What is the exhaust temperature of an air conditioner, the exhaust temperature of an air conditioner

Refers to the gas in the compressor that is discharged from the combustion chamber and passed through the turbine rotating at high speed before being turbocharged in the engine.

Temperature on the outlet section. During the operation of the compressor, due to some reasons, the discharge temperature will exceed the normal value, which will not only cause the power consumption of the compressor to increase, but also make the lubricating oil charcoal, the performance will deteriorate, and the normal operation of the compressor will be affected.

In order to avoid excessive exhaust temperatures, the exhaust temperature can be controlled with an injection valve. Discharge temperature protection is one of the types of compressor temperature protection.

The exhaust temperature is the temperature of the exhaust gas after the compressor has done work, which can be measured from the exhaust pipe with a thermometer. The exhaust temperature is directly proportional to the pressure ratio and the suction temperature. The higher the pressure ratio and the higher the suction temperature, the higher the exhaust temperature.

In the refrigeration and air-conditioning industry, the so-called "exhaust temperature of the air conditioner" refers to the temperature of the refrigerant discharged by the air-conditioning compressor, which is generally measured on the exhaust pipe of the compressor at a distance of about 20cm from the exhaust port.

The exhaust temperature of an air conditioner compressor generally ranges between 65 and 95 degrees.

The air conditioning compressor has a condensing temperature when it is condensed, and the air conditioning compressor discharges the indoor heat to the outside when it is refrigerated, and the temperature of the heat discharged is the exhaust temperature, and the condensing temperature corresponds to the exhaust temperature.

Generally, air conditioners will encounter faults where the exhaust temperature is too high.

There are two main factors for the high exhaust temperature, one is that the outdoor condenser is dirty or the fan is aging, and the condensation efficiency is low; Second, the system has air.

If the exhaust pressure is too high, there will be a high-pressure and high-temperature alarm, and the compressor will stop.

The solutions are: clean the outdoor condenser fins and check whether the fan is normal; If it is still high, the system will be evacuated, and then refrigerant will be added after vacuuming.

The air conditioning compressor has an evaporation temperature and a condensing temperature, the condensing temperature corresponds to the exhaust temperature, and the air conditioner can refrigerate, at the cost of discharging the indoor heat to the outside, and the temperature of the discharged heat is the exhaust temperature.

Exhaust temperature: The industry standard recognizes the temperature of the high-pressure pipe (thin pipe) output of the compressor exhaust pipe, and the exhaust temperature sensor is set here. Generally 138°CNormal is 80-90°C

Machines beyond this limit generally go into protection and show a fault**.

The reason is mostly that the condenser is too dirty, less fluorine, and the capacitance of the outdoor fan is faulty.

That is, the high-pressure outlet temperature of the compressor of the outdoor unit.

I know that. "Air conditioning exhaust temperature" in the refrigeration and air conditioning industry, refers to the temperature of the refrigerant discharged by the air conditioning compressor, which is generally measured in the compressor exhaust pipe, and the temperature is measured about 20cm away from the exhaust port. The normal range of air conditioning compressor discharge temperature is 65 95.

The high exhaust temperature is mainly due to two factors. First, the outdoor condenser or fan is aging, and the condensing efficiency is low. Secondly, you have air.

If the discharge pressure is too high, there will be a high-pressure and high-temperature alarm, and the compressor will be shut down. The solution is: clean the outdoor condenser fins and check whether the fan is bent normally; If the fan is still high, the system will be deflated, vacuumed and snowed.

In general, the exhaust air temperature fluctuates between 60 and 110 degrees, because the ambient infiltration temperature is different from the indoor temperature; Regardless of the type of refrigerant, there is little difference in exhaust air temperature under specific operating conditions; 90 100 degrees in cold and 80 105 degrees in heat. Under normal circumstances, the air conditioner is refrigerated, and the temperature of the air outlet should be what degrees.

12 15 The outdoor ambient temperature of the refrigerated air conditioning unit is about 35, and the actual indoor air temperature is about 27. When the refrigeration mode is running, most of the outdoor air outlet and spine temperature of the indoor unit are lower than 15. If the temperature of the air outlet of the indoor unit exceeds 16, it means that the pipeline status of the air conditioning system is abnormal, and the air conditioning unit needs to be inspected and maintained as necessary.

Refers to the temperature of the hot air that is exhausted from the outdoor unit of the air conditioner. When the air conditioner is working, the indoor unit absorbs heat and cools the indoor air, and then transfers the heat to the outdoor unit through the refrigeration cycle, and finally discharges the hot air. The exhaust temperature is the temperature of the hot air expelled from the outdoor unit of the room, which can provide information about the working condition and efficiency of the air conditioning system.

If you touch Lingguo, you observe the air conditioning rowThe gas temperature is abnormally high or low, which may indicate a problem with the air conditioning system, such as poor refrigeration, refrigerant leakage, etc. In this case, it is recommended that you contact a professional aircon repairer for inspection and repair. They can evaluate the air conditioning system and take appropriate measures to fix the problem.

The exhaust temperature of the air conditioner refers to the temperature of the refrigerant transmitted from the indoor unit to the outdoor unit. Generally speaking, the exhaust temperature of an air conditioner will vary depending on the working principle of the system such as compression and shrinkage, expansion, and refrigeration in the air conditioning system. Depending on the conditions, the exhaust temperature of the air conditioner may vary between -15 and 30.

In general, the lower the temperature in an air-conditioned room, the higher the exhaust temperature. In addition, when the heat is the same, the working efficiency of the air conditioner and the exhaust temperature are inversely proportional.

The exhaust temperature of the air conditioner refers to the temperature of the gas discharged by the indoor unit of the air conditioner after inhaling the air from the rubber trapped room, and after being treated by the condenser and the evaporation beam reader. The exhaust temperature is usually used to measure the efficiency and performance of the air conditioner, and in general, the exhaust temperature should be between 12-20 degrees Celsius. If the exhaust temperature is too low, it means that the cooling effect of the air conditioner is too strong, which will cause the indoor temperature to be too low; If the exhaust temperature is too high, it means that the refrigeration effect of the air conditioner is not good, and it needs to be repaired or repaired.

An excessively high air conditioner exhaust temperature can be caused by a variety of reasons, and here are some common causes and solutions:

Pipe blockage: When there is a blockage in the air conditioning duct, the outdoor unit cannot absorb air normally, resulting in the exhaust temperature being too high. The air conditioning line can be cleaned or unblocked to restore the smooth flow of the pipeline.

Fluorine nozzle expansion valve blockage: When the fluorine nozzle or expansion valve is blocked, it will cause the refrigerant to not enter the evaporator for evaporation. This causes the temperature of the condenser to rise, which leads to an excessively high exhaust air temperature. The appropriate fluorine nozzle or expansion valve needs to be replaced to normalize.

Insufficient refrigerant: Insufficient refrigerant dosage in the air conditioner can also lead to excessively high exhaust temperatures. Refrigerant can be added to solve the problem.

Compressor damage: When the compressor is damaged, the exhaust temperature rises dramatically. The compressor needs to be replaced to solve the problem.

Prevent electronic control components with caution: Faulty electronic control components of an air conditioner can also lead to excessively high exhaust temperatures. Faulty electronic control parts can be replaced to resolve the issue.

In short, if the exhaust temperature of the air conditioner is too high, you need to make a correct judgment in time and take corresponding measures. If you are unable to resolve the issue on your own, consult a professional service professional for diagnosis and repair. Note that not properly handling the direct interface will cause more damage.

The higher the suction temperature, the higher the compression ratio, and the higher the exhaust temperature.

The compressor should run normally within the scope of use, and there should be no high temperature of the motor and too high exhaust temperature. Compressor overheating is an important fault signal that there is a serious problem with the refrigeration system or that the compressor is not being used and maintained properly.

High air conditioning exhaust temperatures can be caused by a variety of factors. First of all, it may be caused by insufficient refrigerant or air leakage in the air conditioning system. In this case, it is recommended to contact a professional air conditioning maintenance engineer in time for overhaul and maintenance.

Secondly, it may be that the compressor of the air conditioning system is malfunctioning, resulting in an excessively high exhaust temperature. In this case, the compressor needs to be replaced or repaired.

In addition, if there is too much dust or blockage near the exhaust port of the air conditioner, it will also cause the exhaust temperature to be too high. It is advisable to clean the air conditioner exhaust and its surrounding area regularly to ensure good air circulation.

In short, the high exhaust temperature of the air conditioner is a problem that needs to be dealt with in time. In order to ensure the normal operation of the air conditioner chain and prolong the service life, we recommend that the air conditioning system be inspected and maintained regularly.

Summary. Hello, I'm glad to answer for you: The solution to the high exhaust temperature of the air conditioner is:

1.Find coolant leaks and fix them. 2.

Replace a damaged compressor or repair a damaged circuit part. 3.Clean the air conditioner's evaporator to ensure that it can effectively absorb and dissipate heat.

4.If you are using an air conditioner, you also need to check the connection of the pipes. <>

The reasons for the excessive exhaust temperature of the air conditioner are: 1. There is a coolant leakage inside the air conditioning system, resulting in poor refrigeration effect. ,2.

The air conditioner compressor is faulty or has a circuit problem that prevents the compressor from working properly. 3.The air conditioner evaporator is clogged or contaminated, resulting in heat not being effectively absorbed and dissipated.

How to solve the high exhaust temperature of the air conditioner.

Hello, I'm glad to answer for you: The solution to the high exhaust temperature of the air conditioner is:1

Find coolant leaks and fix them. 2.Replace the damaged compressor or repair the damaged circuit parts.

3.Clean the air conditioner's evaporator to ensure that it can effectively absorb and dissipate heat. 4.

If you are using an air conditioner, you also need to check the connection of the pipes. <>

The reasons for the high exhaust temperature of the air conditioner are: 1. There is a leakage of cold front agent in the air conditioning system, resulting in poor refrigeration effect. ,2.

The air conditioner compressor is faulty or has a circuit problem, so that the compressor can not work properly. 3.The air conditioner evaporator is clogged or contaminated, resulting in heat not being effectively absorbed and dissipated.

Does capillary blockage affect the compressor exhaust temperature being too high?

Dear, capillary blockage is too high to affect the compressor exhaust temperature. In compressors, the capillary is a key component used to control the flow of refrigerant in the form of a refrigerant. If the tubules are clogged, the refrigerant flow is restricted, resulting in reduced refrigeration efficiency. <>

Hello dear <>

Excessive exhaust temperature of the air conditioner can be caused by the following reasons:1The air conditioning system is overloaded or overloaded, and it is necessary to reduce the air conditioning time or reduce the load, such as shutting down some unnecessary equipment or reducing the heat source in the room.

2.The aircon filter is clogged with dust or debris, resulting in poor air circulation, and the aircon filter needs to be cleaned or replaced regularly. 3.

The refrigerant in the air-conditioning system is insufficient, and it is necessary to contact professional air-conditioning maintenance personnel to add refrigerant. 4.The outdoor ambient temperature is too high, and the air conditioning system needs more energy to lower the indoor temperature, and the Zen limbs cause the temperature of the exhaust air to rise, so it is necessary to reduce the indoor temperature as much as possible, such as using shade curtains or increasing indoor ventilation.

Hello dear<>

Sorry for your question. The reasons for the high exhaust temperature of the air conditioner are as follows: 1

Internal failure of the air conditioning system: Components inside the air conditioning system may fail or be damaged, causing the exhaust temperature to rise. The solution is to ask a professional aircon repairer to check and repair the fault.

2.Water-cooled system problems: In the case of water-cooled air conditioning systems, it may be that the water pump, cooling tower, or cooling water circulation system is faulty, resulting in poor cooling and increased exhaust temperatures.

The solution is to check the operating status of the water cooling system and repair or replace the faulty parts. 3.Air conditioning system overload:

If the air conditioning system is operating under excessive load, it may cause the exhaust temperature to rise. The solution is to reduce the load on the air-conditioning system, such as adjusting the temperature setting, increasing the cooling dose or increasing the heat dissipation area of the radiator. 4.

Insufficient refrigerant: If the refrigerant in the air conditioning system is insufficient, it will lead to poor cooling and an increase in the exhaust temperature. The solution is to add enough refrigerant, which can be operated by a professional air conditioner maintenance personnel.

5.Aging of air conditioning equipment: After being used for a long time, air conditioning equipment may deteriorate or wear out, resulting in a decrease in refrigeration effect and an increase in exhaust temperature.

The solution is to maintain and maintain the air conditioning equipment in a timely manner, and regularly clean and replace the parts that need to be replaced. If you encounter the problem of high exhaust temperature of the air conditioner, it is recommended to contact a professional air conditioner maintenance personnel for inspection and maintenance in time to get an accurate solution. Do not disassemble or repair the air-conditioning equipment by yourself to avoid further damage or safety hazards.

I hope my answers can help you, and I wish you a happy life<>

Summary. Hello dear, happy to answer your <>

Overpressure in the system needs to be checked and treated, whether it is too much refrigerant or the compressor is overworked. 2.The pressure of the air conditioning system is too low:

The low pressure in the system needs to be checked and treated, it may be that the amount of refrigerant is insufficient, or there is an air leak in the system. 3.Air conditioning system blocked:

Blockages in the system need to be checked and addressed, whether it is a clogged aircon filter or dust and debris on the surface of the condenser. 4.Air conditioning system failure:

It is necessary to inspect and deal with the failure of various critical components in the system, such as compressors, condensers, evaporators, etc. <>

How to solve the high exhaust temperature of the air conditioner.

Hello, dear, I am glad to answer the <> of [Xianchai Fanhua] for you

Overpressure in the system needs to be checked and treated, whether it is too much refrigerant or the compressor is overworked. 2.The pressure of the air conditioning system is too low:

The low pressure in the system needs to be checked and treated, it may be that the amount of refrigerant is insufficient, or there is an air leak in the system. 3.Air conditioning system blocked:

Blockages in the system need to be checked and addressed, whether it is a clogged aircon filter or dust and debris on the surface of the condenser. 4.Air conditioning system failure:

It is necessary to inspect and deal with the failure of each critical component in the system, such as compressors, condensers, evaporators, etc. <>

Here are some <> related extensions that we hope you will find helpful

Here are some things you can try:1Clean the air conditioner filter early and keep the air conditioner vents clear.

2.Check whether there is dust and debris on the surface of the air conditioner condenser, and test run it after cleaning. 3.

Check the air-conditioning system for air leaks, if there is any air leakage, you need to find a professional technician to deal with it. 4.Check whether the relevant parts of the air conditioning system are damaged or invalid, and if there is a problem, it needs to be replaced or repaired.

5.Re-inject the appropriate amount of refrigerant to ensure that the amount of refrigerant is within the normal range. 6.

Check whether the compressor is working normally, and if there is a problem, you need to find a professional technician to deal with it.