Software to capture clips from RMVB videos

Method: Import first, select the format you want to convert, if you don't want to change, choose rmvb, choose the resolution (that is, the screen size you want after conversion), and then set the file output path, the most important thing is to choose the position of the starting and ending points of the ** to be intercepted and then convert it.

<><4. Then move the two pushers, and the part between the two pushers is to be intercepted, click Next. If you want to take an accurate cut, enter the start and time points of the rock beam in the Start and End Time column.

5. Wait for the processing to be completed, and then click "Open Output Folder" to find the intercepted clip. After completing the above settings, you can use the expert software to capture the clip.

<>1. Add files.

2. Select a clip.

After adding **Quick** to the merger and splitting software, after clicking [Add Segment], we can see that there is a progress bar below the **Clip that can be selected**, and the **fragment can be selected by pulling the bridge leakage progress bar, if the same ** needs to cut multiple clips, click [Add Segment] again. Finally, click Start to export the cuts.

<>1. Add files.

2. Add special effects.

Click the [+] between ** and a transition effect will appear. You can also set parameters such as the duration of the transition and the direction of the transition. Don't forget to click the "Confirm button" when you're done.

3. Start exporting.

Is there any software that can intercept **fragments, + This 321524, the update is also very fast, first, press F8 when starting up, enter the safe mode interface. But when you go in, if you wait for a few minutes and there is no response, it keeps saying that please wait for a while to reset the key to restart the computer, such as the one-click ghost backup installed before the gear slider computer, you can decisively restore it and try it, but if it is still the case after the restoration.

Second, the computer boot or in the boot windows interface stuck, so long into the PE system set up again, reboot press the delete key, enter the boot interface, set the boot to U disk start, enter the PE system, three, in the PE system with the newly prepared Windows7 reinstallation, installation and restart.

Fourth, if the computer is still stuck in the boot windows interface, then clean the inside of the chassis dust.

5. First of all, press F8 when booting up to enter the safe mode interface. But when you go in, if you wait for a few minutes and there is no response, it keeps saying that please wait for a while to reset the reset button to restart the computer, if the computer is installed with a one-click ghost backup before, you can decisively restore it and try it, but if it is still the case after the restoration.

Sixth, the computer boot is still in the boot windows interface stuck, so long into the PE system set again, restart press the delete key, enter the boot interface, set the boot to the U disk start, enter the PE system, seven, in the PE system with the newly prepared windows7 reinstallation, installation and restart.

8. If the computer is still stuck in the Windows interface, then clean up the dust inside the case.

9. First of all, press F8 when turning on the computer to enter the safe mode interface. But when you go in, if you wait for a few minutes and there is no response, it keeps saying that please wait for a while to reset the reset button to restart the computer, if the computer is installed with a one-click ghost backup before, you can decisively restore it and try it, but if it is still the case after the restoration.

10. If the computer is still stuck in the boot windows interface, enter the PE system again for a long time, restart and press the delete key, enter the BOOT interface, set the boot to U disk start, enter the PE system, ten.

1. Reinstall Windows 7 in the PE system with the newly prepared Windows7, and install and restart.

Ten. 2. If the computer is still stuck in the boot Windows interface, then clean up the dust inside the case.

<>1. Add files.

2. Select a clip.

<>1. Add files.

2. Add special effects.

3. Start exporting.

OCAM is the easiest option, and it is the smallest free screen recording software in the test.

1. mkvtoolnix

For example, if you want to cut out clips from minute 5 to minute 10, select "Cut into segments according to timecode", and then enter "00:05:00-00:" in the segment

10:00", the file name here in the output file name, and then start mixing the stream.

Second, the format factory.

Use Format Factory, this software is very useful and is used in many places.

A lot of mainstream software does.

<> "Set the output directory, generally save the default original directory.

<> you can also pull the progress bar and click "Capture to List" to crop.

After <> click, we return to the previous interface, click on the lower right corner to crop all.

<>1. Add files.

2. Select a clip.

After adding **to the quick** merging and splitting software, after clicking [Add Segment], we can see that there is a progress bar below **Clip that can be selected**, and you can select the cut **fragment by pulling the progress bar, if you need to cut multiple clips of the same **, click [Add Segment] again. Finally, click Start to export the cuts.

<>1. Add files.

2. Add special effects.

Click the [+] between ** and a transition effect will appear. You can also set parameters such as the duration of the transition and the direction of the transition. Don't forget to click the "Confirm button" when you're done.

3. Start exporting.

It is the easiest choice, and it is the smallest free screen recording software in the test;

**File is one of the files we often encounter in our daily life, recently the small ** has been more popular, so when we ** to some **files on the computer, what software can be used to intercept** fragments?

3. After the file is opened, click "Split" to set "Start Time" and "End Time".