Why does the bathroom heater keep flashing when you replace other lights?

The heater in the bathroom keeps flashing after replacing it with other lights, it may be that the circuit is in poor contact, and it is best to reinstall and debug.

The bathroom heater is replaced, why do other lights keep flashing? Maybe it's a virtual connection, or the line shouldn't be connected with the light wire, so this problem arises, let's change the line.

It means that the lamp that is replaced does not match the original line and needs to be replaced.

Nan Fengdun on the bathroom was replaced, and the other lights kept flashing, which may be that the line was not connected well and the contact was poor.

This may be because the light is originally short-circuited and the wiring is not good.

It is possible that the power of your bathroom heater is too high, or it is in poor contact, resulting in poor contact of wires.

If the other lights in the bathroom keep flashing, it means that he has poor contact. You put that lamp back on and see what the reason is. Be sure to stay safe.

Its light has been on, indicating that it has a problem or malfunction, it is recommended that you check it, otherwise it will reduce your full score life.

The bathroom heater has been replaced, and the other lights have been flashing, which means that the lamp is not suitable for this voltage, so do you see if the voltage is too large or too small? Appropriate replacement.

Hello, friends bathroom heater replacement on the other has been flashing, this is the connection. There may be a problem, or something, or a stupid all the time, I hope it can help you.

If you change to the southern base, just say that other things plant mountains and mountains means that you are in the room after the power is too much, this is the hotel may have five places to leak electricity to cause this other thing to plant flickering, non-stop, I think you should find an electrician to repair it.

The fan has been flashing all the time due to poor contact, probably because of poor contact.

If it keeps flashing, it may be because they don't match, or maybe one of your switches is turned on, so he keeps flashing.

This is a poor contact, or the control is at the zero line, and this will happen.

If the light keeps flashing back and forth, it should be wired or the switch is off, so check it quickly.

The flashing light on the bathroom heater is caused by poor contact.

This should be a wiring issue.

Use common lines with each other.

All have an impact.

Why does the bathroom heater keep flashing when you replace other lights? This is based on a fixed power and various conditions. So sometimes it doesn't have to be unmatched.

The heater in the bathroom has been replaced, and the other lights have been flashing, which means that the bulb has poor contact and it is best to use the original type of lamp to pay attention to safety.

Why does the bathroom heater keep flashing when you replace other lights? It may be that the wire of this lamp cannot be contacted, so it will flash all the time.

It may be that the wiring is plugged in, and you ask the electrician to check it for you, or how the renovation worker gave you the wiring at that time.

Why do other lights keep flashing in the bathroom in the warm winter, it may be due to poor contact?

That's a lack of power, or yours and say there's something wrong with telecommunications.

The bathroom heater keeps flashing when other lights are replaced, first of all, this has a certain relationship with his power.

Summary. Why does the light on the heater flash when the ventilation switch is turned on, there are many reasons why the wind heater bath bomb light flashes, it may be that the filament inside the air heater bath bomb lamp is damaged, if it is determined that the filament is damaged, the lamp needs to be replaced. 2.

It is also possible that the wire of the wind heater lamp is not in good contact with the wind heater bath bomb lamp, which depends on the specific situation, you can open the pipe of the lamp, check if there is any poor contact, and then reconnect it. 3.If there is a problem with the air heater bath bomb lamp, it should be repaired in time, and don't think that it can be used if it is improvised, because if the wiring of the lamp has poor contact, if it is not repaired for a long time, it may cause a short circuit and cause danger.

Hope it helps. If my answer is helpful to you, please give a thumbs up (in the lower left corner), I look forward to your like, your efforts are very important to me, and your support is also the motivation for my progress. Finally, I wish you good health and a good mood!

Good. Why does the light on the heater flash when the ventilation switch is turned on, there are many reasons why the wind heater bath bomb light flashes, it may be that the filament inside the air heater bath bomb lamp is damaged, if it is determined that the filament is damaged, the lamp needs to be replaced. 2.

It is also possible that the wire of the wind heater lamp is not in good contact with the wind heater bath bomb lamp, which depends on the specific situation, you can open the pipe of the lamp, check if there is any poor contact, and then reconnect it. 3.If there is a problem with the air heater bath bomb lamp, it should be repaired in time, and don't think that it can be used if it is improvised, because if the wiring of the lamp has poor contact, if it is not repaired for a long time, it may cause a short circuit and cause danger.

Hope it helps. If my answer is helpful to you, please give it a thumbs up (comment in the bottom left corner), look forward to your like, your efforts are very important to me, and your support is also the motivation for my progress. Finally, I wish you good health again, and you will be happy with envy!

Summary. Hello dear! Dear, I am glad to answer for you the reasons why the bathroom air and heating integrated ceiling lights are flashing and flashing as follows:

There was a problem with the contact of the power supply, causing the integrated lights to flicker and blink. 2. The constant current IC inside the drive power supply is damaged and cannot operate normally. 3. This phenomenon will also occur when the electrolyte in the filter capacitor dries up.

4. The filtering performance of the integrated lamp is reduced, which will also cause the lamp to flicker and flicker.

Hello dear! Dear, I am glad to answer the reason for the flickering of the bathroom air heating integrated ceiling lamp as follows: the contact of the power supply is slow, and the problem of Lubi appears, resulting in the integrated lamp flashing and flashing.

2. The constant current IC inside the drive power supply is damaged and cannot operate normally. 3. The electrolyte in the filter capacitor will also appear when it dries up. 4. The filtering performance of the integrated lamp is reduced, which will also cause the lamp to flicker and flicker.

The flashing of the ceiling lamp is generally caused by the poor contact of the power supply line, the constant current IC failure of the driving power supply, the drying up of the electrolyte inside the filter capacitor, and the decrease in the filtering ability. The ceiling can be opened, the power supply orange source line can be reconnected, or the constant current drive power supply or filter capacitor of the same model can be replaced.

In this case, the main power supply should be turned off and closed, and then the ceiling should be disassembled, and the power supply line of the ceiling lamp should be re-checked, and if it is not connected, it should be re-connected. Or replace the same type of constant current drive residual retarded power supply and filter capacitor.

If the light on your bathroom heater is broken, you can consider the following ways to replace it:

1.Prepare tools: Prepare some necessary tools, such as electric pens, snail knives, etc.

2.Power off: Make sure to disconnect the power supply before replacing the light.

3.Open the case: Locate the screws on the case and unscrew them with a screwdriver.

4.Replace the bulb: Remove the old bulb and install a new bulb.

5.Reinstall the chassis: Reinstall the chassis back in place and secure it with screws.

6.Power on: Finally, plug it in again and check if the new bulb is working properly.

If you are not familiar with electrical maintenance, please consult a professional or letter person to avoid accidents.

1.Locate the heater light: Locate the location of the heater light and determine if it is within the service range.

2.Look for repair tools: Have repair tools ready, such as screwdrivers, wire scissors, etc.

3.Remove the old heater with fan light: Use a screwdriver to remove the housing of the old heater light, and then remove the bulb or tube.

4.Connect the new heater light: Use wire shears to cut the wires of the new bulb or tube short to connect it with the wires of the heater lights.

5.Install a new heater light: Reinstall the heater light's housing back and connect the new wires to the heater light's wires.

6.Check the connections: Make sure the connections are secure and not loose or damaged.

7.Install a new heater light: Reinstall the heater light's housing back to make sure it's secure, and then restart the heater light.

Please note that replacing a heater light may require some technical knowledge, and if you are unsure how to remove or install it, seek the help of a professional.

The bathroom heater turns on the hair dryer and keeps flashing, and the le light does not flash after it is taken off the keel.

Hello cavity. For you to find out: the reasons for the broken bathroom heater are as follows; 1. There are many reasons why the air heater bath bomb lamp flashes and flashes, it may be that the filament inside the wind heater bath bomb lamp is damaged, and if it is determined that the filament is damaged, the lamp tube needs to be replaced.

2. The flashing of the air heater bath lamp may also be due to the poor contact of the wire connection of the wind heater bath bomb lamp, which depends on the specific situation, you can open the pipeline of the lamp, check if there is a poor contact, and then reconnect it. 3. If there is a problem with the air heater bath bomb lamp, it should be repaired in time, and don't think that it can be used if it is improvised, because if the circuit of the lamp has poor contact, if it is not repaired for a long time, it may cause a short circuit and be dangerous.

Summary. Hello, <>

This question is being answered for you, you need to wait patiently for about three minutes, and the answer will be revealed for you immediately, please don't worry! <>

Why does the light on the heater flash when the ventilation switch is turned on?

Hello, <>

is answering this question for you, Shanshan you need to wait patiently for three minutes or so in the dust, the answer will be revealed for you immediately, please don't worry! <>

Maybe your fan power is larger, the instantaneous current at the start of the excavation is larger, and the wire is relatively thin, resulting in an instantaneous voltage drop, affecting the normal use of the lighting, check the power of the wire and the fan to change the start of the fan to "soft start" can reduce the mutual impact. There is also a possibility that the stability of the lighting is poor and the anti-interference ability is poor.

Solution: Check whether the filament is damaged, if it is necessary to buy a new lamp, remove the old lamp and replace it with a new lamp. If it is caused by the defective contact of the wire, it is necessary to turn on the light first, and check its pipe condition, first determine the poor contact, and then reconnect it.

Hello, <>I hope the above is helpful to you If you are satisfied with me, please give a follow-up <>

Thank you.