How to paste a single film of a table tennis racket?

Replace the rubber sleeve and keep the bottom plate:

1. Carefully tear off the rubber sleeve, if the rubber sleeve is very firmly pasted, use a hair dryer to heat the rubber sleeve until it becomes soft, and then tear it off. (Note: This method is slightly damaging to the rubber).

2. Apply a new layer of glue to the bottom plate to remove the old glue. This step can be repeated until the old glue has been cleaned up.

3. Paste the new glue according to the glue pasting method.

Replace the bottom plate and keep the rubber:

1. Tear off the rubber carefully, if the rubber is very firm, use a hair dryer to heat the rubber to make the glue soft, and then tear it off. (Note: This method is slightly damaged to the rubber sleeve).

2. Apply a layer of new glue on the sponge surface of the glue to remove the old glue. This step can be repeated until the old glue has been cleaned up.

3. Paste the rubber sleeve to the new bottom plate according to the glue pasting method.

Straight plate paste rubber generally forehand to about 1 cm away from the handle of the grip of the grip of the distance, specifically according to their index finger grip position determined, the backhand is basically aligned with the forehand, if the Zen potato is a straight plate horizontal hit He no, the backhand can be pasted.

Prepare materials: scissors, glue, utility knife, presser stick, racket, rubber.

Steps: 1. Pour an appropriate amount of glue on the sponge to be used, taking care not to use too much.

2. After pouring the glue, use a brush to apply the glue poured on the sponge for pasting, and try to make the thickness of the glue consistent.

3. Pour glue on your own table tennis plank and apply it evenly.

4. Place the sponge and table tennis board coated with glue to dry.

5. Put the table tennis bottom plate flat on the table, put the bottom plate flat on the table, hold both sides of the sponge rubber with both hands, aim at the racket, and gently place the rubber well, paying attention not to bulge.

6. Use a glue stick or a round bottle to lightly press the top of the glue, roll it a few times, let the sponge rubber just pasted on slightly fix, and lay the rubber flat to prevent skewing.

7. After putting it down, press the rubber flat with a glue stick or bottle again to ensure that the rubber is flat and sticky to the table tennis bottom plate.

8. Turn the pasted table tennis board over and place it on a flat table, don't skew it.

9. Use a utility knife or scissors to cut off the sponge rubber that you just pasted.

10. After cutting, use scissors to rest again to ensure the neatness of the edge of the table tennis bottom plate.

11. After cutting the rubber, the work on this side is completed, repeat steps 1-10 to complete the rubber on the other side.

1. Open the rubber package, evenly brush the glue on the side of the rubber sponge, and dry it after brushing;

2. Draw a marking line on the bottom plate;

3. Evenly coat the glue on the bottom plate and dry it after coating;

4. Take a piece of white paper and cover it on the racket, do not press it on the marker line;

5. Compact the rubber and racket marking lines that are not covered by paper;

6. Pull out the white paper and press the racket with your hands or roller to ensure reliable bonding around it;

7. Use a utility knife or scalpel to cut off the excess rubber along the edge of the racket.

1. Prepare sponges, single rubbers, sponge blocks (for brushing inorganic glue), and glue rolling sticks that need to be pasted.

2. Squeeze a little inorganic glue (about the size of a dollar coin) onto the rubber.

3. Brush evenly along a straight line with a sponge block.

4. Wait for the glue to dry. Inorganic glue is transparent when it dries.

5. The sponge end is also coated with inorganic glue in the same way, and wait for it to dry.

6. In order to avoid mis-adhesion, cover a piece of plastic film (or white paper) on the rubber sheet, leaving only one bottom edge for alignment.

7. Align the bottom edge with the sponge, and then pull out the plastic film.

8. Use a rubber rod to evenly paste the rubber and sponge together.

9. Then you can get a beautiful, flat and bubble-free assembly rubber with strong performance.

Table tennis racket viscose glue is organic glue and inorganic glue, which is widely used.

1. The main components of organic glue are rubber molecules and organic solvents, and the rubber molecules left after sol volatilization are cross-linked into polymers to play a role in adhesion.

The proportion of organic solvents in the composition of glue is usually higher than that of rubber, and the commonly used organic solvents are cyclohexane, heptane, etc. This is also the current general glue, its market is much lower than inorganic glue, occupying a larger market.

2. The main ingredient of inorganic glue is inorganic binder, such as cyclohexane, which is often used now. The appearance of inorganic glue is colorless, tasteless, and clear as water. Inorganic glue is currently the most high, and high-grade sponges need to be used.

It is recommended to buy a bottle of special glue, other general glue is not sticky, you can stick it with 502, but your racket will be wasted.

Table tennis rubber sticking:

1. First of all, we will put the things we are going to use in front of us, the position that we can reach, table tennis rackets, two new pieces of rubber, special glue for table tennis, knives, rags, etc.

2. In order to save time, we can first brush one of the two new rubber sheets with glue, pay attention to the brushing should be even, and then brush after it is dry, a total of 2 3 times.

3. Tear off the old rubber on the tennis racket, there will continue to be sponge under the glue, which can not be removed, you can use a fruit knife to cut off the edge, and then tear off the forehand after tearing off the residue with a fruit knife to get the forehand to attack the ball.

4. Brush the woodworking board with the special glue for the table tennis game, brush it at that time to be symmetrical, glue it again after drying, and find that the residual sponge can be removed immediately when it can be glued 2 or 3 times, so as to prevent it from being uneven and harmful to the application of the new set of glue.

5. In the case of waiting for the set of rubber blockboard to dry, we can remove the sponge debris to the actual operation without dirt.

6. After waiting for the set of glue and woodworking board brush 2 or 3 times of super glue to dry, we brush again to glue the woodworking board and the new set of glue together, and press it once along the edge of the outside with your thumb If it is sticky, some positions can not be glued, and you can press it on it in the afternoon, such as cups.

7. After that, glue another piece of glue.

8. Because after brushing many times of super glue, the rubber will expand, after the two new sets of glue are glued, we must use scissors to carry out tailoring along the edge of the outside world, and be as careful as possible while cutting, otherwise it will harm the beauty and generosity.

9. In the end, I scrubbed the rubber with a towel, removed the ash, and then put it into the racket cover of the tennis racket, and I won a big victory.

Precautions

Table tennis glue can not be brushed on the rubber surface of the table tennis ball, glue can only be brushed on the bottom plate of the table tennis racket, and the sponge of the table tennis ball rubber.

If you accidentally brush it on the nine sides of the table tennis card, then it is difficult to remove, you must use a professional table tennis glue remover, so we must be careful when sticking the table tennis glue and brush the glue.