Questions about wireless routing and wireless network cards!!

1, you need to buy a 150m wireless router, the brand of Mercury is not bad, buy a brand of network card and router, the compatibility will be a little better.

3. As long as the wireless signal strength is enough, your wireless network card can also reach this speed.

1.At least it doesn't make a difference if you use it!

3.Mercury's is still good and cost-effective.

There are many routes on the market, just buy one! The network can definitely cover your home!

150M refers to the transmission rate of the wireless network card, which is far greater than your network speed, and your ** speed depends on your network speed rather than the speed of the network card. Mercury's has not been used, and I have the impression that it is **cheap. An ordinary router is enough in such a small space as a house.

Mercury is a low-end brand of network manufacturers, if you want a better route, you can learn about dlink, my family uses this brand, not bad. Normally, 150m is fine, but 150m and 300m are 11n technology, and it seems to be transmission power. **Speed is related to your home's broadband.

First of all, what I'm not sure about is that the cat you're talking about is wireless, so does the cat have a routing function? Are you going to use two computers to share the Internet at the same time, or do you take turns using this cat to get on it?

If it is the former to share the Internet, first of all, you must set up the cat, you must set the cat to a comprehensive mode (that is, a route that can be automatically dialed), enter the Luxu password for Internet access in the settings, and turn on the wireless signal by the way for the laptop to receive. Since your cat is now connected to the desktop, everything has to be done through the desktop.

After this setting, there is no need to set up any local connection, and both computers are directly connected to the Internet without dialing, so the network configuration of the notebook is impossible to talk about, and the IP can be obtained directly and automatically.

If the notebook is set up in this way and still can't receive the wireless signal, you have to check whether the notebook is turned on the wireless network card, there is usually an indicator to show whether the notebook has received the wireless signal, if not, you have to turn it on through the shortcut key or the corresponding open sail burn off.

Does your desktop also come with wireless?

If you want to add a wireless router at the same time, it is about 100 yuan.

For laptops, there is a setting to turn on the wireless network card first.

Did you add a voice splitter? If you add it, enter the router management interface and set it up according to the manual.

Don't listen to the nonsense upstairs, you can connect the router, whether wired or wireless.

Connection: The landlord's network cable is connected to the WAN port of the router, and other computers are connected to the LAN port.

The main one is the router IP settings:

1. If the landlord's router number segment is or.

Then, regardless of whether he has DHCP turned on or not, as long as your MAC address and IP are not locked (which is not something that non-professionals can handle), your router's WAN port settings can usually be set to 100-200 addresses in the same segment, such as:

Or because, the general router has DHCP turned on, and the default number range is 100-200, so you can arbitrarily take the value in the range;

However, it is best to stay away from 100 (in the case of automatic allocation, it is usually allocated upwards from 100) to avoid conflicts with other user IPs.

2. Here comes the main problem

The IP address of your router's LAN port must be different from the landlord's IP address so that there is no conflict.

That is, the third digit value must not be the same, it is very simple, take any value of 0-255, it is recommended to use 10 or 20, it is easier to remember. Such as:

or 192, which is the gateway address of the computer you connect to on your own router, so it can't be the same as the landlord router.

Then turn on your DHCP and let the computer automatically connect to your router and get the address automatically.

3. If you use wireless connection, it is recommended that you change the router administrator name and password, and set the connection password. Be responsible, others can rub your network, and you can also enter the route at will to limit your network speed, haha, that miserable ......! I don't know what's going on yet.

For specific settings, we recommend that you read the router manual carefully.

Hope it helps.

Yes, but you have to turn off the DHCP function and firewall of your wireless router, and assign an IP that is different from the current line segment, and then connect the network cable to the LAN port, not the WAN port, and use the wireless router as a switch.

It depends on what the landlord has set up.

If not, you can directly connect the cable that the landlord has given you to the wireless router, and then set the wireless router according to whether the IP of your computer is automatically obtained or manually set, and remember to set the password. Then use your laptop and use the wireless connection to surf the Internet...

Is the IP of the cable you pulled over static or dynamic? I estimate that the dynamic is the majority, then you should pay attention when you go to buy a wireless router, be sure to confirm that "the external network port supports dynamic wireless routing", when you buy it with the boss, say this, about 100 yuan, will not exceed 120 yuan, it is very easy to get, there is a lot of information on the Internet, and the wireless router also comes with an instruction manual.