Network issues Does the router need to be set up?

There is no need to set up, but the incoming cable Please plug in any port of 1234, do not plug in the normal port, because your network environment is LAN!

Yes, you can use TPLINK, plug and use, automatic adjustment, very convenient.

The wizard does not need network support, but you must use a network account when setting up, generally speaking, the router setup interface is the username admin password is also.

Change it in Network Parameters --- WAN Port Parameters.

The router can be set in the state of no network and no network, but after successful setting, it needs to be installed in the broadband line to use the network normally, the following describes the steps to install and set the router (take the fast router as an example):

2. Then open the browser of the computer, enter the login address and login password of the router, and the specific login IP and password can be looked at the label on the back of the router.

3. After entering the router, there will be a setup wizard, first fill in your broadband account and password.

4. Then set the wireless name and connection password.

5. After the successful setting, a prompt will appear for the successful setting, and it will take effect by restarting the router.

Connect your router to your computer. It is usually connected by a network cable.

If you don't need it, you can set it up by logging in to the link route.

Most routers need to be connected to the computer with a network cable before logging in to the router to set it up. Because some routers are in their original state, the wireless function is turned off.

This is generally set up like this:

Connect the incoming cable to the "wan" of the router, and then use the desktop to connect to the "lan" of the router through the network cable, enter it in the browser address bar, log in to the router, enter the user name admin, password admin, and enter the settings:

1. Internet access method (PPPoe dial-up).

2. Internet account and password, 3. Use "MAC address copy". Pay special attention to this! 4. In the LAN settings, you can enable automatic IP address assignment (DHCP) by default.

5. Enable wireless AP. Encrypt if necessary.

Save to exit.

You don't need to be connected to the Internet, as long as the router is set up correctly.

Generally there is a manual wow.

No, you install it, look for the router settings, and a large piece of it comes out.

Definitely, you don't have a network, why do you want a router?

The mobile phone and laptop can be connected, which means that the internal settings have been successfully set. You now need to set up the broadband external line.

1. Use a computer to directly connect the ADSL cat (** line) or PON cat LAN port (optical fiber FTTH) to see if you can access the Internet. Determine if the outside line is normal.

2. Your image is a tpliink router, and it has several dial-up modes that you can try to change. TPLink has some special firmware that needs to be upgraded for special areas.

3. If you are a cell broadband provider, there are individual cell broadband providers that prohibit connecting to routers.

The WLAN port is not resolved, you are using the DHCP protocol to automatically obtain the IP address, you want to use the wireless network through the wireless router so that the mobile phone can also access the Internet, so you can't use the method with an account and password to set up the wireless router, this is definitely not possible, your WLAN port has not been parsed to, and you need to change to a different network segment and the previous dynamic IP address if you want to parse.

You can see what the system log in the system settings is caused by.,It may also be a binding problem.,This has to call ** to customer service and ask customer service to kick you offline.,You can consider restarting the cat before doing this.。 Note: Call ** to customer service and ask them to kick you offline, to ensure that the cat can be synchronized normally.

After the cat is synchronized, the state is optical cat: network G or E is always on, and ordinary cat: network L light or Intel light is always on).

Reset the router and give it a try; If you are using that kind of monthly network card, see if it has expired; There may be a problem with the routing, or there may be a problem with the account that is surfing the Internet.

The router is not connected, the account settings are not right, or call the operator directly.

The routing dial-up is not connected, it is recommended to look at the pppoe account settings, and there is a test when setting up.

Did you dial-up Internet access on the computer before?

You can also set up a router without a network, and the setup method is as follows;

1.The router is connected with a network cable.

Connect the router port to the computer with a network cable as shown in the figure below, and change the computer IP address to be in the same network segment as the router's IP address, so that you can set it when you log in to the router, for example, the router IP address is the reference to the identification on the back of the router), and the IP address of the computer can be set.

2.Log in to the router wirelessly.

Turn on the power of the wireless router, the wireless router will establish a wifi connection by default, connect to this wifi hotspot with a laptop or mobile phone, the computer will automatically obtain the IP address, and then you can log in to the IP address of the router in IE, such as referring to the logo on the back of the router), enter the user name and password to enter the settings.

Note: If you set up the router for the first time, you will not be able to log in with a wireless connection because the router does not establish a wifi hotspot by default, and you can only use the wired connection mode.

You don't need an internet connection to set up your router!

Set up router dialing:

Automatic acquisition of computer IP and DNS settings;

1. Enter the router. In the [Setup Wizard], select [PPOE Dialing] (some are ADSL Dialing), enter your Internet username and password as prompted, and save;

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPOE Dialing] in the three options of [Connection]. The next is to select [Auto Connect], Save, and Exit;

3. If you want to use wireless wifi, your router must have a wireless routing function, in the settings, turn on the wireless routing function, here, the wireless signal signal is changed to one of them. The strongest anti-interference.

You can also set a password for your Wi-Fi connection.

Do not wire the WAN port of the router, connect the LAN port of the router to the computer with a network cable, and enter the router setting page according to the steps in the manual: enter the account and password of the broadband, select the PPPoE dial-up method, select the IP and DNS options provided by the ISP, turn on the wireless signal, turn on DHCP, and set the computer to "automatically obtain IP address" and "automatically obtain DNS server address" to confirm.