What does DuPont servo drive alarm ER03 mean

Summary. Servo drive repair failure** Hello dear,!"Position deviation is too large fault 1, UVW wiring of servo motor; 2. The gain of the servo drive is low; 3. The frequency of the position command pulse is high; 4. The acceleration of the position command is too large; 5. The position deviation exceeds the position deviation is too large, and the value set by the fault value is too small; 6. Servo drive motor fault 1. Confirm the wiring of the main circuit cable of the motor and re-wire; 2. Confirm whether the gain of the servo drive is too low and increase the gain; 3. Try to reduce the command frequency before running to reduce the position command frequency, command acceleration or adjust the electronic gear ratio; 4. Reduce the acceleration of the command before running, and add smoothing functions such as position command acceleration and deceleration time parameters; 5. Confirm whether the position deviation fault value is appropriate and set the value correctly.

<> servo drive repair failure**.

Servo drive repair failure** Hello dear,!<

"Position deviation is too large fault 1, UVW wiring of servo motor; 2. The gain of the servo drive is low; 3. The frequency of the position command pulse is high; 4. The acceleration of the position command is too large; 5. The position deviation exceeds the position deviation is too large, and the value set by the fault value is too small; 6. Servo drive motor fault 1. Confirm the wiring of the main circuit cable of the motor and re-wire; 2. Confirm whether the gain of the servo drive is too low and increase the gain; 3. Try to reduce the command frequency before running to reduce the position command frequency, command acceleration or adjust the electronic gear ratio; 4. Reduce the acceleration of the command before running, add the position command, acceleration and deceleration time, and the smoothing function such as the number of ants to calm the pure; 5. Confirm whether the position deviation fault value is appropriate and set the value correctly. I hope I can help you! <>

<> servo drive repair failure**.

Servo drive repair failure** Hello dear,!<

Communication between the encoder and the driver is interrupted and communication interruption detection is activated. Follow the wiring diagram to connect the encoder line correctly. Correct incorrect wiring.

What is the reason for the alarm of the servo drive ERR047? How to solve the alarm of servo drive ERR047? The properties of the err object are set by the wrong producer (Visual Basic, object, or programmer).

When a runtime error occurs, the properties of the ERR object are populated with information that uniquely identifies the error and information that can be used to handle the error tolerance. What is the reason for the alarm of the servo drive ERR047? How to solve the servo drive Ant Commander err047 alarm?

The electronic scale shows that there is no signal, the reason is that the weighing display is poorly wired, the signal line is disconnected, and the second reason is that the load cell is damaged. Electronic balance is one of the scales.

HCFA servo drive alarm**ERR047 is to indicate servo emergency stop. The cause of this failure is that the 24V power supply in the control loop is not connected. Hope it helps!

Dear, for you to find out the servo drive ER03 alarm reason: 1The controller does not match the phase of the motor.

2.The main circuit R, S, T is undervoltaged, please check whether R, S, T has a voltage of 220V, if the voltage is lower than 180V, the driver alarm. 3.

The control circuit r, t is powered first, and the main circuit r, s, t is also powered, and the main circuit of the servo drive must be powered before the control circuit. Solution situation 1: When the main circuit is turned on:

Circuit board failure, power supply fuse damage, soft start circuit failure, rectifier failure, low power supply voltage, temporary power failure for more than 20ms. Situation 2: During the operation of the motor, the power supply capacity is not enough and the power is lost instantly.

The load of the X-axis servo motor is too high, it may be that the X-direction lead screw bearing is broken, or it may be that the lead screw is broken and the motor cannot be moved. The likelihood of a system problem is slim and it is recommended to report for repair.