How to flash ZTE mobile phone BA611T

It is not recommended to flash the phone, if there is a problem with the mobile phone system, it is recommended that you restore the mobile phone to factory value or upgrade the system to the latest version, flashing the phone has the following risks:

1. After flashing, the phone may not be able to reach the best working state, and some functions may not work normally. At the same time, because the third-party firmware is not fully tested, there may be problems such as poor compatibility and susceptibility to virus invasion.

2. The flashing machine will bring unforeseen negative effects, please operate with caution. If the device does not work properly and cannot be restored, you do so at your own risk.

3. For software and hardware failures caused by flashing, after-sales maintenance outlets can be treated as non-warranty, and charged according to ordinary out-of-warranty software maintenance.

Telecom new outflow demon card monthly domestic traffic 6GB, free caller ID and 189 mailbox, free domestic answering, ** cost 19 yuan need to log in to the telecom network hall to handle:

2.Open the line brush, switch to the one-click brick rescue interface, and click the "OK" button after completing the "Confirm steps before flashing".

3.If you have a local brushless package, you can enter the model in the search box, click the "Search ROM" button, and click the "One-click Flash" button in the search results to start flashing the package-**After completion, click "Flash Now" to start flashing:

4.If there is already a flash package locally, click the "Select Local ROM" button to open the interface for selecting a RAM package, and click the "Open" button after selecting the flash package

5.Enter the parsing package page

6.After the unpacking is complete, start scanning the flashing port:

7.Install the flashing driver:

If it is the first time to start the line brush, or you have not installed the flash driver, please click "Fully automatic installation of the flash driver":

Enter the installation driver interface, if the Windows security prompt pops up, click "Always install this driver software":

8.After installing the driver, if the port cannot be scanned for a long time, you can manually enter the flash mode according to the interface operation guide

10.Jump to the flashing success interface, and the flashing is complete!

The steps are as follows:

ZTE BA601 Brush Machine Brick Rescue Tutorial Details:

One: Preparations for line brush brick rescue:

2: Precautions before flashing:

1: Confirm that your mobile phone can be connected to the computer with a data cable, which is necessary and the basis of operation;

3: Please make sure that the battery of the mobile phone is more than half of the battery before flashing, this is very important;

4: In the process of system upgrade, do not operate or press which key to press;

5: Do not deduct the battery during the flashing process;

6: Ordinary data cable can also be flashed, provided that your data cable transmission is stable;

7: Back up your personal address book and other information before swiping;

Three: Flashing steps using the MT** brush tool.

5.When the red scroll bar appears, the connection is successful, and when the yellow bar starts to go, release your hand.

6.When the yellow scroll bar starts to go, and when it reaches 100, the upgrade is completed, wait patiently during the upgrade process, and do not move the line halfway (to prevent the socket beam from talking about poor contact).

7.After the check mark (check) appears, unplug the data cable, replug the battery, and turn on the device. The first time you turn on the phone, you need to update the system, wait patiently for 3 to 5 minutes, and do not move the phone halfway to prevent power failure. (may reboot multiple times).

8.After the phone is turned on, when there is no problem in testing all functions, turn it off and restart it, and then use it normally.

As long as you follow the above correctly, you will be able to flash the driver correctly.

Summary. ZTE ZTEBA601 how to get on the card.

Hello dear,,Open the back cover of the phone to see the card slot。

If my answer is helpful to you, please give a thumbs up (in the lower left corner), I look forward to your like, your efforts are very important to me, and your support is also the motivation for my progress. Finally, I wish you good health and a good mood!

ZTE ZTEBA601 how to get on the card.

ZTE zteba601How to get on the card, hello dear,,Open the back cover of the mobile phone to see the card slot, I hope it can help you。 If my answer is helpful to you, please give a thumbs up (in the lower left corner), I look forward to your like, your efforts are very important to me, and your support is also the motivation for my progress. Finally, I wish you good health and a good mood!

I can't read the card when I put it up.

ZTE zteba601I can't read the card on it, 1. Check whether the SD card slot is intact after shutting down. 2. If it doesn't work, then use another SD card to try, or use a card reader to identify whether the SD card is in good condition on the computer. 3. If it still doesn't work, back up the mobile phone and use the function of restoring the factory settings of the mobile phone.

When powered on:

Go to [Settings] - [Backup & Reset] - [Factory Reset], and then follow the on-screen prompts, the whole operation process will take about 3 minutes, and the system will automatically restart after completion.

Note: 1The first boot time after resetting the factory settings will be longer, please be patient.

2.To restore factory settings, you can check [Format phone storage], this option will erase all data in the phone settings and phone storage, including **, **, etc., please back up user data in advance.

Powered off:

1. Press and hold [Volume Up], [Home Button], and [Power Button] at the same time in the shutdown state, and wait for the screen to light up before you can release it and enter Recovery mode.

2. After entering the recovery mode, the English selection interface will appear, select wipe data reset to confirm - and then select the middle line yes--delete; Are you sure.

3. Re-election. Take wipe cache partition to confirm it once.

4. Finally, select the first item, Reboot System No W, and restart the phone.

Note: When performing the above operations, be sure to back up your phone's personal information, books, text messages and other important data, because these data will be erased when unlocked.

Reference path: Go to [Settings] - [Backup & Reset] - [Factory Reset], and then follow the on-screen prompts, the whole operation process will take about 3 minutes, and the system will automatically restart after completion. Note:

1.The first boot time after factory reset will be longer, please wait patiently. 2.

To restore factory settings, you can check [Format phone storage], this option will erase all data in the phone settings and phone storage, including **, **, etc., please back up the user's data in advance.

Here's how:

Second, then copy to the root directory of the memory card of the mobile phone, if you use a data cable to connect to the computer, you can directly put it into the root directory of the memory card of the mobile phone through the data cable.

3. When the phone is powered off, keep pressing and holding the volume up button and then press the on button to select Recovery mode. Press the volume down button again to confirm to enter recovery mode.

5. Then select File in the list that appears, and then press the power button to confirm, and then start flashing.

6. It will take about 2-3 minutes for the phone to start the upgrade (during this upgrade process, please keep the phone flat and do not touch the screen).

7. After the upgrade is completed, select the "Reboot System Now" option and press the ON key to confirm. The phone will automatically restart, and the phone can be used after normal boot, so far the upgrade is complete.

PS: Remember to back up your important files and data before flashing to avoid losing them after flashing.

Flash the sub-card and brush the line,If the novice doesn't know how to operate,Try to watch the tutorial carefully after flashing,The flashing package can be found in the ROM channel,Here is a relatively rich Android phone flashing package。