Wireless mouse automatic drift, what s going on?

That's a light sensory mistake! It's not just the optical mouse that has that problem! Mechanical mice sometimes have them too!

It's just that the mouse detects that it is moving slowly, because the sensitivity is too high. Probably a misinterpretation. Because I can't say whether it's high sensitivity, or the moment I put the mouse, the mouse is not put well, and the light receiver detects that the mouse is moving slightly.

The reason is that there are a lot of software aspects, in terms of Trojans, viruses or drivers A good wireless mouse can not be driven but I see if your mouse is dirty You first get other machines to see if it is a mouse problem If so, you can only go to the manufacturer to see if you are concerned about the warranty time?

The first explanation is. There are ghosts The second explanation is that your infinite mouse has to be repaired or replaced at the place where it was bought!

The wireless mouse will float and delay when laughing! What is the solution, here's how.

1. First of all, on the desktop of your computer, find the "Control Panel" option in all programs.

2. Then after entering the control panel page, click on the "System and Security" button.

3. After that, enter the system and security page, and click the "Mouse" button in the device and printer.

4. Finally, find the pointer option, and then find the "Select pointer movement speed" in the movement bar, and slowly adjust the mouse movement speed, when you feel that the mouse is normal, you can close the mouse properties page.

Wireless mice sometimes drift, mainly due to the following factors:

1.Signal interference: Wireless mice use radio waves to communicate, and surrounding electronic devices, wireless**, etc., may also use the same frequency, resulting in signal interference, resulting in unstable mouse movement.

2.Low battery: Wireless mice need to be powered by batteries, and if the battery is too low, the signal may be weakened or lost, resulting in unstable mouse movements.

3.Receiver issues: The receiver of a wireless mouse can sometimes become loose or damaged, causing unstable mouse movements.

4.Excessive dust on the bottom of the mouse: If too much dust or dirt accumulates on the bottom of the mouse, it can cause the mouse to move unsteadily.

In response to these problems, the following measures can be taken to solve the problem of wireless mouse drift:

1.Change the channel: In the settings of the wireless mouse and receiver, try switching channels to avoid interference with other devices.

2.Replace the battery: Replace the mouse's battery regularly to make sure it has enough power.

3.Replace the receiver or reinstall it: If the receiver is damaged or loose, you can replace it with a new receiver or reinstall the original receiver.

4.Clean the bottom of the mouse: Regularly clean the bottom of the mouse from dust and dirt to keep the bottom of the mouse clean.

Mouse float refers to the phenomenon of free movement of the mouse when the computer is operated, which is generally caused by the failure of the mouse device or the lack of computer memory.

1. If the mouse is faulty, you can use the precise method to check the mouse, check whether there is an open circuit, short circuit, etc., if not, you can try to replace the mouse or update the driver.

2. If it is caused by insufficient computer memory, you can clean up the computer junk files, clean up the computer memory, or try to upgrade the computer memory to improve the speed of the computer's flushing and burial.

In order to prevent the mouse from drifting, in addition to the above operations, you should also pay attention to regularly checking and cleaning the computer, preventing various failures of the machine from sleepy, chattering, and preventing the normal operation of the computer to prevent the occurrence of mouse floating.

Method 1:

1. Generally, there is a small button on the wireless mouse, some on the side and some in the middle;

2. Press and hold this small button;

3. While holding down the button, move the mouse at a slower speed, and release the button after a few seconds to automatically complete the setting and slow down the mouse.

Method 2: 1. Open the control panel of the computer;

2. Find the hardware and sound in the control panel;

3. Find the mouse;

4. Select "Pointer Options" in the mouse;

5. Adjust the speed of the mouse pointer according to the needs of use.

It may be that there is dust in the laser projection port under the mouse, clean it up.

It may be that the battery needs to be replaced.

If the wireless mouse is not responsive, it may be necessary to replace the battery. If you put the pointer moving, change to a better mouse pad, generally because the positioning of the mouse is not too accurate.