How to clean real stone paint, how to clean real stone paint?

Real stone paint construction technology 1. Base surface treatment: 1 1. Clean the base surface: remove the floating ash, cement and oil and other attachments on the construction surface.

1 2, the convex part that seriously affects the flatness of the sanding treatment, and to meet the flatness requirements: (3mm) 1 3, with a coarse putty to fill the obvious depression or hole, after drying, it will be sanded to meet the flatness requirements (3mm) 1 4, construction requirements: 1 4 1, the base surface is clean and tidy, hard and firm, no debris attached.

11 2. The flatness meets the requirements (2mm). Second, the rough layer construction: 2 1, the construction ratio:

Powder:Glue:Clean Water =10:

1: When using, mix one part of cleaning water and one part of glue evenly, and then mix AW-55, use a hand drill to operate, and add AW-55 while stirring until it is evenly mixed. 2 2. The prepared putty should be placed for up to 4 hours, and it cannot be used for more than 4 hours, and the solidified slurry cannot be used.

2 3, a full batch of putty; When the greasy layer turns white, sand the greasy layer to remove the marks; 2 4. The greasy layer needs to be cured with water 3 4 times to make it more completely cured. 2 5: Construction Requirements:

2 4 1, flatness meets the requirements ( ; 2 4 2, the greasy layer has no obvious marks, and the surface is smooth; 2 4 3. The adhesion is qualified, and there is no powder loss phenomenon when picked with nails. 3. Closed primer construction: 3 1. Dilution ratio:

Direct construction, no dilution required; 3 2. Construction method: drum; 3 3, construction requirements: 3 3 1, roll coating; 3 3 2, the construction is uniform, no leakage, and the dosage is reached; 3 3 3, dry time:

6 hours. Fourth, real stone paint aggregate construction: 4 1, construction method: spraying with a spray point spray gun 4 2, the number of construction times:

Twice: the first time plays the role of covering the bottom; The second pass requires the same effect as the board, and the interval between the two passes is 2 4 hours; 4 3, construction requirements: 4 3 1, uniform, no bottom; 4 3 2, to achieve the required effect; 4 3 3, dry time:

If the temperature is too low for 1 day (sunny day above 250C), it needs to be extended according to the site conditions until the aggregate layer is dry. Fifth, the construction of overlay paint: 5 1, construction method:

Spray coating; 5 2. Number of construction times: one time; 5 3, construction requirements: 5 3 1, uniform construction, no leakage; 5 3 2, to achieve the required gloss and dosage.

6. If you need to do lattice joints, you need to carry out the construction of real stone paint aggregates; The black seam is made of water-based black oil.

Take a brush and a feather duster to make it.

1. Putty knife.

It can be shoveled directly with a putty knife, which is a real stone paint shovel for the kind of surface that does not need to be carefully protected.

2. Wind oil essence.

If the real stone paint gets the clothes or gets the surface that can't be scratched, you can use wind oil essence if the amount is small.

3. Alcohol. If the amount is relatively large, soak it in water for a period of time before cleaning, or wipe it with alcohol, gasoline, etc., if it really still does not work or the area of the treated surface needs to be removed is too large, it is recommended to ask a special cleaning company to deal with it.

1. Real stone paint.

When there are stains on the wall, you need to use salt to clean the stains, gently wipe the real stone paint wall with a rag soaked in warm water, and clean it with warm water to remove the stains. If you accidentally splash coffee stains, fruit stains, etc. on the wall of real stone paint, you can use vinegar to wipe it off, and finally use clean warm water to wash it. Among them oxalic acid.

and acetic acid are good cleaning agents for real stone paint.

2. Real stone paint is a kind of paint with a decorative effect similar to marble and granite. It is mainly prepared with natural stone powder of various colors, which is applied to the imitation stone effect of the exterior wall of the building, so it is also called liquid stone.

How to clean the barrel of real stone paint pro! Hello, glad to answer for you. Treatment method: Liquor or alcohol decontamination liquor or alcohol (alcohol is better) also has a certain function of removing real stone paint barrel paint, first pour alcohol on the painted clothing point.

Then rub it with your hands without stopping. Repeat this a few times and the paint on the basic clothes will dissolve, and then wash it off with laundry detergent. If there is a small amount of real stone paint bucket paint on the clothes that are decontaminated with rice washing water, you can use the rice washing water at home every day to wash it, but you have to scrub it with force.

Soak it in rice water for a day and a night, and then scrub it by hand. This can also be removed. The real stone paint barrel paint must be blistered with water, it is recommended to blister it with water immediately after the paint is used up, so that it is easier to clean, if it takes a long time, it will be more difficult.

You can fill it with water and blister it will fall off for half a month, or you can use a cleaning ball to wipe it, this is very simple, soak it in hot water for a while, and wait for the paint to melt and brush it with a brush a few times. Hope mine can help you! Do you have any other questions?

1. Use a sponge to clean the real stone paint. Soak the sponge in cold water and squeeze out the excess water. Gently wipe with a sponge and dry with a soft cloth.

2. If simple cleaning does not remove the stain, use ointment (paper or powder material used to absorb stains). The ointment can be made of heavy calcium carbonate and hydrogen peroxide, or a chemical reducing agent can be selected depending on the stain.

3. Prepare ointment. If you are using a powdered ointment, use stain removal medication until it thickens, as well as peanut butter.

4. Moisten the stain with distilled water. This will fill the porous surface of the marble, separating the chemical remover from the stain.

What can be cleaned off with real stone paint: 1. Use oxalic acid diluent to clean it. Oxalic acid is mainly used as a reducing agent and bleaching agent, and is used in the production of drugs such as antibiotics and borneol, as well as solvents, dye reducing agents, tanning agents, etc., for the extraction of rare metals.

2. Go to a large car wash and buy a glass cleaner, the effect is also quite good. 3. You can use spraying protective film to protect it, if you can't buy filial piety, you can use a disposable tablecloth for the restaurant to protect the front, and do a good job of bonding the protective film under the perforation. You can try all of these methods.

Extended information: Advantages and advantages 1: strong decoration with imitation of natural stone, marble, granite thick paste coating.

Natural color, with the texture of natural stone, read and judge to change a variety of lattice design, can provide a variety of three-dimensional shape of the pattern structure, can visually highlight the elegance and solemn beauty of the whole building, is the best substitute for the exterior wall dry hanging stone. Advantage 2: It can be used on a variety of substrates such as cement brick walls, foam, gypsum, aluminum plates, glass, etc., and can be painted arbitrarily with the shape of the building.

Advantage 3: Water-based environmental protection real stone paint adopts water-based emulsion, which is non-toxic and environmentally friendly, and meets people's requirements for environmental protection. Advantage four:

Good stain resistance, 90% dirt is difficult to adhere, after the rain washes, it is as bright as new, and manual cleaning is easier.

Real stone paint is a high-strength paint that usually requires the use of special tools and chemicals to remove. Here are some ways to remove real stone paint:1

Use of chemicals: Paint removers or solvents can be used to soften and dissolve real stone paint. Apply the chemical to the surface of the real stone paint, wait for a while, and then use a scraper or a high-pressure water gun to remove it.

2.Use a high-pressure water gun: A high-pressure water gun can wash off the paint on the surface of the real stone paint.

However, this method may damage the substrate of the surface, so it needs to be used with caution. 3.Use a heat gun:

A heat gun heats up the paint on the surface of real stone paint, making it soft and easy to scrape. However, this method needs to be used with caution so as not to damage the substrate. 4.

Use mechanical cutting tools: You can use mechanical cutting tools, such as chainsaws or cutters, to cut off the paint on the surface of real stone paint. However, this method may damage the substrate and needs to be used with caution.

Regardless of which method is used, it is important to pay attention to safety and follow the relevant operating procedures and safety measures. It is advisable to conduct a trial to determine the most suitable method before proceeding to remove the real stone paint.

1.Use Bu Xiaoqi vinegar ash solution: mix vinegar and water in a ratio of 1:1, and then add dust, the effect will be better. Use a towel to rub the liquid on the real stone paint, wait a while, and then scrub with a brush and water.

2.Use sodium nitrate aqueous solution: dissolve 20 grams of sodium nitrate in 200 ml of boiling water, stir well, add 500 ml of vinegar, and then wipe it on the real stone paint with a soft cloth.

3.Remove the real stone paint with washing hand liquid: apply the hand sanitizer to the real stone paint, after applying it for a certain period of time, rinse off the hand sanitizer with water, and then wipe it with a rag to remove the real stone paint.

It is best not to brush directly, otherwise it will be easy to leak if it is dirty in the future. Generally this is the step:

Flour agent: The interface agent must be brushed and brushed evenly.

Cracks: In general, use kraft paper tape and white latex to stick the cracks (but there is no guarantee that 100% will not crack again).

Leveling: uneven walls need to be leveled, generally gypsum is more commonly used, and the uneven difference is better than centimeters.

Patching: Generally, non-load-bearing walls such as light walls and insulation walls need to be patched, try to choose a better texture wall cloth and white latex, if there is a condition, you can use mesh cloth, the relative anti-cracking effect will be better.

Putty: It is better to choose putty with higher particle fineness and harder texture, and you can also add a certain amount of white latex to the putty, which can improve the hardness of the putty.

Grinding: try to use finer sandpaper, generally softer putty (such as 821) with 400-500 sandpaper, harder texture (such as wall lining, easy to quack) with 360-400 is better, if the sandpaper is too thick, it will leave a deep sand mark, and the paint can not be covered. After sanding, the wall must be thoroughly cleaned to avoid too much dust and affect the adhesion of the paint.

The difference between bumps and bumps does not exceed 3 mm.

Primer: The primer must be brushed evenly to ensure that every part of the wall is brushed, if the wall eats a large amount of paint, the primer is best to add a little more water to ensure that it can be painted evenly. Don't think that just because it's a primer, it's okay to use a roller that is a little worse, the effect of the primer will directly affect the effect of the topcoat, and you should use a roller with the same texture as the topcoat.

Rub it repeatedly with thinner on the real stone paint, and the real stone paint will be diluted and softened, and it can be easily wiped clean.

You can wash off paint with gasoline or banana water.