How to make homemade soap, how to make homemade soap?

Methods of making homemade soap with lard and caustic soda:

Put 20 grams of lard, 7 grams of sodium hydroxide and 50 ml of water in a beaker and heat with an alcohol lamp. While heating, stir constantly to allow the lard and sodium hydroxide to fully react. Because the reaction is relatively slow, this period of reaction time is relatively long.

During the reaction, water should be added several times to make up for the water lost due to evaporation.

When you see that the surface of the reaction mixture is no longer floating with a layer of molten ** fat (i.e., lard that has no effect), it means that the lard and sodium hydroxide have basically reacted completely, and the heating can be stopped. Then add 50 ml of hot saturated table salt solution to the beaker while it is hot, stir it thoroughly, and then let it cool to precipitate the sodium stearate from the mixture.

Finally, the sodium stearate solid floating on the top layer of the solution is removed, and the solution adsorbed on the surface of the solid (which dissolves glycerin, table salt, and unfinished sodium hydroxide) is rinsed with water, and after drying and molding, it is made into a piece of soap.

There are three keys to doing this experiment well:

1.The reaction time between lard and sodium hydroxide must be sufficient, and the heating must not be stopped until the surface of the mixture is not visible to the floating oil. If the reaction is incomplete, the soap will contain excess oil wax and sodium hydroxide, so that the decontamination ability of the soap will be reduced, and it will be more alkaline.

2.During the reaction, don't forget to replenish water. The mixture should always be kept with about 50 ml of water.

3.After the reaction, the volume of the mixture should remain close to that before the reaction. After sodium stearate is precipitated, there is still a certain amount of water in the mixture, so that glycerin, sodium chloride and unfinished sodium hydroxide are left in the water, if there is too little water, these three substances will mix into the soap, affecting its quality.

The method and recipe of soap are as follows:

12 ounces of distilled water, 1 can of vegetable shortening, 6 ounces of lye, 8-8 inches of container.

Step 1: Pour the shortening into the enamel pot and place on the stove to melt. Heat the lye in another enamel pot.

Step 2: Pour cold distilled water in a glass bowl and slowly pour the lye into the water. Stir constantly with a wooden spoon until the mixture is clear.

Step 3: Pour the shortening in another glass bowl and add the above lye and distilled water mixture. Pour in slowly and stir constantly. Make sure that the heat of the two liquids can be touched by hand.

Step 4: When the above solution becomes viscous, you can add different additives, spices, oils or herbs and mix well.

Step 5: The next step is to pour the solution into a container and place the mold in a warm and insulated place to keep it for more than 24 hours.

Step 6: Cut the above large fiber search soap into the desired pieces and store it in a dry place to dry. They will be ready to use after three weeks. After learning how to make your own lye soap, it's time to try your own home soap.

How to make homemade natural soap.

Step 1: Mix rosemary and lavender leaves and grind them into a powder with a food processor.

Step 2: Bring the water to a boil and pour it into a glass bowl and add 6 tablespoons of the above powder.

Step 3: After 10 minutes, add the rosemary and lavender essential oils to the bowl.

Step 4: Melt the glycerin soap in a saucepan, mix the above solution and stir continuously until smooth.

Step 5: Pour the mixture into the mold and let it sit for at least a month.

Step 6: After a month, remove the soap from the mold. You can wrap the soap in plastic film and butter paper and store it in a lead erection.

Ingredients: 500 g of glycerosaponin, a handful of walnuts, 50 ml of argan oil, soap molds, a tablespoon of essential oils.

1. The first step is to crush the walnuts with a spoon, as shown in the figure below.

2. In the second step, the glycerol saponine is melted in water, as shown in the figure below.

3. Add argan oil to the melted glycerol saponine, as shown in the figure below.

4. Add the chopped walnuts to the pot, as shown in the picture below.

5. Add the essential oil to the soap and stir well, as shown in the figure below.

6. Pour the prepared soap into the mold, as shown in the figure below.

7. As shown in the figure below, the soap is ready.

Homemade soap is a fun and rewarding handmade activity, as well as a sustainable and eco-friendly option. In this post, I will share some of the processes and tips for making soap.

Step 1: Preparation.

Before you start making soap, you need to prepare some tools and raw materials. These tools include: gloves, goggles, stirring spoons, measuring cups, electronic scales, containers, and molds. Raw materials include: vegetable oils, lye, water, flavors and colours.

Step 2: Measure and mix the raw materials.

The first step is to accurately measure the ratio of vegetable oil, lye and water. The ratio commonly used is 6:2:

2。The lye is slowly added to the water and then to the vegetable oil. Stir the mixture with a stirring spoon until it is homogeneous.

This process takes a while and usually takes more than 30 minutes.

Step 3: Adjust the temperature and add flavors and colors.

Once the mixture is homogeneous, add some flavor and coloring to the mixture. These flavors and colors can be freely selected according to personal preference. Once added, the temperature of the mixture needs to be adjusted.

Heat the mixture to about 100 degrees and then cool down to about 40 degrees. This process requires mastery of time and temperature to ensure the quality of the soap mixture.

Step 4: Pour into the mold and cool.

Once the mixture has reached the proper temperature, pour it into the molds that have been prepared. Care needs to be taken in this process so that the mixture does not spill or spill out. Then, allow the mixture to cool naturally. It usually takes 12 to 24 hours to cool and solidify completely.

Step 5: Demoulding and cutting.

Once the soap has cooled completely and solidified, it can be removed from the mold. Then, cut the soap into the desired size and shape. This process requires the use of a knife or cutting machine, and ensures that each cut is straight and neat.

Summary. Making homemade soap is a fun and rewarding way to make a living Natsa that can contribute to your health and the environment. If you master the skills and steps of soap making, you will be able to make high-quality soap and enjoy the wonderful effects of homemade soap.