The problem of the Golden Wave router is 50 points and the points are also chased after the solution

You press the reset button on the router, press and hold, power on for about three seconds, I don't remember what the factory IP of this router is, you see for yourself, change your IP to, and the same network segment IP as him, for example: if the default IP of the router is, then you will set your computer IP to .

Reconfigure it after logging in, if you can't log in, it may be that the router is broken, you can replace it, and the router package is usually 1 year.

In addition, I will tell you that the router often drops due to the following reasons:

1.The router temperature is too high.

2.The router review is too heavy, such as the memory is too small.

The setting of only the main DNS, not the DNS of the device, is an important reason why the router often drops calls.

I've been in this situation a lot before.

Brother, your router may be broken, and if you can't even enter the interface of the management router, it means that your router is broken, you might as well try to change the router, if it proves that it is broken, take it and replace it as soon as possible, and it will not be replaced after the warranty period.

Can't log in to the router? You change the address, let's say or. .Wait, try it, my school's router will also change to this address, I don't know why.

Indeed, looking at your information, it's all normal.

Possible Questions:

1.incorrect account or password;

2.The connection between the broadband cat and the router WAN port, some broadband cats have a cross line, and if the router WAN port does not support automatic flipping, the lights will be on, showing that the connection is normal but the network cannot be connected, it is recommended to change an ordinary network cable to try;

3.The operator binds the MAC address of your Internet computer, which can be solved by using the router's "MAC address cloning" function, which is to copy the MAC address of the router to your computer.

A db ab cb cd dc ac bb cc cc ca two 1 analog signal, digital signal.

2 LAN, LAN, WAN.

3DHCP4 layer protocol and interlayer interface.

5. Interconnection layer, application layer.

3. 1(1) Set the IP address of the PC (router port) to and the subnet mask to (2) Set the IP address of the router to .

2(1) Divide VLAN2

2) Ports 2 and 3 are zoned into VLAN2.

3 (1) Enter the router interface 0

2) Configure the IP address of port 0 to be subnet mask.

3) Start this port.

Four1 I'm sorry it's beyond my comprehension, and I forgot all about the loop code 2

Tip: Convert the number of subnets to the mth power of 2. If you want to divide into 8 subnets, 8=2 3, m is 3

After M occupies the m bit of the host address in high order, it is converted to decimal system. For example, if M is 3, 3 bits of the host bit are classified as "network identification numbers", and because the network identification numbers should all be "1", the byte segment corresponding to the host number is "11100000". After converting to decimal to 224, this finalizes the subnet mask.

In the case of a Class B network, the subnet mask is.

**Affordable, no bullying.

After graduating for many years, I was most annoyed with homework.

Did you do this or study this profession? None of this will happen! I advise you to change careers or majors as soon as possible!

To quit smoking, you must first quit psychologically.

Throw away all the lighters and whatever.

Make a plan for yourself.

Let's say 7 days from today.

Never smoke a cigarette yourself.

Stick to it after 7 days.

Hold on for another 7 days.

And so on.

If you're afraid you'll smoke.

Just buy chewing gum and put it on your body.

I can't help but chew gum when I want to.

Cigarettes given to you by others.

Just no, wait until you stick to 10, 100, 7 days, and you will succeed.

By description, it could be an ARP virus.

There are two types of ARP spoofing: one is to spoof the router ARP table, which intercepts gateway data. Notify the router of a series of wrong intranet MAC addresses, and continue to do so according to a certain frequency, so that the real address information cannot be saved in the router through updating, and as a result, all the data of the router can only be sent to the wrong MAC address, resulting in the normal PC cannot receive the information, resulting in disconnection or inability to access the Internet when surfing the Internet; The other is gateway spoofing of the intranet PC, spoofing the MAC address of the gateway, sending ARP packets to deceive other clients, and letting the PC deceived by it send data to the fake gateway, instead of accessing the Internet through the normal router, resulting in disconnection or failure to access the Internet when surfing the Internet.

In response to this situation, Ruixing provides the following solutions:

Method. 1. On the machine that receives the ARP spoofing, in the Start--Run, enter "cmd", enter MS-DOS, and enter the "arp -a" command through the command line window to view the ARP list. You will find that the MAC has been replaced with the MAC that attacked the machine, record the MAC (in case you need to find it), and then find out the computer with the virus based on this MAC.

Method. 2. Use a third-party packet capture tool (such as SNIFFER or AntiARP) to find the IP address that sends the most ARP packets in the LAN, and you can also determine the computer with the virus.

The virus that causes ARP spoofing is actually an ordinary virus, which can be completely solved as long as you determine the source of the starting package and use antivirus software to check it.

1.Make sure your computer is not poisoned first. Antivirus can be updated. Killing... If you can. Try connecting to a wireless computer on another computer...

2.There's a problem with the router... Instability.. Too many connected devices. Check on the route to see if anyone else is rubbing the network... Yes, just use your Mac to filter it out...

3.You use a wired connection to your computer to try... You can know if it's related to the wireless network card.。。。

Hehe: It's not a virus that has to be broken. Because the information provided is incomplete, there are two possibilities:

1.There is a bug in the router, and a virus sends a specific packet that can cause the router to die.

2.Viruses send a lot of junk packets, taking up bandwidth, and the router shields the machine, or it doesn't shield but the router is overwhelmed.

It is recommended that you can kill the virus first and kill the virus. If you confirm whether it is 2, you can install a wireshark to grab a package to see if your computer has a lot of traffic.

If there is this virus, it should be an ARP attack, it is recommended that you vigorously check and kill the laptop, uninstall the Office 2010 you have installed, and see if there are any suspicious processes and boot items.

For more information about the ARP virus, please refer to this.

First of all, you need to verify whether it is a problem with the machine or the network, and check the device. Use your phone on wifi. Look at the speed.

This can only be easily determined, if it is still very slow, you go to the routing settings, see if someone is stealing your network, and set the prohibition condition. If you don't understand, read the manual.

Do you mean that the laptop is an internet café on wifi (i.e. the kind without a network cable), and how long does it take for the router to crash? Don't blindly conclude that it's a virus, right? It could be a problem with your router, or maybe it's a problem with your computer?

Can you provide some clues?

Generally yes or,After entering the IP address in the IE browsing address bar,You can enter the management interface generally with quick settings,After entering,Select the Internet mode,Generally PPPoE mode,The next step is required to enter your broadband username and password,It is Netcom or Telecom for you,Then click to complete the general good,No, you also need to enter the IP address of the domain name server,Different regions are different。 You can look at the IP address of the nearby name server that also uses the route to access the Internet, and you can enter it to get on, and the above instructions require the router to be normal.

:10000

Jinlang's router is the gateway IP of the large router used by our unit

The small route should be.

This setup is either secondary routing or changing the router to wireless AP mode.

This setup does not require an internet ID and password.

Method: 1. Regardless of the Internet access, first connect any one of the routers in your office to ports 1, 2, 3, and 4 with your computer.

At this time, the WAN port is not required to connect to the external network.

2. If you are a TPLink router, please enter the account password admin admin in the IE webpage (For other routers, such as dlink, please enter.)

3. After entering the router settings page, do 3 things:

First, in the wireless network settings, set your SSID, which is the name of the wireless network, such as WangWiFi

Set your office wireless password for example, abcd12345678 to save the settings.

Second, in the menu on the left, it is usually the network configuration that finds the DHCP service, and selects to turn off DHCP. Click Save.

Third, in the intranet settings in the network configuration, change the IP address of the router to be.

Because the main router is so you can't conflict with the main router. Click Save, at which point you will be asked to restart your router.

Start the router and connect the network cable from the computer room to the WAN port, and you can access the Internet at the same time with wired and wireless.

Plug the network cable of one computer in your office into the WAN port of the router, and then take a network cable to connect the computer to the LAN ...... of the routerAny port, and then set it to dynamically obtain IP or static IP on this computer according to the manual, and then set the wireless SSID and password.

When you set up the router, did you enter the Internet ID and password? According to what you said, after linking the wireless router, the computer can't be on, your computer must be linked to the LAN port (one of the 4 ports), the network cable out of the computer room is connected to the WAN port, you try to connect the line in the computer room to the LAN port (one of the 4 ports), if the computer can access the Internet at this time, it should be that you have not set up an Internet account and password!!

The IP of the network cable is not fixed, right? How to enter the web should know, right?