I have a wireless router installed in my house, but the wired can t be used, what s going on

Let's take a look at it step by step.

First of all, you said follow the steps to set it up. I don't know if you're really set it up. It is recommended to add a name to your wireless network and then set a password when setting it up.

Prevent others from occupying your home's broadband. And you can verify that your computer is connected to its own route, and you need to turn on DHCP. Open the SSID.

So that the computer is set to automatically get the IP. The specific settings are the same as those of a wired NIC. Then there's the wireless internet signal.

It's best not to leave the laptop away from the router with two walls. Walls may block out the signal.

There is also the issue of DNS address setting. See if your computer can get on Q no, if you can get on Q. If you can't access the Internet, it's a DNS setting problem.

You say it's plugged into the bus. What a concept. If the line is fine.

I think the parameters of your wired network card are not set correctly, the specific steps:

Double-click View Network Connection --- on the left side of the Internet Neighbor --- right-click on the local connection--- Properties--- Internet Connection Properties--- all set to Automatic.

Then dial up to surf the Internet.

Do you have a cat connected to your home? If you don't connect, that's not going to work.

If you can get the IP address assigned by the router normally, then you can see if the DNS is the same as the local DNS, there may be two kinds of online inaccessibility, one is that you can QQ can not web page is a typical DNS problem, and the other is that you can't QQ can not web page, this is to see if you can get the IP of the router, whether you can get ping or not, it is an intranet problem, and then clone the MAC address in the router once.

The problem is too rough, not good, just guess one, the desktop originally set the IP address, now the router is changed, not in a network segment, can not access the Internet, the solution, change the IP address of the desktop to automatically obtain or specify and route the IP of a network segment. This is provided that the line and routing settings are correct.

This does not require an IP address, it can be changed to automatically obtain. The notebook can be used with a desktop, and it will definitely work.

Summary. Hello,A wireless router under the wired router belongs to the secondary route,It needs to be set up correctly to access the Internet,It is estimated that the situation encountered by the subject should be caused by IP address conflict。

My wired router at home has wireless function, but it can't get online after connecting, why ???

Hello,A wireless router under the wired router belongs to the secondary route,It needs to be set up correctly to access the Internet,It is estimated that the situation encountered by the subject should be caused by IP address conflict。

Method Step 1 6 Secondary Router Setup Method The current wired router has been set up and can access the Internet, we only need to set up the wireless router, and the first two routers cannot be connected, the specific setting method is as follows: 2 6 First, modify the IP address of the LAN port. Use your mobile phone to connect to the wireless signal sent by the wireless router, enter the management address of the router in the browser (look for it on the back of the router, the general management address is, enter the LAN port setting on the router management page, modify the IP address to, save and restart.

3 6 Second, set the wireless network parameters. Re-enter it in the browser of your mobile phone, enter the Wi-Fi settings on the management page again, set the wifi signal name and password, and click Save. 4 6. Turn off the DHCP service.

Reconnect the set WiFi signal, go to the DHCP service settings on the management page, turn off the DHCP service, save and exit. 5 6 Fourth, connect the main and secondary routers. Use a network cable to connect the LAN ports of the two routers, note that the LAN ports of the two routers are connected, and you can do it.

Have a great day.

How stable the network cable is! The signal of the router is not good...

First, check whether your router is set up to surf the Internet, such as ADSL dial-up fixed IP address. Second, see if your DHCP settings are turned on, after opening this, your laptop or mobile phone will automatically get IP and DNS!

As far as I can tell, there could be three reasons for this:

1: The router is not connected to the external network at all, of course, if it is wired and can access the Internet, this reason does not exist.

2: The network you are connected to belongs to the network that needs to verify the user, and you can ask the network provider for help.

3: In the router wireless settings inside, your access may be blocked Because the information you provide is limited, and I am not very professional, from experience, I can only put forward these 3 possibilities, I hope it can help you a little.

First of all, you have to log in to the router to check whether it has been connected to the network, that is, to check the status, if the WAN port is assigned an address, it means that it has been successfully connected, so you can check the wireless configuration.

After connecting the line, restore the router to factory settings, and then enter the settings interface according to the address provided, set the account and password to save and exit. If there is a successful connection icon (in green) below the computer, it means that the setup is successful. If you don't have access to the Internet, it's a problem with the line.