AMD original fan disassembly, how to install Ryzen AMD original fan

It is silicone, and if you buy a brand machine or use it for a long time, it is not easy to unplug it.

Step 1: Use the machine for more than five minutes, remember to adjust the CPU usage to the highest, and then turn it off, take advantage of the time when the radiator is not cooled down, condense the cooling fan left and right, and pull it out hard--- of course, you can also use blowing to deal with it, and the effect is worse if it is not enough.

If you really can't pull it out--- I've encountered three or four such situations, don't think about it, pull it all down hard--- don't be afraid of damaging the processor and interface, no problem, the most important thing is to remember to pull it up vertically, don't let the legs bend, after pulling it out, use a blade, a little wider and thinner, slowly cut it between the CPU and the radiator, pry the CPU and fall off--- don't remember this job not too high from the desktop, put a soft thing underneath, The CPU will suddenly fall off the heatsink, and I adjusted the results for a long time for this bending position, and I tried this method four times, and it has not caused hardware problems, so I can rest assured that it is done.

The adhesive force of silicone can almost be ignored, it should be your radiator stuck in ** Check it well, silicone can't be 801, and it's impossible to be a good brother Hehe.

The metal buckle should be silicone if it can't be removed if it is completely loosened, but it doesn't matter with a little force.

The landlord used a paper cutter to insert it into the gap between the CPU and the fan, and slowly pried it open.

If the fan still works, turn on the machine for a while and then get it. Let the silicone heat a little so that it can be easily removed.

When the buckle is loosened, a flathead screwdriver is needed to push the iron shrapnel that crosses the fan in the middle.

The specific operation steps for installing the Ryzen AMD original Nalao fan are as follows:

1. First of all, apply the CPU thermal grease to the top of the CPU cover:

2. Then take out the fan you just bought and remove the parts:

3. Then install the bracket with a total of four screws

4. Then insert the rubber bracket foot into the card slot near the CPU, and then press the four black rubber screws to make the hole resistant:

5. Finally, install the fan, and then buckle the buckle to the bracket, so that you can successfully install the wind mu rotten fan

Necessary materials: computer case, AMD CPU, fan.

1. Open the case with AMD CPU and fan to reveal the AMD CPU, as shown in the figure below.

2. On one side of the fan, there is a fixed bayonet in the red color circle, and the fan will be loosened when you lift it up, as shown in the figure below;

3. You can also untie the bayonet of the other half with the method of touching the socks, as shown in the figure below;

4. After the side bayonet of the two bridges is untied, shake it from side to side first, and you can lift the CPU fan if it is loose, as shown in the figure below;

5. Finally, lift the fan completely and complete the whole step.

1.Shut down and disconnect the power supply, remove the fan power cord from the CPU fan connector on the motherboard, and if the fan has an RGB cable, remove the RGB cable from the CPU cooler and the RGB connector on the motherboard.

3.Unlock the fins from the mounting lugs of the kingpin slots, there is a clamp on the cam rod side.

4.Gently twist the CPU fan back and forth from side to side, slowly separating the heatsink from the CPU top cover.

5.Carefully lift the CPU cooler and remove the fan, the CPU should remain in the socket slot.

1.Shut down and disconnect the power supply, remove the fan power cord from the pin CPU fan header on the motherboard, and if the fan has an RGB cable, remove the RGB cable from the CPU cooler and the RGB connector on the motherboard as well.

3.Unlock the heatsink from the mounting lugs of the motherboard slot, which has a clamp on the cam rod side.

4.Gently twist the CPU fan back and forth from side to side, slowly separating the heatsink from the CPU top cover.

5.Carefully lift the CPU cooler, and the CPU should remain in the slot after removing the fan.

It's the CPU and the heatsink are very tight, this looks like a gentle shake of the heatsink left and right, you must be leisurely, slowly shake it down (I just pulled the radiator off with the CPU, but it is still good to install it), this is due to the long time silicone grease sticked, after the heat sink is removed, the lever next to the CPU slot can be lifted outward, and then you can remove the CPU, touch the tap water pipe or wash your hands before taking the CPU, be careful of static electricity in winter.