How to stick the table tennis skin concretely, and how to tear the rubber of the table tennis racket

Here's how:

1. If the glue on the rubber is uneven, it can be removed, and the bottom plate can also be removed, and then brush the glue on the rubber, be sure to wait for the glue to dry completely before brushing the next time, I generally brush the new rubber seven or eight times.

2. Wait until the glue on the rubber is dry, it should seem like there is a layer of brightness, and brush a layer of glue on the bottom plate when the glue is brushed at the end, and the brush should be even.

3. Finally, after the rubber bottom plate is dry, it is good to evenly flatten it with a glue stick, and pay attention not to pull the rubber hard when pressing, so as not to affect the service life.

The glue on the sponge does not need to be torn off, the new board is like this, it is easy to open the glue, this is because there is no glue layer, so the old glue is easy to stick to the glue on the brush on it, just brush it on the board, brush it on the sponge and wait until it is dry, and then play, generally it will not open after you stick it three times.

Professional players stick the glue for the first time to open the sponge, and brush the glue 16 times Of course, the amateur is not so meticulous, when sticking the glue, it is best not to press the rubber too tightly The sponge is not good, it will affect the elasticity Just press it gently by hand.

Approximate steps: Brush special glue on the bottom plate and glue set respectively (Ping Pong physical store, ** available), and dry it naturally (if you need to pour glue, you can brush it several times on the glue). Find a hard transparent plastic paper (such as the film of the liquid crystal display), pad it on the bottom plate, expose a small section of the board surface that has been brushed with glue, take the set of glue and lay it on the bottom plate to align the edges, slowly glue it, pull out a section of the plastic paper, and then stick it well, pay attention to the sticky time, stick it from one end to the other end, and do not leave bubbles.

After all the pasting is done, you can press it once or twice with a cylindrical object, and you don't need to use too much force.

With a thin utility knife (scalpel blade can also be used), cut the rubber along the edge of the baseplate, being careful not to cut the baseplate. If you are afraid that the shrinkage will become smaller after the rubber is torn off, you can first attach the edge protection, and then cut along the edge of the edge protection.

Let's go in and see, I wrote it, there are pictures and steps, it's very detailed.

There are two kinds of rackets, one is the finished racket, which cannot be torn at will; The other is to buy your own racket from the material.

First, the finished product shooting method of tearing rubber:

1. It is best to buy a degumming agent, and then the glue will fall off naturally. If there is no degumming agent, it is the most standard.

The method is to tear from the left and right sides to the middle, do not try to tear from the top to the bottom or from the bottom to the top, it is easy to draw.

2. If it is not easy to tear, ask the store owner to help (you need to pay).

3. The finished racket is generally not too easy to use, and it is really not possible to buy a base plate that is better than the finished racket at 30-50.

Second, the combination of racket tearing method:

1. Start from the bottom right of the handle to uncover a little.

2. The direction of tearing the rubber and the direction of the wood grain of the surface material are torn at an angle of 45 degrees, so it is not easy to draw. Just be careful when tearing, it's a matter of practice makes perfect, and there is nothing technical.

1. Prepare sponges, single rubbers, sponge blocks (for brushing inorganic glue), and glue rolling sticks that need to be pasted.

2. Squeeze a little inorganic glue on the rubber (about the size of a yuan coin) 3. Use a glue brush to spread the glue on the sponge evenly.

4. Apply an even glue to the bottom plate.

5. Wait for the sponge and the glue on the bottom plate to dry (touch the sponge with the back of your hand and the bottom plate will not feel sticky).

Place the bottom plate flat on the table and place a piece of paper on the bottom plate with the paper at some distance from the handle.

6. Hold both sides of the rubber with both hands, aim at the racket, place the rubber gently, gently press the top of the rubber with a glue stick, let the rubber be slightly fixed, and lay the rubber flat to check whether it is suitable for the racket (to prevent skewing).

7. Remove the paper padd on the racket, and then paste the rubber flat on the bottom plate with a glue stick.

8. Use a utility knife to cut the sponge along the edge of the bottom plate.

9. Use scissors to cut the rubber along the edge of the bottom plate (because the sponge has just been cut with a utility knife, so it is not easy to cut the rubber with scissors at this time), and do not hesitate to cut it down.

Summary. Hello dear ! After our inquiry, you need to evenly brush the glue on the bottom plate of the table tennis ball, and you can brush it again when it is dry. Brush the glue evenly on the rubber, and the new rubber can be brushed three times.

Hello dear ! After our inquiry, you need to evenly brush the glue on the bottom plate of the table tennis ball, and you can brush it again when it is dry. Brush the glue evenly on the rubber, and the new rubber can be brushed three times.

Put a rubber protective film on the bottom plate of the glue brushed, which can prevent the rubber from being misplaced and is conducive to the pasting of the rubber. Place the rubber on the bottom plate, press it evenly with a glue stick, and gently remove the rubber protective film. Use scissors to remove the excess rubber, and be careful not to cut the bottom plate at the edges.

After that, you can glue the other side in the same way!

Yes, and really high-end.

Table tennis rackets. It's all bottom plates and.

Glue. Sold separately, everyone can match and paste according to their own needs.

Rubber. If you generally need professionals, it will be better, you need professional glue and rolling.

Glue sticks. and other supplies that you can go.

Youge.com. Take a look, his introduction is more detailed.