How to set up the connection of Tengda wireless router 307?

Here's how to set up your router:

1. Line connection:

a.Connect the network cable from the cat to the router (WAN port), and then connect the network cable connected to the computer to the router (any port numbered 1, 2, 3, 4).

b.Connect the broadband cable to the router (WAN port), and then connect the network cable connected to the computer to the router (any port numbered 1 2 3 4).

2. Log in to the router interface.

In the browser, type: Enter, enter in the pop-up page: admin and click "OK".

3. Set up the router to surf the Internet.

Before setting up the Internet access, choose the correct Internet access method: Generally, there are three types as follows:

ADSL dial-up: Usually to access the Internet (when not connected to the router) need to click on the broadband connection, dial-up is successful before you can access the Internet, you should choose the Internet mode, Internet access and Internet password correctly enter the broadband and password, you can.

Automatically obtain an IP address: If you usually surf the Internet (when you are not connected to the router), you only need to set the local connection of the computer to automatically obtain the IP address to access the Internet, you should choose this Internet access method.

Static IP: If you need to fill in a fixed IP address in the local connection to access the Internet (when you are not connected to the router), you should choose the Internet access method, log in to the interface of the router, click "Advanced Settings" - "WAN Port Settings" to select the static IP mode "Static IP Mode", and enter your fixed IP address, subnet mask, gateway, DNS domain name server and other parameters correctly.

4. After setting, click "Advanced Settings" - "System Status" to check whether the connection status of the WAN port shows that it is connected, and whether the corresponding connection mode is displayed correctly.

The corresponding connection mode for ADSL dial-up is: PPPoE

The connection mode corresponding to the static IP address is the static IP address

**The following is how to set it up

The steps to set up the Tengda 307R wireless router are as follows:

1. First of all, turn on the router to work, plug the network cable of the external network into the WAN port, and then plug the network cable connected to the computer into a LAN port casually.

2. After connecting the wireless router, enter the IP address of the router in the address bar of the computer browser.

3. After connecting, you will see that you will enter the corresponding login user name: admin and password: admin.

4. Enter the operation interface and click the Setup Wizard.

5. Enter the interface of the setup wizard and select the Internet access mode setting.

6. Click Next to enter the Internet access mode settings, and you can see that there are three ways to access the Internet. If it's dialing, then use PPPoE. Dynamic IP can be used by plugging the computer directly into the network, and there is a DHCP server on the upper layer.

The static IP is generally a private line or something, or it may be a cell bandwidth, etc., and the upper layer does not have a DHCP server, or wants to fix the IP.

7. If you choose PPPoE dial-up Internet access, you need to fill in the Internet account and password.

8. Then click Next to enter the wireless settings, you can see the channel, mode, security options, SSID, etc., generally SSID is a name, you can fill in casually, and then the mode mostly uses 11BGNFor wireless security options, choose WPA-PSK WPA2-PSK, which is so safe that you won't let people hack and rub the network. Click Next to set it up successfully.

9. Click Done, the router will automatically restart, and the router setup will be completed.

P2P LAN Speed Limiter Find the IP of the computer you watch the movie yourself and the speed limit is 100KB.

What you're talking about should be normal!

Both of your computers can access the Internet normally (whether it's slow or not), which means that there is no problem with the routing settings.

As for the speed limit and broadband range, let's take a closer look at the manual!

However, it is estimated that even if this aspect of the setting is effective, it will not be very satisfying to you.

Hello! The steps to set up the Tengda FH303 wireless router are as follows:

1. First of all, after connecting the wireless router, you need to check whether it is powered on and whether the wireless router is running normally.

2. After checking that it is correct, check the instructions on the bottom of the router, open the browser and enter the router IP, and then press Enter to enter, at this time a dialog box pops up, you need to enter the account name and password, there will be at the back of the router, in general: account name: admin password:

admin。

3. After entering the password behind the router, you can log in to the settings page of the router.

4. Click on the setup wizard on the page and follow its requirements step by step.

5. Click Next to enter the account password setting, this account password is the account password of the current network network, if you don't know, you can consult the network operator.

6. After setting the account and password for surfing the Internet, the function of wireless Internet access is set, set the wifi name and wifi password, it is recommended that the password is not too simple, it is easy to be cracked, and the encryption method can be recommended by the system.

7. Click Done, restart the router, and the settings have been successful.

If your router cannot connect to the network after setting, please log in to the router interface, click "Advanced Settings" - "System Status" to check the connection status of the WAN port connection, and check the following troubleshooting methods according to your WAN connection status:

The WAN port displays the solution to the failure of the connection.

The WAN port displays the troubleshooting method in the connection.

The WAN port shows that it is connected but cannot connect to the network.

If the Internet parameters are only for home use, you don't need to set them specifically, just set the wifi password.

Tengda wireless router setup method:

Home Network Environment Cabling]:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoE Dialing] (some are ADSL dialing), enter the username and password (provided by the network service provider) according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

Turn on the router's wireless function].

1. Select Wireless Settings --- Basic Settings.

2. Check [Turn on wireless function] and click Save.

Set wifi password].

1. Wireless Settings - Wireless Security Settings - Select [WPA-PSK WPA2-PSK].

Authentication Type: Automatic.

Encryption algorithm: AES.

The PSK password is the wireless password. Set the required password.

Wireless Copy Router Setup Tutorial.

Hello! The specific setting method of Tengda Wireless F305 wireless router is as follows:

1.Connect the power supply of the router, and then plug one end of a network cable into the network port of the computer, and the other end into the LAN port of the router.

2.Open the browser of the computer, enter the IP of the router in the address bar (the IP of most products is, click the enter key to enter the settings page of the router, the username is admin, the password is blank, click to log in, and enter the settings home page of the router.

3.Once you're logged in to the home page, select Manual settings. Then select Manual Internet Settings, and Home Dial-up users select the PPPoE connection type.

In the username and user, enter the username and password given by the ISP provider (Netcom, Great Wall, Telecom, Tietong, Cable, etc.) correctly. The connection method is always (or automatic.) Model, version may be different) mtu value is 1492.

The save is done.

4.Wireless routers also have a wireless encryption to ensure the user's wireless security. Select the wireless settings on the main page of the router's settings, select an encryption method in the security mode, any one of WEP, WPA, or WPA2, and then enter 8 or more Chinese characters or numbers as the wireless password in the security key, and the router settings will be completed after saving the settings.

5 After the setting is completed, the router will automatically restart, and the external network cable can be connected to the WAN port of the router to use.

1.You can connect the broadband cable to the routing WAN port, and use one network cable, one end to the computer, and one end to the routing 1, 2, 3 interface.

2.Open your computer browser and enter the router settings interface in the ** bar.

3.If you don't connect to the router, the broadband line is directly connected to the computer and you need broadband dial-up to access the Internet, the router selects ADSL dial-up for Internet access, if you don't need to dial up, you can select Auto Get for Internet access, click "Wireless Encryption" to set the 8-digit password and click OK.

4.Click "For other Internet access type settings, please click Advanced Settings" - Running Status - WAN Port Status to show that you can access the Internet when you are connected.

If it shows that the connection is being made, then you can clone the MAC address, click Advanced Settings - MAC Clone, Manually Clone - Clone MAC Address, and click OK if you see that the address does not start with C8:3A:35.

When cloning, you need to take a network cable to connect the computer to any one of the router 1 2 3 interfaces, do not connect the wireless signal of the router ).

5.Restart your router --- clicking System Tools.

After restarting, go to the advanced settings again to check the connection status, and it shows "Connected", then you can surf the Internet.