The network speed of the router WDS is unstable, how to adjust the wireless advanced settings

First of all, we type in the address bar of the browser, and then enter the router management interface.

Here, we select "System Tools" and open the option "Change Login Password" to change the login password.

The original username and password are admin, and then everyone chooses their own username and password, and after modification, save it to successfully modify the router login password.

Set the password for the router's wireless signal connection.

When entering the router management interface, here, we open "Wireless Settings" and enter "Wireless Security Settings".

Here, we first need to turn on the wireless security settings, and then choose the security type. Security Tips: To ensure network security, it is highly recommended to use the WPA-PSK WPA2-PSK AES encryption method.

Regarding the authentication type and encryption algorithm settings, I recommend that you still have the default settings of the system, and we will not modify them here. Including the group key update cycle is not modified, we only need to enter the psk password we set. It is recommended to use numbers and letters for the PSK password, which is more secure.

After clicking Save, the router will ask the user to restart the router for the configuration to take effect.

The two routers are too far apart.

1.Both wireless routers need to have bridging capabilities.

2.The wireless name and SSID used by the wireless router must be the same.

3.The wireless channel used by the wireless route must be the same.

4.Both routes have bridging mode WDS enabled, and the MAC addresses of each other's routes are filled in with each other.

5.The wireless encryption mode and password of the wireless route must be the same.

6.It is best to use wireless router products from the same manufacturer, or even the same model, to avoid compatibility problems.

Configuration of Router 1:

2. In the WAN port settings, set the current Internet access mode, in this case PPPoE dial-up.

3. Set the basic information of the wireless, change the default SSID to AP1, enable the bridge function, and enter the wireless MAC address of AP2 in the box below.

Router 4, 1 keeps DHCP enabled.

Configuration of Router 2:

2. In the LAN port settings, change the LAN port IP to :, and then click "Save".

3. The WAN port setting remains the default and unchanged.

4. In the basic settings of "Wireless Parameters", change the SSID to AP2, enable the Bridge function, and fill in the MAC address of AP1 in the box below.

5. In the DHCP service settings, router 2 disables the DHCP service. Then click "Save".

Does your secondary router DHCP stop opening,Be sure to stop turning on, that is, remove the small hook in the box,And then restart,I used to bridge the router and encountered similar problems,Just turn off the secondary DHCO。

The load of the equipment is too large, and it is often turned off when it is not in use, and there can be too many people using it.

1. Connect the line between the network cable, the router and the computer, and start the computer and the router equipment;

2. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface. (If you can't get in, please look at the nameplate at the bottom of the router or the router instruction manual, the default settings of different models of routers are different.) ）

3. An account and password to log in to the router appear in the settings interface, enter the default account and password admin, or refer to the manual;

4. After successful login, select the interface of the setup wizard, which will automatically pop up by default;

5. After selecting the setup wizard, a window will pop up to explain that you can set the basic parameters of the router through the wizard, and click Next directly;

6. Set up step by step according to the setup wizard, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

7. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

8. Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

9. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.