance cost of the motherboard parts is high, so it is not recommended to repair.