How can you go wireless if you have already converted through a wired router?

There is a line connected to the wireless route by the B port, the wireless router is placed in your home, and the line is connected by dial-up.

Cat - Wired by - Wireless Routing - Computer.

Setting method: In the wireless router WAN setting, change the Internet access mode to dynamic IP

In the LAN settings, change the IP and DHCP of the route, and if there is a line that is used by the IP segment, the wireless route can be changed.

There are two ways to do this.

1. It is better to use wireless routing is to put the wireless routing in your home is more convenient, wireless routing is generally network cable port access, you can use your original route to bridge the use of it (you can put the original routing and wireless are put on your home, isn't there a network cable, the line as an ADSL signal access to your home, the rest of the unchanged can't Finally, under the setting, wireless access does not need to set a password, bind the MAC address on it).

2. Just connect the network cable you plug into the computer to a wireless AP (that is, a "wireless switch").

Hope it helps, don't understand email.

Yes, buy a router with wireless function, wireless +4 port, about 200 yuan.

Wired without password Wireless can be set with a password.

Set up a router so that it can access the Internet, then connect to B router, turn off the DHCP of B router and change the LAN port IP address to as long as it is in the same network segment as A and the LAN port IP address is not the same), set the IP of the computer and then enter the B router, turn on its wireless function and set the wireless password, fill in the LAN port MAC address of router A into the wireless AP of B, turn on the wireless in the same A and set the password, note that the password of A and B is set to the same, The encryption type and SSID should be the same, fill in the MAC address of the LAN port of router B into the AP of router A, connect to the computer in B after setting, and use the ping command to see if the LAN port address of router A can be pinged, if it can prove that the wireless bridging is successful.

Two wireless routers are connected.

2. Set up a WAN port to access the Internet.

3. Set wireless parameters. Enable the bridge function, where the MAC address is the MAC address of another 641G wireless router. In the same phase, the MAC address indicating 340G is also added to the same position of another 641G.

Note: The MAC address of the LAN port is obtained, which can be queried in the host status in the wireless parameters); The frequency band should be consistent with another route, and the recommended segment; Enable SSID broadcasting.

4. Password setting. If enabled, the security type, key format, and password must be the same.

5. Shut down the DHCP server.

8. Computer. Connect to 640G (that is, the account of the second router unit). The gateway is used (to write the LAN port IP address of the 340G route). The LAN port of the bridged 641G can be connected to a network cable with other computers.

There are two connection methods, which are wired and wireless.

Wireless bridging is to connect two wireless routers wirelessly; After the wireless bridging of the two wireless routers is successful, the wireless wifi name can be unified to achieve wireless roaming.

In addition, we can also use a network cable to connect two wireless routers, and there are two ways to connect the two routers with a network cable: set up a secondary router and set up a wireless AP (switch).

Wireless bridging is two wireless routers that are connected wirelessly without the use of network cables. Therefore, it is more convenient and flexible in deployment, and gets rid of the trouble of pulling network cables; In addition, after wireless bridging, the wifi name and wifi password on the two wireless routers can be set to be exactly the same, that is, wireless roaming can be realized after wireless bridging.

However, it is also because of wireless bridging that two routers are connected wirelessly; So, in terms of network stability, transmission speed, etc. Compared with the way of connecting two routers with wires, there is a certain gap.

The way to connect two routers with network cables has great advantages over wireless bridging in terms of network stability and transmission speed. Moreover, the distance between the two wireless routers cannot be compared with the wireless bridging method.

The disadvantage is that you need to deploy network cables, which is very troublesome; And if the distance between the two routers is tens of meters, you need to spend dozens of dollars more to buy a network cable. In addition, after connecting the two routers with network cables, the wifi signal on the two routers cannot achieve wireless roaming; That is, the wifi name and password on both routers cannot be the same.

Very simple. The broadband dialer connects to the WAN port of Router 1, and the LAN port of Router 1 connects to the WAN port of Router 2. Set the dial-up and password in Router 1, and set the LAN IP segment to . Router 2 is set to fixed, gateway is set to , and LAN IP segment is set to .

Buy a wireless router with AP function and follow the instructions.

It depends on whether you need to use the router or the switch of the transfer.

Wireless router, or wireless AP.

Set up, plug the network cable into the WAN port of the wireless router, and then go to the settings page and select dynamic IP access. Save, restart.

If you want to buy a wireless router, just follow the instructions when you come back!

Broadband connection to wireless router conversion method: Set up router dialing.

Home Network Environment Cabling]:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser - enter the general router address is this or check the login information on the back of the router) into the route - enter the user name, password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter the Internet user name and password according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.