How to repair the watch when water enters 5, how to repair the watch when water enters the watch

If you find that the watch is flooded, you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, put it about 15 cm near a 40-watt light bulb, and bake for about 40 minutes, and the water vapor in the watch can be eliminated. Do not bake the watch directly near the heat, so as not to deform the glass by heating. Because although there is no moisture on the dial, there may still be water in the movement, and the movement will rust and cause damage to the movement after a long time.

After the watch is flooded, it is recommended to find a professional repair outlet as soon as possible for the master to check and deal with it, which can reduce your unnecessary losses.

In the case of water ingress into the watch, do not panic, continue to maintain the temperature of the watch (such as wearing the watch all the time) and send it for repair immediately is the best solution.

Watch water ingress treatment:

1. If the watch accidentally gets into the water, you can use silica gel to dry the granules. If water enters the case, you can use the granular substance of silicone to put it in an airtight container with the watch, and after a few hours, remove the watch and the water will disappear.

2. Wear the watch backwards. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours. If the water ingress is severe. Send it to the watch shop to wipe the oil.

3. The above two methods cannot remove water vapor, and should be immediately sent to the repair shop to wipe the oil to remove the moisture of the movement to avoid rust of the parts.

Watch water ingress is one of the common faults of watches, many people wash their hands or rain due to improper protection of the watch caused by water ingress in the watch, after the watch enters the water, it will affect the watch time and dial. What should I do if the watch gets into the water and there are water droplets inside?

What should I do if the watch gets water and then there are water droplets inside? It is normal for the watch to get water, if the water is not serious, but there is a layer of fog in the watch glass, then several layers of toilet paper can be used.

or flannel cloth that absorbs moisture will be tightly wrapped around the table, at a distance of 40 watt bulbs.

Bake at 15 cm for about 30 minutes to eliminate moisture.

Dry the granules with silica gel.

If water enters the case, you can use a granular substance called silicone to put the watch in an airtight container with the waterlogged watch, and after a few hours, remove the watch and the water will disappear. This method is simple and economical, and does not compromise the accuracy or longevity of the watch. The silica gel that has been absorbed many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

Bake hot with an electric light bulb.

If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes to eliminate the moisture. Do not bake the watch close to the fire to avoid deformation of the watch.

Wear the watch backwards. Small pieces of calcium chloride can be applied directly with gauze.

Figure 1) wrapped; Then take out the watch cover and put the calcium chloride wrapped in gauze and the electronic watch seal into a plastic bag and box. After waiting for half a day, you can take out the watch, and you can see the moisture of the electronic watch disappear. If the water ingress of the watch is serious, it can be left for a day.

Send it to the watch shop to wipe the oil.

None of the three methods described above can remove moisture, so you should immediately send it to a watch shop to wipe the oil and remove moisture from the movement to avoid rust on the parts.

How to repair the watch for water ingress: The only good way for the watch to get water is to open the back cover of the watch, treat the movement inside the watch, and then oil each movement part.

Therefore, if water enters the watch, the movement parts in the watch will be stained with water, which will lead to the hazard of rusting parts. Therefore, the maintenance of water ingress in the watch should not only be clear about the steam in the watch, but also maintain the movement in the watch to prevent the harm of rust in the parts.

Generally speaking, there are only three places where water can enter the watch movement: the handle (handle), the watch mask and the back cover. The waterproof device is also installed in these three places: the shank with a rubber ring and a sealing ring.

Add a rubber ring on the threaded edge of the back cover of the shank and other parts, and make the surface tight. With these designs, the watch is waterproof.

1. Do not swim with a 30m watch;

2. Do not wear any watch to the bathhouse, do not wear any watch to sauna;

3. The watch should be maintained every 3-4 years or so, and the waterproof test should be carried out;

4. If the watch is flooded, it should be dealt with in time, and it needs to be scrubbed and maintained by the watch maintenance institution. If the watch is not repaired in time, then the water will rust the steel parts in the watch movement, and the tiny clock parts usually need to be replaced once they are rusty, in addition to the movement parts, long-term contact with water vapor will also make the watch dial, blistering and rust occur.

It can be repaired, the watch can be damaged if it is in water for too long, it is recommended that you repair it as soon as possible.

Watch maintenance and repair can refer to the service center of 702] Joy City Office Building, Xidan District, Xicheng District, Beijing to provide Swiss watch strap customization, cleaning and maintenance, identification, refurbishment, fault repair, watch appearance and replacement of damaged parts, and strap replacement services. Our technicians have undergone strict professional skills training and provide two years of after-sales guarantee services. The service center is guided by the watch manufacturer on the spot**, **transparent, no hidden consumption, no additional charges.

Method. 1. Put the surface face inward, the bottom shell facing outward, and wear it on the wrist, and the water vapor can be eliminated after two hours. If the water ingress is severe, it is best to immediately send it to the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the parts.

Method. 2. If the watch is soaked in water, you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, put it near a 40-watt light bulb about 15 cm, bake for about 30 minutes, and the water vapor in the watch can be moisture. Do not bake the watch close to the fire, so as not to deform the watch by heat.

Method. 3. Put the granular silicone into a closed container with the watch that has accumulated water, and after a few hours, take out the watch, and the water will all disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch.

1.Prepare some paper towels or moisture-absorbing flannel, wrap the watch tightly, place it on a 40-watt light bulb about 5 cm, and bake it for about half an hour. After that, you will notice that the moisture in the movement slowly disappears.

2.Fog can also be removed by basking in the sun. First open the back cover of the watch, then wrap the watch completely with a paper towel or moisture-absorbing flannel cloth, and take it to the sun for most of the day to remove the moisture in the movement.

3.After the watch is flooded, you can open the back cover of the watch first, remove the battery, and use the hair dryer to blow on the watch on low speed. After blowing until it is completely dry, reattach the back cover.

When installing, you can also check whether the sealing ring is aging and broken, and remember that the back cover must be fastened if it is in good condition.

4.Dry the granules with silica gel. Put the silicone granular substance in a closed container with the watch that has accumulated water, and after a few hours, remove the watch and the water will disappear.

1. Self-rescue method for watch water ingress.

1. After the watch gets into the water, take a paper towel to dry the water outside the watch as soon as possible. Then pull out the watch knob and wrap the watch tightly with several layers of paper towels, trying not to leave gaps. After wrapping, put the watch under a light bulb of about 40w for barbecue, and be careful not to put the watch too close to each other during the barbecue, the high temperature will cause the watch to suffer thermal denaturation, about 15cm.

2. The watch is covered with a fine layer of fog, which generally only occurs when the weather changes greatly, and the fog will dissipate by itself after the temperature stabilizes. If you want the fog to dissipate as soon as possible, the best way is to wear the watch backwards, which usually takes an hour or two. However, if the water mist is relatively large, this method is not feasible.

3. The water in the watch can also be brought out with silica gel desiccant, and it is relatively simple to use, find a closed container, pull out the watch handle, and then put the watch and silicone together in the container. Leave it on for a few hours to absorb the moisture.

4. If you can't find the silica gel desiccant, the rice can also be replaced, bury the watch deep in the rice, and after a day, the water will be sucked away. However, there are a lot of fine particles in rice, and when the water is absorbed, small particles may also take advantage of the opportunity, so try not to use this method.

The watch is flooded, and there are the following typesRemedy

The first method: baking with an incandescent lamp.

Wrap the watch with several layers of paper towels, then place it at 15 cm of a 40-watt incandescent lamp, and bake for 5 minutes, and the water vapor in the watch will be evaporated. Remember not to bake for too long, and for watches with leather straps, the strap should be removed first.

The second method: put it together with desiccant.

The water absorption effect of desiccant is much better than that of rice, put the watch and desiccant together, wrap it in plastic wrap, and wait for 24 hours, and it will not cause dust pollution.

The third method: put it in rice.

Rice has a good water absorption effect, and every family has rice, and it is easy to use. After 24 hours of placing the watch in the rice, most of the water is absorbed. Finally, take out the watch and gently wipe off the rice dust.

The fourth method: reverse the watch.

In order not to disassemble the watch, you can wear the watch upside down, wear the watch glass on your arm, and discharge the water vapor in the watch little by little.

Summary. Hello, here to help you find out:1

You can put the watch and desiccant together and wrap it in plastic wrap. Leave it on for 24 hours and the watch will become dry. And there will be no dust pollution.

2.It is possible to put the watch and rice together. Because rice has a strong water absorption effect, most of the water in the watch can be absorbed after 24 hours of putting the watch and rice on it.

Finally, take out the watch. Gently wipe the rice dust off the watch and you'll be fine3You can wrap the watch tightly with several layers of toilet paper or flannel, and then place the watch about 15 cm near a 40-watt light bulb and bake for about 30 minutes until all the moisture is gone.

Special attention should be paid to the fact that the watch glass should not be baked directly close to the light bulb to avoid deformation of the watch glass by heating. 4.Put the watch on your hand and the moisture will disappear after about 2 hours.

5.Put the granular silicone with the watch in a closed container, and after a few hours, you can take out the watch and the water will disappear.

Hello, here to help you find out:1You can relax the watch and desiccant to age together and wrap it in plastic wrap.

Leave it on for 24 hours and the watch will become dry. And there will be no dust pollution. 2.

It is possible to put the watch and rice together. Because rice has a strong water absorption effect, most of the water in the watch can be absorbed after 24 hours of putting the watch and rice on it. Finally, take out the watch.

Gently wipe the rice dust off the watch and you'll be fine3You can wrap the watch tightly with several layers of toilet paper or flannel, and then place the watch about 15 cm near a 40-watt light bulb and bake for about 30 minutes until all the moisture is gone. Special attention should be paid to the fact that the difference gauge of the watch should not be carefully baked close to the light bulb to avoid the deformation of the watch glass by heating.

4.Put the watch on your hand and the moisture will disappear after about 2 hours. 5.

Put the granular silicone with the watch in a closed container, and after a few hours, you can take out the watch and the water will disappear.

If the watch guesses that the water is more serious, remember not to deal with it yourself, so as not to cause unnecessary losses. It is recommended to send the watch with water to a professional maintenance and leakage repair institution for oiling to remove the moisture from the movement and prevent the watch parts from rusting.