How to set up the FAST 150M wireless router to allow desktop and laptop colleagues to access the Int

1. Line: You first start to connect the LAN interface of the network cable to the modem, that is, the cat, and then use another network cable to connect the router to the computer.

2. Computer debugging: After turning on the computer, then open the browser input. Then select Connect to Network. Select Broadband Dialing. You can save it after connecting.

The router belonged to the previous owner, and now you have it in your hands, right? You just reset the router and set it up. The reset method is to put a small stick into the small hole of the reset switch (reset), hold it for more than five or six seconds, until the router is turned off and then light up and then release.

In the past, the wireless router of my classmate was set up and connected to the Internet, and it was disconnected within two days. I bought a fast150m fast wireless router, set up the network connection, and couldn't afford it! I can't afford to set dynamic DDNS and WDS!

The full setting is coming、This IP has changed.、It's just not good! From the beginning of the setup to the completion of the detailed guidance.

Read the manual, if you don't understand, just default and don't change other settings at will.

Go to the routing and select ADSL, enter your username and password, and you're good to go.

First, connect the router to the computer separately, go to the router settings page, and change the router LAN port address, for example, to save and restart the router. Then connect the home network cable to the WAN port of the router, connect the LAN port to the computer, and set up the wireless function interface of the router.

There is a DHCP setting inside, you can see if there is a problem with the setting, which is randomly assigned IP.

Seriously, you said so much above, I still haven't figured out your problem, I use a brand of wireless router with yours.

The desktop computer that you added today can't be used anymore after you unplug it, and what does that mean, do you use wired Internet access or wireless Internet access? This router, if you use wired Internet access, then it can only support 4 machines to access the Internet at the same time, if you are wireless, then there is no limit, as long as there is a signal, you can connect to the network.

After setting up, whether it is your tablet or desktop computer, as long as you search for the signal, enter the correct route, ssid and password, you can access the Internet wirelessly, how can this happen to you, my home router with 3 devices, did not appear your problem.

Is the IP address of the new desktop card set to the specified one? If so, change it to automatic allocation, and the router and the other unit will also check and change to automatic allocation.

Reset the route.

The steps are as follows:

1. Enter the router management IP in the browser, default, press enter;

2. Enter the router administrator account and password, click OK, and the default is admin;

3. Start the setup wizard by default and click Next;

4. Click Router mode;

5. Select the corresponding connection mode, select the PPPoe mode here, and click Next;

6. Enter the account password provided by the ISP and click Next.

7. Turn on wireless, you can modify the SSID, enable the security option, select WPA-PSK WPA2-PSK, enter the password, and click Next;

8. Click Restart.

Method steps.

1.First, connect the RJ45 network cable from the LAN port or network port of the optical modem or ADSL modem to the WAN port of the wireless router, and then use another network cable to connect the RJ45 network cable from the LAN port or network port of the wireless router to the RJ45 interface (network card interface) of the computer.

Then connect the wireless router to the power supply, and the installation of the wireless router is complete.

2.Open a computer browser and enter it in the address bar or, for details, please refer to the router IP or LAN port IP identified on the router body).

The router IP is, but the IP is modified later, so what is entered now is, as for how to modify it and what is the use of modifying it, it will be introduced in detail.

3.Enter the account and password in the pop-up dialog box (the general router account is admin, and the password is admin), and you can refer to the logo on the router body to view the router password.

4.After entering the router setup interface, click "Setup Wizard" as shown below

5.As shown below, click "Next".

6.It is recommended to select "Let the router automatically select the Internet access mode", and ADSL can choose "Let the router automatically choose the Internet access mode" or "PPPoE".

7.If the settings page as shown in the following figure appears, enter the broadband account number in the Internet Access Account field and the broadband password in the Internet Access Password.

If this setting screen does not appear, it means that your cat has an auto-dialing function or your network does not need to dial, so users who do not have this setting can skip this step.

8.As shown in the figure below, wait for the network environment to be tested.

9.As shown in the figure below, the SSID is your WiFi name, fill in your WiFi password in the "WPA-PSK WPA2-PSK password", of course, you can also not set the password, but it is not recommended.

10.Once the setup is complete, tap "Restart".

11.In fact, the wifi setup has been completed, if your wifi can't be connected or there is no wifi, please follow the above to reset the settings. If your wifi can be connected but you can't connect to the network, it may be caused by a conflict between the IP of the cat and the IP of the router.

Change the IP address of "Network Parameters" - "LAN Port Setting", the IP address of the router was originally but since the fiber modem is also this IP address, the IP address was changed to the following figure), here. The wifi setup is all done.

P.S.: If a curious user asks if the cat and the router IP address are, then enter the browser into which setting will enter, here or tell you, will enter the device close to the computer. What does that mean?

Because the router is directly connected to the computer, and the cat is connected to the computer by connecting to the router. Therefore, it will enter the setting interface close to the computer, which can be referred to.