How does the dump truck compartment lift and land? Which buttons do you press? 5

The vehicle is flat and not tilted, hangingNeutral, step on the clutch, turn on the tipping switch, pull the force take-off, release the clutch and start the bucket. When starting the bucket, you should pay attention to whether the rear door opens automatically, and if it is not open, turn off the tipping switch. Get out of the car and use a stick or hammer to open the back door, and then continue to jack up, unloading half of the car and walking a little forward, so that the goods on the car can be completely unloaded.

Although there are many types of vehicles, the structure is similar. This should be said to be the credit of standardization, but also the need for large-scale production lines. With the development of society, the progress of science and technology and the change of demand, the shape of railway vehicles has begun to change, especially the passenger car is no longer the same old face.

However, their basic structure has not changed significantly, but the specific parts have a more scientific and advanced structural design.

Generally speaking, the basic structure of the vehicle is composed of five parts: the car body, the undercarriage, the running part, the coupler buffer device and the braking device.

The body is the part of the vehicle that is used to load goods or passengers, and is the basis for the installation and connection of other components of the vehicle. The body of the early vehicles was mainly made of wood, supplemented by steel plates, bow rods, etc. In modern times, the car body is mainly steel structure or light metal structure.

Generally, there is a button called the replacement device in the cab, which controls the battery valve, connects the compressed air control transmission, that is, the hydraulic pump. Press and hold the clutch pedal while the vehicle is parked, press this button and slowly release the clutch. In the operation of the landing dumper.

I don't know if I'm clear enough.

Generally, in neutral gear, press the power take-off switch, step on the clutch, hang the third or fourth gear, and then dial the lifting gear of the lifting switch, slowly loosen the clutch, and lift the trunk; After the goods are reversed, dial the neutral gear, turn off the power take-off switch, hang a gear and walk slowly for a short time to dial the lifting switch to the lower gear (there are slow and fast points) until the cargo box is completely lowered and then release the clutch and leave. If it is more difficult to pour the mud, you must do two or three times down, but also depends on whether the car is parked in a horizontal position, if it is not flat, it is best not to fall, it will hit the bird or roll over, be careful.

How to unload a blue dump truck.

Give me points, I'll send you a private message!

It depends on what kind of car you drive, it's hard to say, not every car operates the same.

1.There is a high probability that the cylinder bracket is not in the center. 2.This can also happen if the frame is deformed or if the fulcrum of the rear reversal bracket is asymmetrical.

In general, there is a smaller handle near the front of the car, which is a safety bolt. You need to pull it first and then press the big handle to stand up.

But different types of trucks have different ways of operating.

1. Truck is a commercial vehicle designed and equipped for the main purpose of carrying goods. It can't tow a trailer.

2. Large trucks.

It is used to transport bulky goods, such as large machine tools, generators and turbine rotors, rolling equipment, transformers, chemical synthesis towers and complete sets of equipment, etc., its carrying capacity is larger than that of ordinary flat cars, and its own weight is also larger, so there are more axles that can adapt to the allowable axle load of the line.

and per linear meter. The limit value of the load. The offset generated by the curve when the vehicle is long.

Larger, due to the limitation of the vehicle limit, the maximum width of the middle of the vehicle needs to be reduced.

3. When some vehicles pass through the curve, they also need to be equipped with a special mechanism to move to the outside of the curve, so as to ensure that the goods installed in the middle of the vehicle and the center line of the movable vehicle underframe are close to the center line of the curve, so that the center part of the goods and the vehicle underframe does not exceed the vehicle limit size or the maximum limit size specified for the oversized goods.

4. According to its structure, the long car can be divided into: long-term flat car, concave bottom flat car, hole car, clamp car, etc.

The dump truck compartment falls on its own after being lifted for the following reasons:

1.Check valve stuck;

2.Poor sealing of the sealing ring of the lifting cylinder;

3.The distribution valve is stuck and not fully in place;

4.There is a leak in the pipeline.