How the protective layer of paint granules is made

The coating granular protective layer is a new type of building material, and the material cost is almost the same, and the roofing coating granular protective layer belongs to flexible waterproofing, saving labor and less pollution. Compared with two felt and three oils with mung bean sand waterproofing, the pollution is small, and it is much better than rigid waterproofing.

1. The masonry protection wall has the best effect, but it should be noted that the wall should be built at the protruding end of the structural bottom plate to prevent the relative slippage between the protective wall and the waterproof layer caused by the settlement of the foundation.

2. Polyethylene foam board (ordinary or extruded plastic board), pay attention to the backfill to be layered and tamped during construction, and it is strictly forbidden to damage the foam board by stone impact;

3. The protective layer of cement mortar, it is difficult to plaster the surface of the waterproof material, and it can be used when the height is low.

4. Other materials such as wood boards, polyethylene foam membranes, etc. can also be used. There is also the practice of poly board and masonry protection wall, and extruded plastic insulation poly board is used between the masonry protection wall and the waterproof layer, which plays the dual role of anti-condensation and protection of the waterproof layer.

This is not easy, the most economical and practical is the bean stone waterproof granular protective layer, the practice is to do the waterproofing, the last coating of a waterproof membrane adhesive, and then the screening and washing of the bean stone evenly sprinkled on the surface with a tool to scrape flat (if there are too many pumice, spray some waterproof membrane adhesive) OK.

Hello, I am happy to answer for you, there are two categories of coating granular protective layers: one is polyurethane waterproof coatings. These materials are generally made of polyurethane and coal tar.

The tar gas it volatilizes is highly toxic and not easy to remove, so it was banned in China in 2000. The Bohewu polyurethane waterproof coating that is still on sale is based on asphalt instead of coal tar or as a raw material. However, when using this kind of coating, it is generally diluted with organic solvents such as toluene and xylene, so it also contains toxicity; The other type is polymer cement-based waterproof coatings.

It is composed of an emulsion synthesized from a variety of water-based polymers and high-quality cement mixed with various additives, and the flexibility of the polymer (resin) is combined with the rigidity of the cement, which makes it excellent in terms of impermeability and stability.

Summary. Hello! Kiss!

The protective layer of paint particles is a new type of building material, which belongs to a kind of painting. Extensions: 1

Its material cost is almost the same as that of the roof coating particle protective layer, which is flexible waterproofing, saving labor and less pollution. Compared with the waterproofing of mung beans on two linoleum and three oil sands, it is less polluting and much better than rigid waterproofing. 2.

Thermoplastics are generally made of petroleum as raw materials for monomer polymerization, and the polymerization products are generally powders, which are not easy to store and transport, and are not easy to process and shape, and are generally granulated by extrusion. Additives such as antioxidants are usually added during the granulation process to increase the storage time of the raw material and give the raw material other functions.

Is the protective layer of paint granules a kind of material for painting?

Please wait patiently for 5 minutes, we are sorting it out, and we will answer you immediately, and please do not end the consultation.

Hello! Kiss! The protective layer of paint particles is a kind of new source of building materials, which belongs to a kind of brushing.

Extensions: 1Its material cost is almost the same as that of the roof coating particle protective layer, which belongs to flexible waterproofing, saving labor and less pollution.

Compared with the waterproofing of mung beans on two linoleum and three hail Hui oil sands, it has less pollution and is much better than rigid waterproofing. 2.Thermoplastics are generally made of petroleum as raw materials for monomer polymerization, and the polymerization products are generally powders, which are not easy to store and transport, and are not easy to process and shape, and are generally granulated by extrusion.

Additives such as antioxidants are usually added during the granulation process to increase the storage time of the raw material and give the raw material other functions.

Dear, I am glad to answer for you: how thick is the protective layer of paint granules in generalAnswer: Dear, hello! <>

The thickness of the protective layer should not be less than 40mm, the thickness of the fine stone concrete protective layer on the roof waterproof layer should not be less than 40mm, the thickness of the fine stone concrete protective layer on the waterproof layer of the basement roof membrane should not be less than 70mm, and the thickness of the fine stone concrete protective layer on the basement floor should be greater than 50mm. Waterproof layer setting and standardized construction method: must be painted 2 3 times, otherwise glass fiber cloth should be added, and the thickness of the cured object coated each time shall not be less than 1 mm, and the next construction should be carried out after it is completely dry (about 5-8 hours).

After painting, another mortar protective layer should be made on the waterproof layer of the paint, and finally the tile collapse should be pasted. Thank you for your patience. The above is my full reply, if you are satisfied with my service, please give a thumbs up, and I wish you all the best!

Peace and joy!

Kiss! Hello, happy to answer your <>

Pro-coating granular protective layer manufacturers are as follows: domestic ranking: 1

Kechuang Environmental Protection: This is a professional pellet manufacturer, product quality and technical level have been widely recognized, is the leader in the same industry in China. 2.

Alcoa Protective Film: This is a state-of-the-art paint manufacturer that provides high-quality coating products and specialized consulting services. 3.

Claude Coatings: This is a state-of-the-art paint manufacturer covering all types of paint products. 4.

Beijing Leichuang Technology: The company is mainly engaged in building decoration materials, which produces all kinds of coating products, quality and competitiveness of the highest quality. 5.

East China Lubricants: The company has a complete production line and professional R&D personnel to produce high-quality coating granule protective layer products. Foreign rankings:

1.Axalta: This is a long-established manufacturer of coatings for industrial, automotive and motorcycle applications.

2.BASF: The company is one of the world's leading chemical manufacturers of high-quality coating products and pellet protective coatings.

3.AkzoNobel: The company is a leading global chemical manufacturer that produces various types of coatings and has a proven track record of training professionals.

4.PPG Industrial Coatings: The company manufactures high-quality coating products, primarily for industrial applications.

5.Genting Coatings: The company manufactures high-quality coating products for different sectors such as automotive, construction and industrial.

Hope mine can help you <>

Do you have any other questions?

1. In the waterproof specification and waterproof project, there is no "paint granule".

2. Self-adhesive coils generally cannot be used in the open, and can be protected with mortar, fine stone concrete rigid layer. It can also be repainted with asphalt or waterproof paint on the membrane, and sprinkled with coarse sand or bean stone before the paint dries, but the cost is high and the effect is not good.