The computer freezes and then the problem arises, what is the reason for the problem of the computer

Updated on number 2024-02-09
13 answers
  1. Anonymous users2024-02-05

    Your problem should be that there is a problem with your hard drive. Unless the hard drive and motherboard are not compatible. You set the hard drive to a compatible IDE mode and see. When your hard drive is installed on another machine, the blue screen is caused by the driver in your system and the driver in someone else's machine does not match the number.

  2. Anonymous users2024-02-04

    I've had similar problems with my computer before, one case may be a problem with the graphics card, or it may be a problem with the memory module. I didn't find anything wrong with the computer before I took it to the repair point, and it ran well when I got it to the store. I suggest you go to a repair shop to get a graphics card to try first, and you say I'll take it back and try it first, and buy it if I can use it, and the general store owner will be willing.

    Hope it helps.

  3. Anonymous users2024-02-03

    Most of these problems are related to the motherboard and hard disk, first change the hard disk to your computer and try it, if there is such a problem, it must be the problem of the motherboard, there may be a problem with the interface of the motherboard.

  4. Anonymous users2024-02-02

    Start by looking at the line issue. Try to change the data cable between the hard disk and the motherboard, and then change it to another hard disk to try it, if it still appears. The problem with the motherboard is the greatest.

  5. Anonymous users2024-02-01

    I guess the problem should be on the hard drive. Do you first find another hard disk and give it a try to see if there is a problem with your motherboard slot or a hard disk Have you detected bad sectors on the disk? If it really doesn't work, just change it. . .

    Now the hard disk is also very cheap, 500g** is also around 260.

  6. Anonymous users2024-01-31

    If the motherboard battery has been replaced, the BIOS imports the default settings, if the hard disk is fine, it should be solved, you can borrow a hard disk to try it, sometimes this is such and such a problem that is not easy to find.

  7. Anonymous users2024-01-30

    I've had this problem before, I haven't found it for a long time, and then I found that the CPU was loose, and some of the pressure sticks inside fell off, and it was good from installation.

  8. Anonymous users2024-01-29

    There should be a problem with your hard disk partition table, just use software to repair the partition table.

  9. Anonymous users2024-01-28

    Check the hard drive with HD Ture, I'm afraid there is a problem with the hard drive.

  10. Anonymous users2024-01-27

    Put the small fan of your computer、Replace it、OK

  11. Anonymous users2024-01-26

    1: The most common is that there is too much dust and the temperature is high.

    2: The system file is corrupted.

  12. Anonymous users2024-01-25

    The motherboard or CPU fan is not working, the hardware temperature is too high, the process occupies too much physical memory, and if your processor is not powerful, it will die.

  13. Anonymous users2024-01-24

    Lao Tzu wishes that I will not repeat the correct solution.

Related questions
11 answers2024-02-09

There are many reasons, which are divided into software failures and hardware failures, 1. Hardware. >>>More

9 answers2024-02-09

It is unlikely that a computer crash in the DCS system will cause the entire network to be paralyzed, but it should be caused by a defective design, or an error in the communication settings or communication cables. The initial inference is that it is a communication failure, please investigate whether the computer crashes or the communication failure first, whether the DCS controller and the indicator lights of each module are normal, whether the switch is normal, whether the network cable and connector are intact, rule out the cause of the switch and module, and then lock the problem on the computer, check the correct computer software settings, and then check the hardware, focusing on the network card, some DCS systems will monitor the network when designing, and execute the corresponding procedures. >>>More

14 answers2024-02-09

Remove the system, implicit and read-only attributes of the Chinese part of the C drive. >>>More

43 answers2024-02-09

As mentioned above, the crash is caused by hardware or software. >>>More

20 answers2024-02-09

It is likely that there is a problem with the memory part, unplug the memory and rub the gold finger with an eraser, and then try another slot, and try to change the memory if it still crashes.