It is necessary to operate the whole car film operation process and the car film process

The construction process of film is simple, which can be roughly divided into: film cutting - glass cleaning - baking and shaping - formal film - environmental cleaning.

1. Film-cutting: Measure the car glass to be constructed, accurately measure the size of the window, and cut the accurate window shape according to the measured size.

2. Clean the glass

When cleaning the glass, spray water on the outer glass and wipe it with your hands, because the sensitivity of the human hand is the strongest, and you can feel the slightly larger dust particles.

3. Baking and shaping:

For the front and rear windshields of the car and the side glass with a large arc, the film is baked and shaped with a high-temperature electric heating gun to be completely consistent with the curvature of the glass.

4. Formal film:

When it comes to the formal filming, most of the upper film will be pasted from top to bottom, starting from the top of the glass to tear off the upper part of the film, and the protective film will be slowly scraped downward, and the protective film will be moved down while scraping to the bottom of the glass.

5. Clean environment:

Finally, it is necessary to clean the environment after the film is applied. Wash the film that has been pasted, and then remove the water impermeability protective cover. Return the original items in the car to their places, and clean up the construction waste and stagnant water outside the car.

It should be noted that professional film tools must be used in the entire film construction process, and the general standard construction shops have professional film tools.

Car Foil Steps (for Windows & Windshield): 1First of all, you need to measure the size of the glass and cut it according to the size.

It's okay to be a little bigger, but it must not be smaller, because it will shrink a little after the hot air is blown. 2.Then use a special car wash liquid to clean the car glass, especially the obvious stains, be sure to clean it.

In addition, residual water needs to be removed after cleaning. 3.Then you can apply the film, heat the car film (hot air blower), spray a layer of glue (mainly water) on the effective film surface, and then smooth the film a little from top to bottom.

If the size is still large at this point, the additional film will have to be cut. 4.If air bubbles are found after pasting, they must be scraped off with a soft scraper.

It doesn't matter if the bubble doesn't blow off. The sun will disappear in a few days.

You can go to the Naesso thermal insulation explosion-proof film franchise store to understand, they have on-site demonstrations, very professional.

Car film process, first of all, car film preparation work, cleaning and interior protection. In order to prevent the production of tiny impurities during the film, the car is usually cleaned all over the body when the car film is applied, and the car interior must be protected before the car film, especially for new cars, because it will inevitably stain the car interior during the film process, so it is necessary to prepare for the work in the early stage.

Secondly, the car film is tailored according to the size of the window. Film cutting is an important process of car film, the size of car film is generally determined according to the specific size of the window, with a size slightly larger than the size of the window.

After that, the front and rear windshields are cleaned and other window glasses. In addition to the whole vehicle cleaning, also need to carefully clean the window glass again, at the time of cleaning, generally with two kinds of scrapers (hard scraper and soft scraper) to the car repeatedly scraped. Now the car film will be operated in the dust-free workshop, which is also to prevent impurities in the car film and affect the effect of the film.

Finally, there is the film, baking film, and wet film. When cutting the film, the staff will spray soapy water on the car window glass, so that in order to better paste the car film, after the adhesive layer of the car film is uncovered, it should be carefully glued to the inside of the car window, and the edge distance between the car film and the car window should be adjusted under the lubrication of soapy water to ensure the overall appearance.

Photo by Li Linwei) @2019

Hello, dear. The process of car film is divided into several stages: cleaning car glass, cutting car film, car film shaping, car film pasting, and quality inspection, and the following are the specific process methods: 1. Clean car glass.

This is the first and most important step in the car film, and whether the glass is clean or not directly affects the subsequent film work. Therefore, it is necessary to first wash the glass and the edges of the glass with water that has a cleaning effect but does not include chemicals, and then wash repeatedly to ensure that they are clean. Then use a scraper to scrape the glass from the dry side to the wet side, from top to bottom, and wipe the edges with a cloth.

2. Cutting the car film. Tailor the film to the actual size of the glass. Prepare the glass sample of the model in advance, and cut the car film according to the model.

3. The car film is shaped. After the film is cut, it is covered on the outside of the glass, heated with a heat gun on the part that needs to be shaped, and at the same time, the car film is tightly attached to the glass with a scraper. 4. Paste the car film.

After the car film is set, stick it on the inside of the glass, tear off the car film liner, when the liner is completely removed, stick the film on the glass, and adjust the length of the left and right sides so as not to touch the car frame. Spray water onto the back of the membrane, scrape water from top to bottom, center to edge, and dry with a towel. 5. Quality inspection.

Check whether it is firmly pasted and whether there are air bubbles between the car film and the glass, etc.

Summary. Pro, the method of car film operation is to wash the car, measure the size, apply the film, set the shape, and check whether there are bubbles. Car Wash:

Before giving the car film, you need to wash the glass, because if the car glass is not cleaned, the car film will be blurred, which will not only affect the appearance, but also affect the quality of the car film, cleaning the glass is very simple, wash with water, and then wipe it repeatedly with a dry rag, in order to be able to wash it clean, it is best to wash it several times.

Pro, the method of car film operation is to wash the car, measure the size, apply the film, set the shape, and check whether there are bubbles. Car washing: Before giving the car film, you need to wash the glass, because if the car glass is not cleaned, the car film will be blurred, which will not only affect the appearance, but also affect the quality of the car film, cleaning the glass is very simple, clean it with water, and then wipe it repeatedly with a dry rag silver, in order to wash it clean, it is best to wash it several times.

The main process of car film.

Pro, the main process of car film is car washing, measuring the dust inch, filming, shaping, and checking whether there are bubbles. Car washing: Before giving the car film, you need to wash the glass, because if the car glass is not cleaned, the car film will be blurred, which will not only affect the appearance, but also affect the quality of the car film.

Measurement: according to the size of the window to cut the car film, cutting film is an important process of car film, the size of the car film is generally determined by the specific size of the window, the size of the cut is slightly larger than the size of the window. Wrap:

The film is cut to the appropriate size and covered on the outside of the glass, and the film is shaped with a scraper blade. Stereotype: When cutting the film, the staff sprays soapy water on the window glass of the car, which is to better paste the car film, and uncover the paste layer of the car film after shaping, the car film must be carefully pasted inside the window, and the distance between the film and the edge of the window is adjusted under the lubrication of soapy water, in order to ensure the overall appearance.

Check whether there are air bubbles: After completing the above steps, carry out the final inspection, such as whether there are air bubbles, etc., if there is no problem after the inspection, then the car film is pasted.

<> "Car film is a difficult technical work, and the process of film will also affect the final effect; Some car owners have strong hands-on ability, and complete tools will choose their own film. So what is the car film process and precautions?

First of all, before applying the car film, the glass needs to be cleaned, because if the car glass is not cleaned, it will become blurry after the car film is pasted, which will not only affect the appearance, but also affect the quality of the film.

Secondly, prepare the glass sample, measure the size, and then cut the car film to the right size.

Then, cover the outside of the glass with the car film cut to the appropriate size and wide core, and use a scraper to carefully attach the car film to the stove to set the shape.

Next, remove the liner after styling, and then attach the film to the inside of the glass. After pasting, spray water on the back of the car film, and then use a scraper to scrape out the water.

Finally, after completing the above steps, carry out a final inspection, such as to see if there are air bubbles, etc., if there is no problem after the inspection, then the car film is considered to be pasted.