How telcos use their own routing after installing fiber

You need to set up poppe dial-up on the route, enter your telecom and password, and set DHCP to on, that is, automatically assign IP, and don't set IP and gateway on your own computer, you can get it automatically.

1. The network port (LAN port) of the telecom optical modem needs to be connected to the WAN interface of the router with a network cable (called the Internet interface in some routers). For the computer, connect the network cable to any of the LAN (1, 2, 3, 4) ports of the wireless router.

2. Set the IP address of the computer.

3. Set up a wireless router to access the Internet.

4. At this time, the router will automatically check the "Internet access mode", if it is detected: broadband dial-up Internet access - > you need to fill in "broadband", "broadband password" - click "Next".

5. Wireless settings.

Set the "wireless name" and "wireless password" on this wireless router

Extended content: Optical fiber communication is widely used as the best for information transmission due to its unique anti-interference, light weight, large capacity and other advantages. The use of existing transmission lines to lay fiber optic cables is the most economical and efficient.

Due to the advantages of large capacity, long distance and anti-electromagnetic interference, optical fiber communication is well adapted to the needs of today's power communication development. In particular, optical fiber composite overhead ground wire (OPGW), which combines the high mechanical, high conductivity and good corrosion resistance of aluminum-clad steel wire, effectively combines power overhead ground wire with communication optical fiber, so it has attracted the attention of the power system industry and has gradually been popularized and used.

The installation and setup of the router is as follows:

1.First, connect the line between the broadband modem and the computer of the router, and use a network cable to connect the LAN port of the broadband modem to the WAN port of the router.

2.After the line is connected, open a browser, enter the management address and management password of the router, and then enter the router background (the login address and login password of the specific router can refer to the manual or the label on the back of the router).

3.After logging in to the background, select Quick Settings, enter the password applied for from the network service provider, and go directly to the next step after the input is completed;

4.Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

<> details are as follows: The optical modem itself does not have a routing function (bridge mode), and directly connects the optical modem to the WAN port of the router with a network cable.

The router sets up the dial-up connection (PPPOE), input, password; Then set the wireless name and save the password.

If it is a regular telecom mobile or Unicom optical modem, the routing function has been turned on; Even if you don't have a router, you can connect to the wifi to go online, and then add the router to set it up in 2 steps.

First, the router is not connected to the optical modem, directly enter the management interface, set the Internet modem: automatically obtain the IP method, and then set the wifi name, password, and save.

If the IP address of this router is not a network segment, you can directly plug in the network cable and connect it to the optical modem.

If the IP address is the same, you need to reconnect to the Wi-Fi, enter the management interface again, and set the third digit of the LAN port IP address to not be the same as that of the modem (to prevent conflicts with the IP address of the optical modem, resulting in Internet access at that time, but you can't access it after a period of time).

After setting OK, save it, and then use a network cable to connect the modem to the router to use.

There should be an optical transceiver (optical fiber receiver) at the end of the optical fiber.

Add a small switch (about dozens of yuan) between the optical transceiver and the fast router, and then connect a network cable to the TV set-top box on the small switch. Connect another network to the small switch.

fast circuit, which is used to access the Internet.

After connecting in this way, there should be three network cables on the small switch, one to the optical transceiver, one to the router, and one to the TV box.

For the specific settings of the route, you can refer to the route manual. If it is helpful to you, please be prompt, and if you don't understand something, you can continue to ask.

Telecom fiber optic modem with network cable to connect with the router, before setting the router to know whether the optical modem has been dialed, has dialed as long as the router is set to bridge, and then set the wireless name and wireless password can be used, if there is no dialing, the router should be set to dial, enter the broadband password and then set up wirelessly.

Don't be in a hurry to connect with the optical modem, connect the router to the computer first, press the address behind the router to open it in the browser, set the broadband and password, and set the name of the wifi SSID and password. Then take a look at whether the address of the optical modem and the router conflict, change the router address if there is a conflict, and then connect the LAN port of the fiber modem to the WAN port of the router, and connect the LAN port of the router to the computer...

1. Open a browser and enter in the address bar.

2. Enter the administrator password, click "OK", you don't need to apply for a password for the first time, you can set the password directly. If you do need to enter the password, look for the original password in the manual.

3. Once you're on the router, select "Setup Wizard".

4. Click "Next".

5. Select the dial-up option for broadband and click "Next".

6. Enter the account number and password provided by the network ** provider, and click "Next".

7. Click "Done".

The operation method of optical modem to wireless router is as follows:

1. Connect the network cable from any LAN port of the optical modem to the WAN port of the wireless router, and connect the network cable from the LAN of the wireless router to the computer, and automatically obtain the local connection IP address and DNS settings;

2. After powering on the wireless router, connect the computer to the wireless router and change the LAN address IP to avoid conflicts between the IP of the optical modem and the network segment address of the wireless router.

3. Open the browser, enter enter, enter the management username and password (the login address, management username and password are indicated on the back of the wireless router), confirm, and log in to the wireless router settings interface;

4. Setup wizard, next, select PPPoe dial-up mode, next, enter the Internet account and password, next, set the wireless network name in the SSID box, enter at least 8-digit wireless network password in the psk box, next step;

5. Save and restart the wireless router according to the prompts.

Next, configure the wireless function of the router and enter the IP address of the router in the browser.

Enter the router password to log in to the router.

Select the Internet settings option as shown in the image below.

Select Static IP, set IP address to IP address, subnet mask to subnet, gateway to set to, and finally set local DNS.

Select the Wireless Settings tab, turn on WiFi, set its name and password.

Finally, click the Advanced Settings tab, select the Intranet Settings option, and change the LAN port IP address to.

After saving the settings, connect the router to the Fiber Modem, and the wireless network of the Telecom Fiber Modem is set up.

If you have any other questions, you can also log on to the telecommunications online business hall (consultation).

The landlord bought the same TP as me, yours is fully automatic, right? Just plug it in, and then buy a network cable that is plugged into your router at one end, and plugged into this wi at the other end, which can be connected directly and automatically, no need to set up.

My home is also an optical modem + router, please try it as follows:

1. Turn on the modem device to ensure that the optical fiber is connected normally.

2. Enter the router setting page, and set the PPPOE link account and password according to the setup wizard.

3. If you need to set up the wireless network, you also need to configure 4. Connect the WAN port of the router to the LAN port of the optical modem, and wait for the router to dial up or restart the router.

Broadband can be installed wireless router use, wireless router needs to be hardware installation and parameter setting, the installation and setting method of the router is relatively simple, the following takes the fast router as an example to introduce the installation and setting method, and the setting method of other brands of routers is similar.

2. Then open the browser and enter the management address and login password of the router.

5. After the wireless setup is completed, click Save, and then restart the router to use it normally.

Fiber-to-the-home, optical modem to connect to the wireless router method:

1.Connect the WAN port of the router to the LAN port of the optical modem with a network cable, and when the WAN port light of the router flashes, the connection is normal.

How to configure a wireless router wifi:

1.The system is connected to the router.

Turn on the wifi of the computer, search for the default wifi name of the router (the nameplate on the back of the router is written), and connect to the wifi network. The first time you use the router, you generally don't need to enter the wifi password.

2.Go to the gateway page.

Open a computer browser and enter the gateway IP address of the nameplate on the back of the router (generally, enter the gateway configuration interface. (This interface will pop up automatically for new routes).

3.Set up a way to access the Internet.

Go to the WAN port settings in Advanced settings. If the broadband service requires dial-up, select PPPoE dial-up, otherwise you can choose DHCP to get automatically. To dial up PPPoE, enter the broadband account password, and select Automatic connection as the connection mode.

If DHCP is automatically obtained, you do not need to enter this field.

4.Set the wifi name and password.

Go to Wireless Security in the Wireless Settings and select WPA2-PSK mode for Security Mode. Select AES for WPA encryption rule. Set up a wireless network key. The router will automatically restart after setting, please enter a new wifi password to connect.

Telecom will provide you with a broadband account for Internet access, take TP-Link as an example, the router plugs the incoming cable of Telecom into the WAN port of the router and plugs it in. Pay attention to the IP address and account password identified on the back plate of the router, and connect the mobile phone to the WiFi released by the router. Open a browser, enter the IP address of the router backplane, open the router management interface, and log in with the default account and password of the router.

Then follow the instructions to set it step by step, select PPOE to fill in the broadband account password given by China Telecom. Then, set the wifi name and password to it. If it's troublesome, just add a password without changing the name.

The method of telecom broadband connection router is the same as that of other broadband connection routers, you only need to connect the fiber modem and the router, and then enter the router settings page to set up.

The above information is for reference only, gigabit in the city, C-position debut. 5G dual gigabit**, 1000M broadband, 60G traffic for the whole family, details can be found in Guangxi Telecom's online business hall. Customer service number 192 will answer for you.