How to glue the table tennis rubber well? The table tennis racket rubber is opened, what glue is use

You can get the sports store where you can buy rackets and let the master help you glue it, after all, they are more professional (gluing, sticking, cutting)...Self-adhesive sleeve glue process: the general new glue is poured and brushed with 3-5 layers of organic glue (note: after brushing a layer of glue, it is necessary to wait for a layer of glue to dry thoroughly and then brush the next layer, and the organic glue is generally completely dry in 5-10 minutes) Two layers of brushing on the bottom plate can be done.

When the rubber is put on the board, a relatively smooth paper skin can be used to separate the rubber from the bottom plate. Glue the rubber to the reserved position, and gently remove the paper. Use cylindrical roller strips (plastic tubes or mousse spray strips can be used instead) ...Flatten the rubber evenly.

Finally, to the cutting: use the art tool knife to carefully cut along the edge of the bottom plate, and try to complete the cutting with the knife without breaking the knife (so that the cut out of the rubber edge line is neat and beautiful)....

There are many ways to stick the shot, if it's the first time to stick the shot, it's better to take the method of insurance points!

First you need a pair of scissors, a larger utility knife, then glue and a glue stick.

Brush the glue once and wait for it to dry until it is not sticky, then repeat 2-3 times, and after it is dry, if you are not sure whether it is dry, wait a little longer, and let it go for half an hour. Brush the bottom plate 2 times and you're good to go. Then aim the rubber to the position you want to glue, hold the rubber with one hand, and roll it down with a rubber roller stick with the other hand, roll it several times.

Then take out the utility knife that is ready for realization, cut the rubber sleeve with even force along the edge of the bottom plate, and then use scissors to carefully cut off the excess rubber edge along the place where the knife has cut, so that the side is glued.

The other side is the same!

Hello landlord; Self-adhesive sleeve glue process: the general new glue is poured and brushed with 3-5 layers of organic glue (note: after brushing a layer of glue, it is necessary to wait for a layer of glue to dry thoroughly and then brush the next layer, and the organic glue is generally completely dry in 5-10 minutes and does not stick to the hands) The bottom plate is brushed twice (horizontally and vertically).

When the rubber is put on the board, a transparent plastic sheet can be used to separate the rubber from the bottom plate. Glue the rubber to the reserved position, and gently remove the paper. Use a cylindrical glue stick to evenly flatten the rubber sheet.

Finally, to the cut: Or use an art tool knife to carefully cut along the edge of the baseplate, as close to the knife as possible. If you don't need to fill the glue, just brush the glue twice.

Well, if you don't understand anything about this question, you can ask it, and if you are satisfied, remember.

If you have other questions, click to ask me for help after this question, it is not easy to answer the question, please understand, thank you! (

Bye!

If you don't understand, you can ask a golfer for help, buy a bottle of special glue and paper cutter, and ask him for help.

It's as simple as it gets. Where did you buy it, where did you go to stick it, because the person who sold the thing has experience and is already familiar with how this thing should be operated

When the table tennis racket rubber is opened, you can use organic glue or inorganic glue, and generally organic glue is fine.

1. The main components of organic glue are rubber molecules and organic solvents, and the rubber molecules left after sol volatilization are cross-linked into polymers to play a role in adhesion. The proportion of organic solvents in the composition of glue is usually higher than that of rubber, and the commonly used organic solvents are cyclohexane, heptane, etc. This is also the current general glue, its market is much lower than inorganic glue, occupying a larger market.

2. The main ingredient of inorganic glue is inorganic binder, such as cyclohexane, which is often used now. The appearance of inorganic glue is colorless, tasteless, and clear as water. Inorganic glue is currently the most high, and high-grade sponges need to be used.

After applying the glue, stick it to the clean glass as soon as the glue is dry. Its purpose is to prevent the glue from volatilizing into the air and enhance the potting effect. It is colloquially known online as "Russian law".

This method is indeed more effective than ordinary methods, and it saves glue. At this time, the ball board is also coated with glue, and a thin layer is enough.

After more than ten minutes, you will find that the rubber gradually breaks away from the glass and warps. This is because the sponge expands and deforms. Try it with your hands, and if you don't stick to it, you can stick it to the bat.

Similarly, the glue on the ball board should also wait for it to dry and not stick to your hands, so that it can be glued firmly and not easy to degum.

1. It sticks more firmly, and you can use universal glue;

2. Use the special glue for table tennis (about 10 yuan for small sticks), brush the bottom plate at least 1 time, brush the rubber at least 3 times, (brush 1 to 2 more times for the new board or new rubber) and then brush the next time (once the horizontal brush and one vertical brush), and so that the board and the rubber are dry before the rubber can be pasted on the board, and the white paper can be placed on the board when pasting the board, aligned a little paste, and then take the paper away, and then roll it with a round rod to compact it after completion. It is also very strong to stick out this way;

3. Use ordinary granular rubber, which is a layer of non-foaming natural rubber or synthetic rubber, and its particles must be distributed on the entire surface with an average density of not less than 10 and no more than 30 particles per square centimeter.

The method of sticking the table tennis racket is as follows:Tools Ingredients: racket, two pieces of rubber, edge banding, special glue, sharp knife, rag.

1. Brush the glue evenly on one side of the rubber first, and at the same time brush the glue on the surface of the racket, not too much, just a thin layer.

2. If you brush too much glue, be sure to wipe off the excess with a rag.

3. Then align the rubber to the racket, if the size and shape are not suitable, we need to use one hand to press the rubber and the racket, so that their position is not cheap, and at the same time take a knife with the other hand to cut off the excess rubber along the edge of the racket. After cutting the edge, if the edge is lacking glue, you can make up some glue appropriately, and then wipe the edge clean with a rag.

4. The other side of the racket is also the same simple beating steps, just repeat it. After both pieces of rubber are glued, apply glue to the edge strip and seal the edge of the racket.

5. Finally, put the racket in a ventilated place to air dry, and this is done.