TP Link broadband Internet access can not always be connected urgently

If you can dial up directly to the Internet, it means that there is no big problem with telecommunications, but there is a situation that may occur that this line is also connected, although it can run at the same time, but sometimes it can't run at the same time, I have encountered this situation many times, anyway, it is not possible to dial up with the route, Telecom has also checked many times, said that there is no problem, and then invited a senior engineer, after the line was tested, said that it was ** and the network has an impact, so it was removed, There is no problem with just using the network, see if this is the case with LZ.

It may be that the contact between the crystal head of the network cable and the slot of TP-Link is not good. My cat also has this problem,,, sometimes the signal light won't turn on if you move this thing a little.。。 You have to fiddle with your hands carefully. Until the lights come on.

1.Factory reset TP-Link and reset your Internet access parameters.

2.Enable the MAC address cloning function in TP-Link.

3.Check whether the local connection settings of your local device automatically obtain IP and DNS, and check whether the router has DHCP enabled.

3.If the above two steps are not enough, go to the TP-Link official ** to see if there is an upgrade program for your model, flash the latest program for the router, and then try again.

Connect to TP-link, and the message indicates that the Internet is not available.

Hello, according to your question, "Connect to TP-link, the prompt is not available on the Internet" will be answered by me, this is your router is not connected to the Internet or is in arrears. The solutions are as follows: 1. The router is unstable.

It is recommended to power off the wireless router and optical modem (broadband modem) at home, wait for a few minutes, and then turn on the power and start the device. After the normal start, connect to the wifi for testing. 2. Broadband failure.

First of all, call the customer service of broadband** to check whether the broadband is in arrears, and if it is in arrears, you can pay the fee. If there is no arrears, you can transfer to the manual customer service, report the fault, and ask the operator to arrange staff for repair. 3. The router is not connected to the Internet.

If there is no problem with the broadband line, there is no arrears in the bandwidth, and the broadband operator is not responsible for debugging the router. Untie. The solution is to check the relevant configuration in the router, you can use a computer or mobile phone, log in to the settings page of the router first, find and open the option of Internet access settings or WAN port settings, and you can see the network status information of the router.

The settings are correct: Select PPPoE dial-up mode? Is the username and password entered into the broadband correctly? IP and DNS selection provided by ISP? Enable DHCP?

Go to the wireless router settings page.

Check the WAN port settings, if the account and password are correct, you should be able to connect to the Internet.

--The broadband network cable should be plugged into the WAN port.

My family often has this problem.,Pick up the route,Try it directly under the ad box chain.,If you can access the Internet.,There's a recovery key behind the router.,Pestle.,It's equivalent to starting the router.,It's good.

This is often the case with TP-Link.

Factory reset the data in the route.

Wireless router TP-Link settings connection network method:

Home Network Environment Cabling]:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoE Dialing] (some are ADSL dialing), enter the username and password (provided by the network service provider) according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit. Turn on the wireless function of the router

1. Select Wireless Settings --- Basic Settings.

2. Check [Turn on wireless function] and click Save.

Set wifi password].

1. Wireless Settings - Wireless Security Settings - Select [WPA-PSK WPA2-PSK].

Authentication Type: Automatic.

Encryption algorithm: AES.

The PSK password is the wireless password. Set the required password.

Some places are restricted from using the router, clone the MAC address to try, if it doesn't work, you just call ** to the customer service center to let him unbind your broadband on the line Sometimes it's not necessarily a routing problem You let the customer service center refresh your network port.

If you are sure that you have not changed the IP address, the default address is , if it is normal, it should open a login page, and you can enter ping under the command prompt to see if the network is normal, if it is not normal, restore the factory value according to the manual, and try to reconfigure.

Once configured, your router name will be found on your computer's wireless network and connected.