How to solve the frequent network disconnection of Tengda FH456 high power wireless router?

Is it disconnected from the wireless signal connected to the router, or is it disconnected from both wired and wireless?

If you just connect to the wireless signal to surf the Internet, the connection will be disconnected, open the browser to enter, click System Management - Wireless channel to 4, channel bandwidth to 40MHz, click OK. Try it after clicking Restart your device.

If the wires and wireless are dropped, enter when the connection is dropped, click on the Internet settings, look at the network status, if it shows that it is normal to be networked, it shows that it is in the network or not networked, you can click System Management - WAN port rate, 4m below the broadband selection of 10m half-duplex, 4-10m selection of 10m full duplex, 10m-20m selection of 100m half-duplex, 20-100m selection of 100m full-duplex, click OK. Click System Management - Restart Router to try.

The wireless router is always disconnected from the network solution:

Analysis and solution: 1. Check whether the wireless router has poor contact, plug and unplug the power supply many times, shake the antenna, and check whether the network is normal.

2. Check whether the router firmware version is too low and upgrade the firmware.

3. Check whether the computer is poisoned, which causes too much Internet traffic and makes the router overloaded and disconnected.

5. The most fundamental way is to buy a good version of the latest version of the wireless router, which will basically not drop the line.

Tengda FH456 router configuration is simple, but for users who do not have a network foundation, there are still certain difficulties in completing the installation of the router and the setting of wireless WiFi, this article I mainly introduce the setting method of Tengda FH456 router wireless WiFi!

1. WiFi name and password settings.

The setting interface of the TENDA FH456 router.

2. Click "Internet Settings" - under the "Wireless Encryption" option on the right, set "Wireless Signal Name" and "Wireless Password" - click "OK".

Tengda FH456 router wireless wifi name and password settings.

Note: (1) The name of the wireless signal is best set by letters and numbers; Do not use Chinese, because some mobile phones, laptops and other wireless devices can not identify Chinese wireless signals, resulting in the situation that the wifi signal cannot be searched.

2) The wireless password should be set with a combination of letters, numbers, and upper and lower case, and the length should not be less than 8 digits.

2. WiFi timer switch setting.

On the setting interface of the Tengda FH456 router, click "WiFi Timer Switch" - select "On" on the right - set "WiFi off time period" - click "OK".

Tengda FH456 router wireless wifi timer switch setting!

How to set up a wireless router:

1. Open the browser and enter it in the address bar;

2. Enter the account number and password in the pop-up form;

3. Enter the corresponding account and password in the new interface;

4. Set the username and password of the router wireless connection, and click "Save".

A wireless router is a router that is used for users to surf the Internet and has a wireless coverage function.

A wireless router can be seen as a device that sends broadband network signals from the wall of your home to nearby wireless network devices (laptops, Wi-Fi-enabled mobile phones, tablets, and all Wi-Fi enabled devices) through the antenna.

Popular wireless routers on the market generally support four access modes: dedicated line XDSL cable, dynamic XDSL, and PPTP, and it also has some other network management functions, such as DHCP service, NAT firewall, MAC address filtering, dynamic domain name and other functions.

Wireless drops: 1Open the browser and enter the router settings interface in the ** bar, click System Management--- Wireless channel change to 4, channel bandwidth use 20MHz, click OK, and click Restart the device.

Wired and wireless are dropped:

Enter the router setting interface, click the system management --- WAN port rate, select 10M for 4-10M, select 10M for 10M-100M broadband, and click OK. Restart the router --- click System Management.

Generally, Tengda router is a router produced by Tengda company. Tengda's scientific research technology has always been at the forefront of the industry, leading the technical direction of network products. The company has a group of excellent, innovative high-tech talents, who focus on the research and development of "tenda" series of network products with independent intellectual property rights.

The products include wireless series, gigabit wired series, 100 gigabit wired series, covering various categories including wireless AP, router, switch, network card, modem, optical fiber transceiver, etc., and the products have passed the national 3C, THE U.S. FCC, and the European Union CE certification.

The setup method of Tengda FH456 wireless router is as follows:

1. Connect the line between the network cable, the router and the computer, and start the computer and the router equipment;

2. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface.

3. An account and password to log in to the router appear in the settings interface, enter the default account and password admin

4. Set up step by step according to the setup wizard, choose the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

5. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

6. Set the wifi password, try to make the alphanumeric combination more complicated and not easy to be rubbed into the network.

7. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can surf the Internet normally after restarting the router.

You first confirm whether the wifi signal connected to the route will be disconnected, or whether the wiring from the 1 2 2 interface of the router to the computer will also be disconnected.

1.If you are only connected to the wifi Internet connection, you can adjust the wireless channel of the router interface, and the setting method is as follows:

Log in to the interface of the router, click on the menu "System Management" - "Wireless Parameters" - "Wireless Channel" to select, these three channels, less interference, more stable, click "OK" after setting, and then click on the menu "System Management" - "Restart the router", and the data can be saved successfully after restarting.

2.If the wireless or wiring network is disconnected, you can open the browser to enter, click "System Management" - WAN port rate, select 10M for 4-10m, select 100M for more than 10m, click OK, click on System Management, and restart the device.

The wireless wifi of the router can be used normally, and the router needs to be set up in the system, and the setup steps are as follows:

2. Then open the browser and enter the management address and login password of the router.

3. After logging in to the background, click the setup wizard, and then fill in the corresponding parameters according to the wizard instructions.

6. After the wireless setup is completed, click Save, and then restart the router to use it normally.

The router settings are as follows:

1.Enter the address you see on the router in the browser, generally, of course, if you use ** online to access the Internet, then you need to prepare an additional modem, commonly known as "cat").

2.Then enter, enter the corresponding account and password, generally the new ones are admin

3.After entering the operation interface, you will see a setup wizard on the left, and Attack on the Entry (usually pops up automatically).

4.Enter the setup wizard interface.

5.Click Next, enter the Internet access mode settings, you can see that there are three Internet access options, if it is dial-up, then use PPPoE. Dynamic IP can be used by plugging the computer directly into the network, and there is a DHCP server on the upper layer.

The static IP is generally a private line or something, or it may be a cell bandwidth, etc., and the upper layer does not have a DHCP server, or wants to fix the IP. As I dial up, I choose PPPoE.

6.If you choose PPPOE dial-up Internet access, you need to fill in the Internet account and password, which should be understood, and there will be an account number to open broadband, and you can fill it in.

7.Then the next step is to enter the wireless settings, you can see the channel, mode, security options, SSID, etc., generally SSID is a name, set the name and password, and then the mode mostly uses 11BGNThe wireless security option is to choose WPA-PSK WPA2-PSK, which is so safe that it will not be easily cracked and rubbed by the network.

8.The next step is to set it up successfully, click Done.

You can buy a telecom mobile phone in the Anhui Telecom online business hall, and the network hall will handle the contract machine to give a high phone bill, you can buy the machine at 0 yuan, which is very discounted, and at present, a number of brands of 4G models are fully listed!